










                         SENDMAILTM

              INSTALLATION AND OPERATION GUIDE

                        Eric Allman
                       Claus Assmann
                    Gregory Neil Shapiro
                       Sendmail, Inc.

                       Version 8.739

                 For Sendmail Version 8.14




     SendmailTM  implements  a  general purpose internetwork
mail routing facility under the  UNIX(R)  operating  system.
It is not tied to any one transport protocol -- its function
may be likened to a crossbar switch, relaying messages  from
one  domain  into another.  In the process, it can do a lim-
ited amount of message header editing  to  put  the  message
into  a format that is appropriate for the receiving domain.
All of this is done under the  control  of  a  configuration
file.

     Due  to  the  requirements of flexibility for sendmail,
the configuration file  can  seem  somewhat  unapproachable.
However,  there are only a few basic configurations for most
sites, for which standard configuration files have been sup-
plied.   Most other configurations can be built by adjusting
an existing configuration file incrementally.

     Sendmail is based on RFC  821  (Simple  Mail  Transport
Protocol),  RFC  822 (Internet Mail Headers Format), RFC 974
(MX routing), RFC 1123  (Internet  Host  Requirements),  RFC
1413 (Identification server), RFC 1652 (SMTP 8BITMIME Exten-
sion), RFC 1869 (SMTP Service Extensions),  RFC  1870  (SMTP
SIZE  Extension),  RFC  1891 (SMTP Delivery Status Notifica-
tions), RFC 1892 (Multipart/Report), RFC 1893 (Enhanced Mail
System  Status  Codes),  RFC 1894 (Delivery Status Notifica-
tions), RFC 1985 (SMTP Service Extension for Remote  Message
Queue Starting), RFC 2033 (Local Message Transmission Proto-
col),  RFC  2034  (SMTP  Service  Extension  for   Returning
____________________
   DISCLAIMER: This documentation is under modification.
   Sendmail is a trademark of Sendmail, Inc.




Sendmail Installation and Operation Guide           SMM:08-1







SMM:08-2           Sendmail Installation and Operation Guide


Enhanced  Error  Codes),  RFC 2045 (MIME), RFC 2476 (Message
Submission), RFC 2487 (SMTP  Service  Extension  for  Secure
SMTP over TLS), RFC 2554 (SMTP Service Extension for Authen-
tication), RFC 2821 (Simple  Mail  Transfer  Protocol),  RFC
2822  (Internet  Message  Format), RFC 2852 (Deliver By SMTP
Service Extension), and RFC 2920 (SMTP Service Extension for
Command Pipelining).  However, since sendmail is designed to
work in a wider world, in many cases it can be configured to
exceed these protocols.  These cases are described herein.

     Although  sendmail  is intended to run without the need
for monitoring, it has a number of features that may be used
to  monitor  or  adjust  the operation under unusual circum-
stances.  These features are described.

     Section one  describes  how  to  do  a  basic  sendmail
installation.   Section two explains the day-to-day informa-
tion you should know to maintain your mail system.   If  you
have  a  relatively  normal  site, these two sections should
contain sufficient information for you to  install  sendmail
and  keep it happy.  Section three has information regarding
the command line arguments.   Section  four  describes  some
parameters  that  may  be safely tweaked.  Section five con-
tains the nitty-gritty information about  the  configuration
file.   This  section  is for masochists and people who must
write their own configuration file.  Section  six  describes
configuration  that  can  be  done  at  compile  time.   The
appendixes give a brief but detailed explanation of a number
of features not described in the rest of the paper.


































Sendmail Installation and Operation Guide           SMM:08-7


1.  BASIC INSTALLATION

        There  are  two  basic steps to installing sendmail.
   First, you have to compile and install  the  binary.   If
   sendmail has already been ported to your operating system
   that should be simple.  Second, you must build a run-time
   configuration  file.   This is a file that sendmail reads
   when it starts up that describes  the  mailers  it  knows
   about, how to parse addresses, how to rewrite the message
   header, and the settings of  various  options.   Although
   the configuration file can be quite complex, a configura-
   tion can usually be built using an M4-based configuration
   language.   Assuming  you have the standard sendmail dis-
   tribution, see cf/README for further information.

        The remainder of  this  section  will  describe  the
   installation  of sendmail assuming you can use one of the
   existing configurations and that the  standard  installa-
   tion  parameters are acceptable.  All pathnames and exam-
   ples are given from the root  of  the  sendmail  subtree,
   normally  /usr/src/usr.sbin/sendmail on 4.4BSD-based sys-
   tems.

        Continue with the next section if you  need/want  to
   compile  sendmail yourself.  If you have a running binary
   already on your system, you should probably skip to  sec-
   tion 1.2.

   1.1.  Compiling Sendmail

           All  sendmail source is in the sendmail subdirec-
      tory.  To compile sendmail,  "cd"  into  the  sendmail
      directory and type

          ./Build

      This  will  leave the binary in an appropriately named
      subdirectory, e.g., obj.BSD-OS.2.1.i386.  It works for
      multiple  object  versions  compiled  out  of the same
      directory.

      1.1.1.  Tweaking the Build Invocation

              You can give parameters on the Build  command.
         In  most  cases  these are only used when the obj.*
         directory  is  first  created.   To  restart   from
         scratch, use -c.  These commands include:

         -L libdirs
              A list of directories to search for libraries.

         -I incdirs
              A list of directories to  search  for  include










SMM:08-8           Sendmail Installation and Operation Guide


              files.

         -E envar=value
              Set  an  environment  variable to an indicated
              value before compiling.

         -c   Create a new obj.*  tree before running.

         -f siteconfig
              Read the indicated  site  configuration  file.
              If  this  parameter  is  not  specified, Build
              includes   all   of    the    files    $BUILD-
              TOOLS/Site/site.$oscf.m4      and      $BUILD-
              TOOLS/Site/site.config.m4,  where  $BUILDTOOLS
              is  normally ../devtools and $oscf is the same
              name as used on  the  obj.*   directory.   See
              below for a description of the site configura-
              tion file.

         -S   Skip  auto-configuration.   Build  will  avoid
              auto-detecting  libraries if this is set.  All
              libraries and map definitions must  be  speci-
              fied in the site configuration file.

         Most  other  parameters are passed to the make pro-
         gram; for details see $BUILDTOOLS/README.

