3DM 2 Online Help

Table of Contents Previous Next Index


Configuring Your Controller > Using Auto-Carving for Multi LUN Support

Using Auto-Carving for Multi LUN Support
Auto-carving is useful for creating multiple volumes out of large arrays at the hardware level. Then, when you boot to the operating system, each volume appears as a different disk drive, simplifying the partitioning required at the operating system level.
A second use of auto-carving is to gain use of the full capacity of units greater than 2 TB in older operating systems. This is because Windows 2003 (32-bit and 64-bit without SP1), Windows XP (32-bit), and FreeBSD 4.x, do not currently recognize unit capacity in excess of 2 TB. For more information see, http://www.3ware.com/kb/article.aspx?id=13431.
When the Auto-Carving policy is on, any new unit larger than a specified size (known as the carve size) will be created as multiple volumes that can be addressed by the operating system as separate volumes. These chunks are sometimes known as multiple LUNs (logical units). However, throughout the 3ware documentation, they are referred to as volumes.
For example, using the default carve size of 2 TB, if the unit is 2.5 TB then it will contain two volumes, with the first volume containing 2TB and the second volume containing 0.5 TB. If the unit is 5.0 TB then it will contain 3 volumes, with the first two volumes containing 2 TB each and the last volume containing 1 TB. (Note: If a specific Boot Volume was also specified in 3BM or CLI, the first volume will be the size specified for the Boot Volume, and then the carve size will be applied to the remainder of the unit. For more information, see Boot volume size.)
Each volume can be treated as an individual disk with its own file system. The default carve size is 2 TB; you can change this to a setting in the range of 1 TB to 32 TB (1024 GB to 32768 GB). 3ware firmware supports a maximum of 32 volumes per controller, up to a total of 32TB.
 
Note: CLI now provides the ability to specify variable sizes for the first 4 volumes of a unit when autocarving. This is done while creating a unit with the /cx add type command attribute [v0=n|vol=a:b:c:d]. See the 3ware SAS/SATA RAID Controller CLI Guide.
If you are migrating a unit to a size that is larger than the carve size and auto-carving is on, multiple volumes will be created.
 
Note: Carving a unit into multiple volumes can have an impact on performance.
 
Note: Operating systems without the 2TB limitation include Linux 2.6, FreeBSD 5.x or later, Windows XP (64bit), Windows 2003 (32-bit and 64-bit with SP1 or newer), Windows 2008 (32-bit and 64-bit) and Windows Vista.
Even though the Linux 2.6 kernel supports partitions larger than 2 TB, the installers for SuSE and Redhat do not. Turn auto-carving on to prevent the installation from failing.
You must turn on the Auto-Carving policy before creating the unit. Units created with this policy turned off will not be affected by a change to the policy. If the policy is turned off later, units that have been carved into volumes will retain their individual volumes; existing data is not affected.
To use auto-carving
1
In 3DM 2, enable Auto-Carving at the bottom of the Management > Controller Settings page.
2
Show Create a new unit or migrate an existing unit to include the drives you want to use.
If the combined capacity of the drives exceeds the carve size, a number of volumes will be created.
3
In 3DM 2, the number of volumes is shown on the Unit Details page.
4
 
If you are configuring a unit for primary storage and it will be greater than 2 TB, be sure to enable the auto-carve policy before creating the unit.

Related Topics

Table of Contents Previous Next Index
www.3ware.com
1-858-535-6517
1-800-840-6055

Copyright AMCC 2004-2009
To contact Support, log in at https://www.3ware.com