      1.1.2.  Creating a Site Configuration File

              (This section is not yet complete.   For  now,
         see  the  file  devtools/README  for details.)  See
         sendmail/README for various compilation flags  that
         can be set.

      1.1.3.  Tweaking the Makefile

              Sendmail  supports  two  different formats for
         the local (on disk) version of  databases,  notably
         the aliases database.  At least one of these should
         be defined if at all possible.

         NDBM      The  ``new  DBM''  format,  available  on
                   nearly  all  systems  around today.  This
                   was the preferred format prior to 4.4BSD.
                   It allows such complex things as multiple
                   databases and closing  a  currently  open
                   database.

         NEWDB     The  Berkeley  DB  package.   If you have
                   this, use it.  It  allows  long  records,
                   multiple  open  databases, real in-memory
                   caching, and so forth.   You  can  define
                   this in conjunction with NDBM; if you do,










Sendmail Installation and Operation Guide           SMM:08-9


                   old alias databases are read, but when  a
                   new  database  is  created  it will be in
                   NEWDB format.  As a nasty  hack,  if  you
                   have NEWDB, NDBM, and NIS defined, and if
                   the alias file  name  includes  the  sub-
                   string  "/yp/", sendmail will create both
                   new and old versions of  the  alias  file
                   during   a  newalias  command.   This  is
                   required because the  Sun  NIS/YP  system
                   reads  the DBM version of the alias file.
                   It's ugly as sin, but it works.

         If neither of these are defined, sendmail reads the
         alias  file  into memory on every invocation.  This
         can be slow and should be avoided.  There are  also
         several methods for remote database access:

         LDAP      Lightweight Directory Access Protocol.

         NIS       Sun's  Network Information Services (for-
                   merly YP).

         NISPLUS   Sun's NIS+ services.

         NETINFO   NeXT's NetInfo service.

         HESIOD    Hesiod service (from Athena).

         Other compilation  flags  are  set  in  conf.h  and
         should be predefined for you unless you are porting
         to a new environment.  For more options  see  send-
         mail/README.

      1.1.4.  Compilation and installation

              After  making  the  local system configuration
         described above, You should be able to compile  and
         install the system.  The script "Build" is the best
         approach on most systems:

             ./Build

         This will use uname(1) to create a custom  Makefile
         for your environment.

              If  you are installing in the standard places,
         you should be able to install using

             ./Build install

         This should install the  binary  in  /usr/sbin  and
         create    links    from   /usr/bin/newaliases   and
         /usr/bin/mailq  to  /usr/sbin/sendmail.   On   most










SMM:08-10          Sendmail Installation and Operation Guide


         systems  it will also format and install man pages.
         Notice: as of version 8.12 sendmail will no  longer
         be  installed  set-user-ID root by default.  If you
         really want to use the old method, you can  specify
         it as target:

             ./Build install-set-user-id


   1.2.  Configuration Files

           Sendmail  cannot  operate without a configuration
      file.  The configuration  defines  the  mail  delivery
      mechanisms  understood  at  this  site,  how to access
      them, how to forward email to remote mail systems, and
      a  number  of  tuning  parameters.  This configuration
      file is detailed in the later portion  of  this  docu-
      ment.

           The  sendmail  configuration  can  be daunting at
      first.  The world is complex, and the mail  configura-
      tion  reflects  that.   The  distribution  includes an
      m4-based configuration package that hides a lot of the
      complexity.  See cf/README for details.

           Our  configuration  files  are processed by m4 to
      facilitate local customization; the  directory  cf  of
      the   sendmail  distribution  directory  contains  the
      source files.  This directory contains several  subdi-
      rectories:

      cf        Both   site-dependent  and  site-independent
                descriptions of hosts.  These can be literal
                host  names  (e.g.,  "ucbvax.mc")  when  the
                hosts are gateways or more general  descrip-
                tions  (such  as  "generic-solaris2.mc" as a
                general  description  of  an  SMTP-connected
                host  running Solaris 2.x.  Files ending .mc
                (``M4   Configuration'')   are   the   input
                descriptions;  the  output  is in the corre-
                sponding .cf file.  The general structure of
                these files is described below.

      domain    Site-dependent    subdomain    descriptions.
                These are tied to the way your  organization
                wants   to   do  addressing.   For  example,
                domain/CS.Berkeley.EDU.m4 is our description
                for  hosts in the CS.Berkeley.EDU subdomain.
                These are referenced  using  the  DOMAIN  m4
                macro in the .mc file.

      feature   Definitions  of  specific features that some
                particular host in  your  site  might  want.










Sendmail Installation and Operation Guide          SMM:08-11


                These  are  referenced  using the FEATURE m4
                macro.  An example  feature  is  use_cw_file
                (which    tells    sendmail   to   read   an
                /etc/mail/local-host-names file  on  startup
                to find the set of local names).

      hack      Local  hacks,  referenced  using the HACK m4
                macro.  Try to avoid these.   The  point  of
                having  them  here  is to make it clear that
                they smell.

      m4        Site-independent m4(1)  include  files  that
                have information common to all configuration
                files.   This  can  be  thought  of   as   a
                "#include" directory.

      mailer    Definitions of mailers, referenced using the
                MAILER m4 macro.  The mailer types that  are
                known  in  this distribution are fax, local,
                smtp, uucp, and  usenet.   For  example,  to
                include  support for the UUCP-based mailers,
                use "MAILER(uucp)".

      ostype    Definitions  describing  various   operating
                system environments (such as the location of
                support files).  These are referenced  using
                the OSTYPE m4 macro.

      sh        Shell  files  used  by the m4 build process.
                You shouldn't have to mess with these.

      siteconfig
                Local UUCP connectivity  information.   This
                directory  has  been supplanted by the mail-
                ertable  feature;  any  new   configurations
                should  use  that  feature  to  do UUCP (and
                other) routing.  The use of  this  directory
                is deprecated.

           If you are in a new domain (e.g., a company), you
      will probably want to create a cf/domain file for your
      domain.   This consists primarily of relay definitions
      and features you want enabled site-wide: for  example,
      Berkeley's domain definition defines relays for BitNET
      and UUCP.  These are specific to Berkeley, and  should
      be   fully-qualified   internet-style   domain  names.
      Please check to make certain they are  reasonable  for
      your domain.

           Subdomains  at  Berkeley  are also represented in
      the cf/domain  directory.   For  example,  the  domain
      CS.Berkeley.EDU  is  the  Computer  Science subdomain,
      EECS.Berkeley.EDU is the  Electrical  Engineering  and










SMM:08-12          Sendmail Installation and Operation Guide


      Computer  Sciences  subdomain, and S2K.Berkeley.EDU is
      the Sequoia 2000 subdomain.  You will probably have to
      add  an  entry to this directory to be appropriate for
      your domain.

           You will have to use or create .mc files  in  the
      cf/cf  subdirectory  for your hosts.  This is detailed
      in the cf/README file.

   1.3.  Details of Installation Files

           This subsection describes the files that comprise
      the sendmail installation.

      1.3.1.  /usr/sbin/sendmail

              The   binary   for   sendmail  is  located  in
         /usr/sbin[1].  It should be set-group-ID  smmsp  as
         described  in sendmail/SECURITY.  For security rea-
         sons, /, /usr, and /usr/sbin  should  be  owned  by
         root, mode 0755[2].

      1.3.2.  /etc/mail/sendmail.cf

              This  is the main configuration file for send-
         mail[3].  This is one of the two  non-library  file
         names  compiled  into  sendmail[4],  the  other  is
         /etc/mail/submit.cf.

              The configuration  file  is  normally  created
         using  the  distribution files described above.  If
         you   have   a    particularly    unusual    system
____________________
   [1]This is usually /usr/sbin on 4.4BSD and newer systems;
many  systems install it in /usr/lib.  I understand it is in
/usr/ucblib on System V Release 4.
   [2]Some  vendors  ship  them owned by bin; this creates a
security hole that is  not  actually  related  to  sendmail.
Other  important  directories  that  should have restrictive
ownerships  and  permissions  are  /bin,   /usr/bin,   /etc,
/etc/mail, /usr/etc, /lib, and /usr/lib.
   [3]Actually, the pathname varies depending on the operat-
ing system; /etc/mail is the preferred directory.  Some old-
er systems install it in /usr/lib/sendmail.cf, and I've also
seen  it in /usr/ucblib.  If you want to move this file, add
-D_PATH_SENDMAILCF=\"/file/name\" to the flags passed to the
C compiler.  Moving this file is not recommended: other pro-
grams and scripts know of this location.
   [4]The system libraries can  reference  other  files;  in
particular,  system  library subroutines that sendmail calls
probably reference /etc/passwd and /etc/resolv.conf.












Sendmail Installation and Operation Guide          SMM:08-13


         configuration you may need to create a special ver-
         sion.  The format of this file is detailed in later
         sections of this document.

      1.3.3.  /etc/mail/submit.cf

              This  is  the  configuration file for sendmail
         when it is used for  initial  mail  submission,  in
         which case it is also called ``Mail Submission Pro-
         gram'' (MSP) in contrast to ``Mail Transfer Agent''
         (MTA).   Starting  with version 8.12, sendmail uses
         one of two different configuration files  based  on
         its  operation  mode  (or  the new -A option).  For
         initial  mail  submission,  i.e.,  if  one  of  the
         options  -bm  (default),  -bs,  or -t is specified,
         submit.cf is used (if available), for other  opera-
         tions sendmail.cf is used.  Details can be found in
         sendmail/SECURITY.  submit.cf is shipped with send-
         mail  (in  cf/cf/) and is installed by default.  If
         changes to the configuration need to be made, start
         with  cf/cf/submit.mc and follow the instruction in
         cf/README.

      1.3.4.  /usr/bin/newaliases

              The newaliases command should just be  a  link
         to sendmail:

             rm -f /usr/bin/newaliases
             ln -s /usr/sbin/sendmail /usr/bin/newaliases

         This  can  be installed in whatever search path you
         prefer for your system.

      1.3.5.  /usr/bin/hoststat

              The hoststat command should just be a link  to
         sendmail, in a fashion similar to newaliases.  This
         command lists the status of the last mail  transac-
         tion  with all remote hosts.  The -v flag will pre-
         vent the status display from being  truncated.   It
         functions  only when the HostStatusDirectory option
         is set.

      1.3.6.  /usr/bin/purgestat

              This command is also a link to  sendmail.   It
         flushes  expired  (Timeout.hoststatus)  information
         that is stored in the HostStatusDirectory tree.














SMM:08-14          Sendmail Installation and Operation Guide


      1.3.7.  /var/spool/mqueue

              The directory /var/spool/mqueue should be cre-
         ated to hold the mail queue.  This directory should
         be mode 0700 and owned by root.

              The actual path of this directory  is  defined
         by  the  QueueDirectory  option  of the sendmail.cf
         file.  To use multiple queues, supply a value  end-
         ing     with    an    asterisk.     For    example,
         /var/spool/mqueue/qd* will use all of the  directo-
         ries  or  symbolic  links  to directories beginning
         with `qd' in /var/spool/mqueue  as  queue  directo-
         ries.   Do not change the queue directory structure
         while sendmail is running.

              If these directories  have  subdirectories  or
         symbolic links to directories named `qf', `df', and
         `xf', then these will be  used  for  the  different
         queue  file  types.   That  is,  the data files are
         stored in the  `df'  subdirectory,  the  transcript
         files  are stored in the `xf' subdirectory, and all
         others are stored in the `qf' subdirectory.

              If shared memory support is compiled in, send-
         mail  stores  the  available  diskspace in a shared
         memory segment to make the values readily available
         to  all children without incurring system overhead.
         In this case, only the  daemon  updates  the  data;
         i.e., the sendmail daemon creates the shared memory
         segment and deletes it if it is terminated.  To use
         this, sendmail must have been compiled with support
         for shared memory (-DSM_CONF_SHM)  and  the  option
         SharedMemoryKey  must  be  set.  Notice: do not use
         the same key for sendmail invocations with  differ-
         ent queue directories or different queue group dec-
         larations.  Access to shared  memory  is  not  con-
         trolled  by  locks, i.e., there is a race condition
         when data in the shared memory  is  updated.   How-
         ever,  since operation of sendmail does not rely on
         the data in the shared memory, this does not  nega-
         tively influence the behavior.

      1.3.8.  /var/spool/clientmqueue

              The  directory  /var/spool/clientmqueue should
         be created to hold the mail queue.  This  directory
         should  be mode 0770 and owned by user smmsp, group
         smmsp.

              The actual path of this directory  is  defined
         by the QueueDirectory option of the submit.cf file.











Sendmail Installation and Operation Guide          SMM:08-15


      1.3.9.  /var/spool/mqueue/.hoststat

              This is a typical value for the  HostStatusDi-
         rectory  option,  containing one file per host that
         this sendmail has chatted  with  recently.   It  is
         normally a subdirectory of mqueue.

      1.3.10.  /etc/mail/aliases*

              The     system    aliases    are    held    in
         "/etc/mail/aliases".  A sample is given  in  "send-
         mail/aliases"  which  includes  some  aliases which
         must be defined:

             cp sendmail/aliases /etc/mail/aliases
             edit /etc/mail/aliases

         You should extend this file with any  aliases  that
         are apropos to your system.

              Normally  sendmail looks at a database version
         of     the     files,     stored     either      in
         "/etc/mail/aliases.dir" and "/etc/mail/aliases.pag"
         or "/etc/mail/aliases.db" depending on which  data-
         base  package  you  are  using.  The actual path of
         this file is defined in the AliasFile option of the
         sendmail.cf file.

              The  permissions  of  the  alias  file and the
         database versions should be 0640 to  prevent  local
         denial  of  service attacks as explained in the top
         level README in the sendmail distribution.  If  the
         permissions  0640  are  used,  be  sure  that  only
         trusted users belong to the group assigned to those
         files.   Otherwise,  files should not even be group
         readable.

      1.3.11.  /etc/rc or /etc/init.d/sendmail

              It will be necessary to start up the  sendmail
         daemon  when your system reboots.  This daemon per-
         forms two functions: it listens on the SMTP  socket
         for connections (to receive mail from a remote sys-
         tem) and it processes  the  queue  periodically  to
         insure that mail gets delivered when hosts come up.

              If  necessary,  add  the  following  lines  to
         "/etc/rc"  (or  "/etc/rc.local"  as appropriate) in
         the area where it is starting up the daemons  on  a
         BSD-base  system,  or on a System-V-based system in
         one    of    the    startup    files,     typically
         "/etc/init.d/sendmail":











SMM:08-16          Sendmail Installation and Operation Guide


             if [ -f /usr/sbin/sendmail -a -f /etc/mail/sendmail.cf ]; then
                  (cd /var/spool/mqueue; rm -f xf*)
                  /usr/sbin/sendmail -bd -q30m &
                  echo -n ' sendmail' >/dev/console
             fi

         The  "cd"  and  "rm" commands insure that all tran-
         script files have been  removed;  extraneous  tran-
         script  files may be left around if the system goes
         down in the middle of processing  a  message.   The
         line  that actually invokes sendmail has two flags:
         "-bd" causes it to listen on  the  SMTP  port,  and
         "-q30m" causes it to run the queue every half hour.

              Some people use a more complex startup script,
         removing  zero  length  qf/hf/Qf files and df files
         for which there is no qf/hf/Qf file.  Note this  is
         not  advisable.   For  example, see Figure 1 for an
         example of a complex script which does  this  clean
         up.

      1.3.12.  /etc/mail/helpfile

              This  is  the  help file used by the SMTP HELP
         command.  It should be copied from  "sendmail/help-
         file":

             cp sendmail/helpfile /etc/mail/helpfile

         The  actual  path  of  this  file is defined in the
         HelpFile option of the sendmail.cf file.

      1.3.13.  /etc/mail/statistics

              If you wish to collect statistics  about  your
         mail   traffic,   you   should   create   the  file
         "/etc/mail/statistics":

             cp /dev/null /etc/mail/statistics
             chmod 0600 /etc/mail/statistics

         This file does not grow.  It is  printed  with  the
         program  "mailstats/mailstats.c."   The actual path
         of this file is defined in  the  S  option  of  the
         sendmail.cf file.

      1.3.14.  /usr/bin/mailq

              If  sendmail  is  invoked  as "mailq," it will
         simulate the -bp flag (i.e.,  sendmail  will  print
         the  contents  of the mail queue; see below).  This
         should be a link to /usr/sbin/sendmail.











Sendmail Installation and Operation Guide          SMM:08-17



____________________________________________________________

#!/bin/sh
# remove zero length qf/hf/Qf files
for qffile in qf* hf* Qf*
do
     if [ -r $qffile ]
     then
          if [ ! -s $qffile ]
          then
               echo -n " <zero: $qffile>" > /dev/console
               rm -f $qffile
          fi
     fi
done
# rename tf files to be qf if the qf does not exist
for tffile in tf*
do
     qffile=`echo $tffile | sed 's/t/q/'`
     if [ -r $tffile -a ! -f $qffile ]
     then
          echo -n " <recovering: $tffile>" > /dev/console
          mv $tffile $qffile
     else
          if [ -f $tffile ]
          then
               echo -n " <extra: $tffile>" > /dev/console
               rm -f $tffile
          fi
     fi
done
# remove df files with no corresponding qf/hf/Qf files
for dffile in df*
do
     qffile=`echo $dffile | sed 's/d/q/'`
     hffile=`echo $dffile | sed 's/d/h/'`
     Qffile=`echo $dffile | sed 's/d/Q/'`
     if [ -r $dffile -a ! -f $qffile -a ! -f $hffile -a ! -f $Qffile ]
     then
          echo -n " <incomplete: $dffile>" > /dev/console
          mv $dffile `echo $dffile | sed 's/d/D/'`
     fi
done
# announce files that have been saved during disaster recovery
for xffile in [A-Z]f*
do
     if [ -f $xffile ]
     then
          echo -n " <panic: $xffile>" > /dev/console
     fi
done











SMM:08-18          Sendmail Installation and Operation Guide


            Figure 1 -- A complex startup script
____________________________________________________________


      1.3.15.  sendmail.pid

              sendmail stores its current pid  in  the  file
         specified   by   the  PidFile  option  (default  is
         _PATH_SENDMAILPID).   sendmail  uses   TempFileMode
         (which defaults to 0600) as the permissions of that
         file to prevent local denial of service attacks  as
         explained  in  the top level README in the sendmail
         distribution.  If the file already exists, then  it
         might   be  necessary  to  change  the  permissions
         accordingly, e.g.,

             chmod 0600 /var/run/sendmail.pid

         Note that as of version 8.13, this file is unlinked
         when sendmail exits.  As a result of this change, a
         script such as the following, which may have worked
         prior to 8.13, will no longer work:

             # stop & start sendmail
             PIDFILE=/var/run/sendmail.pid
             kill `head -1 $PIDFILE`
             `tail -1 $PIDFILE`

         because  it  assumes  that  the  pidfile will still
         exist even after killing the process  to  which  it
         refers.   Below  is  a  script which will work cor-
         rectly on both newer and older versions:

             # stop & start sendmail
             PIDFILE=/var/run/sendmail.pid
             pid=`head -1 $PIDFILE`
             cmd=`tail -1 $PIDFILE`
             kill $pid
             $cmd

         This is just an example script, it does not perform
         any  error checks, e.g., whether the pidfile exists
         at all.

      1.3.16.  Map Files

              To prevent local denial of service attacks  as
         explained  in  the top level README in the sendmail
         distribution, the permissions of map files  created
         by makemap should be 0640.  The use of 0640 implies
         that  only  trusted  users  belong  to  the   group
         assigned  to  those  files.  If those files already
         exist, then it might be  necessary  to  change  the










Sendmail Installation and Operation Guide          SMM:08-19


         permissions accordingly, e.g.,

             cd /etc/mail
             chmod 0640 *.db *.pag *.dir


2.  NORMAL OPERATIONS

   2.1.  The System Log

           The  system  log  is  supported by the syslogd(8)
      program.  All messages from sendmail are logged  under
      the LOG_MAIL facility[5].

      2.1.1.  Format

              Each line in the  system  log  consists  of  a
         timestamp,  the  name of the machine that generated
         it (for logging  from  several  machines  over  the
         local  area  network),  the word "sendmail:", and a
         message[6].    Most  messages  are  a  sequence  of
         name=value pairs.

              The two most common lines are  logged  when  a
         message  is  processed.  The first logs the receipt
         of a message; there will be exactly  one  of  these
         per message.  Some fields may be omitted if they do
         not contain interesting information.  Fields are:

         from      The envelope sender address.

         size      The size of the message in bytes.

         class     The class (i.e., numeric  precedence)  of
                   the message.

         pri       The  initial  message  priority (used for
                   queue sorting).

         nrcpts    The number  of  envelope  recipients  for
                   this message (after aliasing and forward-
                   ing).

         msgid     The message id of the message  (from  the
                   header).

____________________
   [5]Except on Ultrix, which does not support facilities in
the syslog.
   [6]This format may  vary  slightly  if  your  vendor  has
changed the syntax.












SMM:08-20          Sendmail Installation and Operation Guide


         proto     The protocol used to receive this message
                   (e.g., ESMTP or UUCP)

         daemon    The daemon name  from  the  DaemonPortOp-
                   tions setting.

         relay     The machine from which it was received.

         There  is also one line logged per delivery attempt
         (so there can be several per message if delivery is
         deferred or there are multiple recipients).  Fields
         are:

         to        A comma-separated list of the  recipients
                   to this mailer.

         ctladdr   The  ``controlling  user'',  that is, the
                   name of the user whose credentials we use
                   for delivery.

         delay     The  total  delay  between  the time this
                   message  was  received  and  the  current
                   delivery attempt.

         xdelay    The  amount of time needed in this deliv-
                   ery attempt (normally indicative  of  the
                   speed of the connection).

         mailer    The name of the mailer used to deliver to
                   this recipient.

         relay     The  name  of  the  host  that   actually
                   accepted (or rejected) this recipient.

         dsn       The  enhanced  error  code  (RFC 2034) if
                   available.

         stat      The delivery status.

         Not all fields are present  in  all  messages;  for
         example,  the relay is usually not listed for local
         deliveries.

      2.1.2.  Levels

              If  you  have  syslogd(8)  or  an   equivalent
         installed,  you  will be able to do logging.  There
         is a  large  amount  of  information  that  can  be
         logged.   The  log  is  arranged as a succession of
         levels.  At the lowest level only extremely strange
         situations  are logged.  At the highest level, even
         the  most  mundane  and  uninteresting  events  are
         recorded  for  posterity.   As  a  convention,  log










Sendmail Installation and Operation Guide          SMM:08-21


         levels under ten are considered generally "useful;"
         log levels above 64 are reserved for debugging pur-
         poses.  Levels from 11-64 are reserved for  verbose
         information that some sites might want.

              A  complete  description  of the log levels is
         given in section ``Log Level''.

   2.2.  Dumping State

           You can ask sendmail to log a dump  of  the  open
      files and the connection cache by sending it a SIGUSR1
      signal.  The results are logged at LOG_DEBUG priority.

   2.3.  The Mail Queues

           Mail messages may either be delivered immediately
      or be held for  later  delivery.   Held  messages  are
      placed into a holding directory called a mail queue.

           A mail message may be queued for these reasons:

       + If  a mail message is temporarily undeliverable, it
         is queued and delivery is attempted later.  If  the
         message  is addressed to multiple recipients, it is
         queued only for those recipients to  whom  delivery
         is not immediately possible.
       + If  the  SuperSafe  option is set to true, all mail
         messages are queued while delivery is attempted.
       + If the DeliveryMode option is set to queue-only  or
         defer,  all mail is queued, and no immediate deliv-
         ery is attempted.
       + If the load average becomes higher than  the  value
         of  the  QueueLA  option  and  the  QueueFactor (q)
         option divided by the  difference  in  the  current
         load  average  and  the  QueueLA option plus one is
         less than the priority of the message, messages are
         queued rather than immediately delivered.
       + One  or  more addresses are marked as expensive and
         delivery is postponed until the next queue  run  or
         one  or  more address are marked as held via mailer
         which uses the hold mailer flag.
       + The mail message has been marked as quarantined via
         a mail filter or rulesets.
       +

      2.3.1.  Queue Groups and Queue Directories

              There  are one or more mail queues.  Each mail
         queue belongs to a queue group.  There is always  a
         default  queue  group  that  is  called  ``mqueue''
         (which is where messages go by default unless  oth-
         erwise  specified).   The  directory or directories










SMM:08-22          Sendmail Installation and Operation Guide


         which comprise the default queue group  are  speci-
         fied  by the QueueDirectory option.  There are zero
         or more  additional  named  queue  groups  declared
         using the Q command in the configuration file.

              By  default, a queued message is placed in the
         queue group associated with the first recipient  in
         the  recipient list.  A recipient address is mapped
         to a queue group as follows.  First, if there is  a
         ruleset  called ``queuegroup'', and if this ruleset
         maps the address to a queue group name,  then  that
         queue  group  is chosen.  That is, the argument for
         the ruleset is the recipient address and the result
         should be $# followed by the name of a queue group.
         Otherwise,  if  the  mailer  associated  with   the
         address  specifies  a  queue group, then that queue
         group is  chosen.   Otherwise,  the  default  queue
         group is chosen.

              A  message  with  multiple  recipients will be
         split if different queue groups are chosen  by  the
         mapping of recipients to queue groups.

              When a message is placed in a queue group, and
         the queue group has more than one queue, a queue is
         selected randomly.

              If  a  message  with  multiple  recipients  is
         placed into a queue group with the 'r' option (max-
         imum  number  of  recipients  per message) set to a
         positive value N, and if  there  are  more  than  N
         recipients in the message, then the message will be
         split into multiple messages, each of which have at
         most N recipients.

              Notice:  if multiple queue groups are used, do
         not move queue files around, e.g., into a different
         queue  directory.   This may have weird effects and
         can cause mail not to be  delivered.   Queue  files
         and  directories  should  be  treated as opaque and
         should not be manipulated directly.

      2.3.2.  Queue Runs

              sendmail has two different ways to process the
         queue(s).   The first one is to start queue runners
         after certain intervals (``normal'' queue runners),
         the  second  one  is to keep queue runner processes
         around  (``persistent''  queue  runners).   How  to
         select  either  of  these types is discussed in the
         appendix ``COMMAND LINE FLAGS''.  Persistent  queue
         runners  have  the  advantage that no new processes
         need to be spawned at certain intervals; they  just










Sendmail Installation and Operation Guide          SMM:08-23


         sleep  for  a  specified time after they finished a
         queue run.  Another advantage of  persistent  queue
         runners  is  that  only  one process belonging to a
         workgroup (a workgroup is a set  of  queue  groups)
         collects the data for a queue run and then multiple
         queue runner may go ahead using  that  data.   This
         can  significantly reduce the disk I/O necessary to
         read the queue files compared to starting  multiple
         queue runners directly.  Their disadvantage is that
         a new queue run is only  started  after  all  queue
         runners  belonging to a group finished their tasks.
         In case one of the queue runners tries delivery  to
         a  slow  recipient  site at the end of a queue run,
         the next queue run may  be  substantially  delayed.
         In  general  this should be smoothed out due to the
         distribution of those slow jobs, however, for sites
         with  small  number  of  queue  entries  this might
         introduce noticable delays.  In general, persistent
         queue  runners  are  only useful for sites with big
         queues.

      2.3.3.  Manual Intervention

              Under normal conditions the mail queue will be
         processed  transparently.   However,  you  may find
         that manual intervention  is  sometimes  necessary.
         For  example,  if a major host is down for a period
         of time the queue  may  become  clogged.   Although
         sendmail  ought to recover gracefully when the host
         comes up, you may find performance unacceptably bad
         in  the  meantime.   In that case you want to check
         the content of  the  queue  and  manipulate  it  as
         explained in the next two sections.

      2.3.4.  Printing the queue

              The  contents  of  the queue(s) can be printed
         using the mailq command (or by specifying  the  -bp
         flag to sendmail):

             mailq

         This  will produce a listing of the queue id's, the
         size of the message, the date the  message  entered
         the  queue,  and  the  sender  and  recipients.  If
         shared memory support is compiled in, the flag  -bP
         can  be  used to print the number of entries in the
         queue(s), provided  a  process  updates  the  data.
         However,  as explained earlier, the output might be
         slightly wrong, since access to the  shared  memory
         is  not  locked.   For example, ``unknown number of
         entries'' might be shown.   The  internal  counters
         are  updated  after  each  queue run to the correct










SMM:08-24          Sendmail Installation and Operation Guide


         value again.

      2.3.5.  Forcing the queue

              Sendmail should run the queue automatically at
         intervals.   When using multiple queues, a separate
         process will by default be created to run  each  of
         the  queues  unless the queue run is initiated by a
         user with the verbose flag.  The  algorithm  is  to
         read  and  sort  the  queue, and then to attempt to
         process all jobs in order.  When it attempts to run
         the job, sendmail first checks to see if the job is
         locked.  If so, it ignores the job.

              There is no attempt to insure  that  only  one
         queue  processor exists at any time, since there is
         no guarantee that a  job  cannot  take  forever  to
         process  (however, sendmail does include heuristics
         to try to abort jobs that are taking absurd amounts
         of time; technically, this violates RFC 821, but is
         blessed by RFC 1123).  Due  to  the  locking  algo-
         rithm,  it  is impossible for one job to freeze the
         entire queue.  However, an uncooperative  recipient
         host  or a program recipient that never returns can
         accumulate many processes in your system.  Unfortu-
         nately, there is no completely general way to solve
         this.

              In some cases, you may find that a major  host
         going  down  for a couple of days may create a pro-
         hibitively large queue.  This will result in  send-
         mail  spending an inordinate amount of time sorting
         the queue.  This situation can be fixed  by  moving
         the  queue  to a temporary place and creating a new
         queue.  The old queue can be  run  later  when  the
         offending host returns to service.

              To  do  this,  it  is  acceptable  to move the
         entire queue directory:

             cd /var/spool
             mv mqueue omqueue; mkdir mqueue; chmod 0700 mqueue

         You should then kill the existing daemon (since  it
         will  still  be  processing in the old queue direc-
         tory) and create a new daemon.

              To run the old mail queue, issue the following
         command:

             /usr/sbin/sendmail -C /etc/mail/queue.cf -q

         The  -C  flag  specifies an alternate configuration










Sendmail Installation and Operation Guide          SMM:08-25


         file queue.cf which should refer to the moved queue
         directory

             O QueueDirectory=/var/spool/omqueue

         and  the  -q flag says to just run every job in the
         queue.  You can also specify the moved queue direc-
         tory on the command line

             /usr/sbin/sendmail -oQ/var/spool/omqueue -q

         but this requires that you do not have queue groups
         in the configuration file, because  those  are  not
         subdirectories  of  the  moved  directory.  See the
         section  about  ``Queue  Group  Declaration''   for
         details;  you most likely need a different configu-
         ration file to correctly deal  with  this  problem.
         However,  a  proper  configuration  of queue groups
         should avoid filling up queue directories,  so  you
         shouldn't  run  into  this  problem.  If you have a
         tendency toward voyeurism, you can use the -v  flag
         to watch what is going on.

              When  the  queue  is  finally emptied, you can
         remove the directory:

             rmdir /var/spool/omqueue


      2.3.6.  Quarantined Queue Items

              It is possible to "quarantine" mail  messages,
         otherwise  known  as  envelopes.   Envelopes (queue
         files) are stored but not considered  for  delivery
         or  display  unless  the  "quarantine" state of the
         envelope is undone or delivery or display of  quar-
         antined  items  is requested.  Quarantined messages
         are tagged by using a different name for the  queue
         file, 'hf' instead of 'qf', and by adding the quar-
         antine reason to the queue file.

              Delivery or display of quarantined  items  can
         be  requested  using  the  -qQ  flag to sendmail or
         mailq.  Additionally, messages already in the queue
         can  be  quarantined or unquarantined using the new
         -Q flag to sendmail.  For example,

             sendmail -Qreason -q[!][I|R|S][matchstring]

         Quarantines the normal  queue  items  matching  the
         criteria specified by the -q[!][I|R|S][matchstring]
         using the reason given on the -Q flag.  Likewise,











SMM:08-26          Sendmail Installation and Operation Guide


             sendmail -qQ -Q[reason] -q[!][I|R|S|Q][matchstring]

         Change the quarantine reason  for  the  quarantined
         items   matching  the  criteria  specified  by  the
         -q[!][I|R|S|Q][matchstring] using the reason  given
         on the -Q flag.  If there is no reason,
          unquarantine the matching items and make them nor-
         mal queue items.  Note  that  the  -qQ  flag  tells
         sendmail to operate on quarantined items instead of
         normal items.

   2.4.  Disk Based Connection Information

           Sendmail stores a  large  amount  of  information
      about  each  remote system it has connected to in mem-
      ory. It is possible to preserve some of this  informa-
      tion on disk as well, by using the HostStatusDirectory
      option, so that it may be shared between several invo-
      cations  of  sendmail.   This allows mail to be queued
      immediately or skipped during a queue run if there has
      been  a  recent  failure  in  connecting  to  a remote
      machine.  Note: information about a remote  system  is
      stored in a file whose pathname consists of the compo-
      nents of the hostname in reverse order.  For  example,
      the  information  for  host.example.com  is  stored in
      com./example./host.  For top-level  domains  like  com
      this can create a large number of subdirectories which
      on some filesystems can exhaust  some  limits.   More-
      over,  the  performance  of  lookups in directory with
      thousands of entries can be fairly slow  depending  on
      the filesystem implementation.

           Additionally  enabling  SingleThreadDelivery  has
      the added effect of single-threading mail delivery  to
      a  destination.   This  can  be  quite  helpful if the
      remote machine is running an SMTP server that is  eas-
      ily  overloaded  or  cannot  accept more than a single
      connection at a time, but can cause some  messages  to
      be  punted  to a future queue run.  It also applies to
      all hosts,  so  setting  this  because  you  have  one
      machine on site that runs some software that is easily
      overrun can cause mail to other  hosts  to  be  slowed
      down.  If this option is set, you probably want to set
      the MinQueueAge option  as  well  and  run  the  queue
      fairly  frequently;  this  way  jobs  that are skipped
      because another sendmail is talking to the  same  host
      will  be tried again quickly rather than being delayed
      for a long time.

           The disk based host information is  stored  in  a
      subdirectory  of  the  mqueue  directory called .host-












Sendmail Installation and Operation Guide          SMM:08-27


      stat[7].  Removing this directory and its  subdirecto-
      ries  has  an  effect similar to the purgestat command
      and  is  completely  safe.   However,  purgestat  only
      removes expired (Timeout.hoststatus) data.  The infor-
      mation in these directories can be  perused  with  the
      hoststat  command,  which will indicate the host name,
      the last access, and the status of  that  access.   An
      asterisk  in  the  left  most  column indicates that a
      sendmail process currently has  the  host  locked  for
      mail delivery.

           The  disk based connection information is treated
      the same way as memory  based  connection  information
      for  the purpose of timeouts.  By default, information
      about host failures is valid for 30 minutes.  This can
      be adjusted with the Timeout.hoststatus option.

           The  connection information stored on disk may be
      expired at any time with the purgestat command  or  by
      invoking sendmail with the -bH switch.  The connection
      information may be viewed with the hoststat command or
      by invoking sendmail with the -bh switch.

   2.5.  The Service Switch

           The  implementation  of  certain  system services
      such as host and user name lookup is controlled by the
      service switch.  If the host operating system supports
      such a switch, and sendmail knows about  it,  sendmail
      will use the native version.  Ultrix, Solaris, and DEC
      OSF/1 are examples of such systems[8].

           If the underlying operating system does not  sup-
      port  a  service  switch (e.g., SunOS 4.X, HP-UX, BSD)
      then sendmail will provide a stub implementation.  The
      ServiceSwitchFile  option points to the name of a file
      that has the service definitions.  Each line  has  the
      name  of a service and the possible implementations of
      that service.  For example, the file:

          hosts     dns files nis
          aliases   files nis

      will ask sendmail to look for hosts in the Domain Name
      System  first.   If  the  requested  host  name is not
____________________
   [7]This is the usual value of the HostStatusDirectory op-
tion;  it  can,  of  course,  go  anywhere  you like in your
filesystem.
   [8]HP-UX 10 has service switch  support,  but  since  the
APIs  are apparently not available in the libraries sendmail
does not use the native service switch in this release.











SMM:08-28          Sendmail Installation and Operation Guide


      found, it tries local files,  and  if  that  fails  it
      tries  NIS.   Similarly,  when  looking for aliases it
      will try the local files first followed by NIS.

           Notice: since sendmail must access MX records for
      correct operation, it will use DNS if it is configured
      in the ServiceSwitchFile file.  Hence an entry like

          hosts     files dns

      will not avoid DNS lookups even if a host can be found
      in /etc/hosts.

           Service  switches  are not completely integrated.
      For example, despite the  fact  that  the  host  entry
      listed  in the above example specifies to look in NIS,
      on SunOS this won't happen because the  system  imple-
      mentation of gethostbyname(3) doesn't understand this.

   2.6.  The Alias Database

           After recipient addresses are read from the  SMTP
      connection  or command line they are parsed by ruleset
      0, which must resolve to  a  {mailer,  host,  address}
      triple.   If  the flags selected by the mailer include
      the A (aliasable) flag, the address part of the triple
      is  looked up as the key (i.e., the left hand side) in
      the alias database.  If there is a match, the  address
      is  deleted  from  the send queue and all addresses on
      the right hand side of the alias are added in place of
      the  alias that was found.  This is a recursive opera-
      tion, so aliases found in the right hand side  of  the
      alias are similarly expanded.

           The alias database exists in two forms.  One is a
      text form, maintained in the  file  /etc/mail/aliases.
      The aliases are of the form

          name: name1, name2, ...

      Only local names may be aliased; e.g.,

          eric@prep.ai.MIT.EDU: eric@CS.Berkeley.EDU

      will   not   have   the   desired  effect  (except  on
      prep.ai.MIT.EDU, and they probably don't want  me)[9].
      Aliases  may be continued by starting any continuation
____________________
   [9]Actually, any mailer that has the `A' mailer flag  set
will  permit aliasing; this is normally limited to the local
mailer.












Sendmail Installation and Operation Guide          SMM:08-29


      lines with a space or a tab or by putting a  backslash
      directly  before  the  newline.  Blank lines and lines
      beginning with a sharp sign ("#") are comments.

           The second form is processed by  the  ndbm(3)[10]
      or  the Berkeley DB library.  This form is in the file
      /etc/mail/aliases.db    (if    using     NEWDB)     or
      /etc/mail/aliases.dir  and  /etc/mail/aliases.pag  (if
      using NDBM).  This is the form that sendmail  actually
      uses  to  resolve  aliases.  This technique is used to
      improve performance.

           The control of search order is  actually  set  by
      the service switch.  Essentially, the entry

          O AliasFile=switch:aliases

      is  always  added  as the first alias entry; also, the
      first alias file name without a class  (e.g.,  without
      "nis:"  on  the front) will be used as the name of the
      file for a ``files'' entry in the aliases switch.  For
      example, if the configuration file contains

          O AliasFile=/etc/mail/aliases

      and the service switch contains

          aliases   nis files nisplus

      then  aliases  will first be searched in the NIS data-
      base, then in  /etc/mail/aliases,  then  in  the  NIS+
      database.

           You  can  also  use  NIS-based  alias files.  For
      example, the specification:

          O AliasFile=/etc/mail/aliases
          O AliasFile=nis:mail.aliases@my.nis.domain

      will first search the /etc/mail/aliases file and  then
      the   map  named  "mail.aliases"  in  "my.nis.domain".
      Warning: if you build your own NIS-based alias  files,
      be  sure  to  provide the -l flag to makedbm(8) to map
      upper case letters in the keys to lower  case;  other-
      wise,  aliases  with upper case letters in their names
      won't match incoming addresses.

           Additional flags can be  added  after  the  colon
      exactly like a K line -- for example:
____________________
   [10]The gdbm package does not work.












SMM:08-30          Sendmail Installation and Operation Guide


          O AliasFile=nis:-N mail.aliases@my.nis.domain

      will search the appropriate NIS map and always include
      null bytes in the key.  Also:

          O AliasFile=nis:-f mail.aliases@my.nis.domain

      will prevent sendmail from downcasing the  key  before
      the alias lookup.

      2.6.1.  Rebuilding the alias database

              The hash or dbm version of the database may be
         rebuilt explicitly by executing the command

             newaliases

         This is equivalent to giving sendmail the -bi flag:

             /usr/sbin/sendmail -bi


              If  you have multiple aliases databases speci-
         fied, the -bi flag rebuilds all the database  types
         it  understands  (for  example, it can rebuild NDBM
         databases but not NIS databases).

      2.6.2.  Potential problems

              There are a number of problems that can  occur
         with  the  alias  database.  They all result from a
         sendmail process accessing the DBM version while it
         is only partially built.  This can happen under two
         circumstances: One process  accesses  the  database
         while  another  process  is  rebuilding  it, or the
         process rebuilding the database dies (due to  being
         killed  or  a  system  crash) before completing the
         rebuild.

              Sendmail  has  three  techniques  to  try   to
         relieve  these  problems.  First, it ignores inter-
         rupts while rebuilding the  database;  this  avoids
         the problem of someone aborting the process leaving
         a partially rebuilt database.  Second, it locks the
         database source file during the rebuild -- but that
         may not work over NFS or if the file is unwritable.
         Third,  at  the end of the rebuild it adds an alias
         of the form

             @: @

         (which is not  normally  legal).   Before  sendmail
         will  access the database, it checks to insure that










Sendmail Installation and Operation Guide          SMM:08-31


         this entry exists[11].

      2.6.3.  List owners

              If an error occurs on  sending  to  a  certain
         address,  say  "x", sendmail will look for an alias
         of the form "owner-x" to receive the errors.   This
         is  typically  useful  for a mailing list where the
         submitter of the list has no control over the main-
         tenance  of  the list itself; in this case the list
         maintainer would be the owner  of  the  list.   For
         example:

             unix-wizards: eric@ucbarpa, wnj@monet, nosuchuser,
                  sam@matisse
             owner-unix-wizards: unix-wizards-request
             unix-wizards-request: eric@ucbarpa

         would  cause  "eric@ucbarpa"  to get the error that
         will occur when someone sends to  unix-wizards  due
         to the inclusion of "nosuchuser" on the list.

              List  owners  also  cause  the envelope sender
         address to be modified.  The contents of the  owner
         alias are used if they point to a single user, oth-
         erwise the name of the alias itself is  used.   For
         this  reason, and to obey Internet conventions, the
         "owner-" address normally points at the  "-request"
         address;  this  causes  messages to go out with the
         typical  Internet  convention  of   using   ``list-
         request'' as the return address.

   2.7.  User Information Database

           This  option is deprecated, use virtusertable and
      genericstable instead as explained in  cf/README.   If
      you  have a version of sendmail with the user informa-
      tion database compiled in, and you have specified  one
      or  more  databases  using the U option, the databases
      will be searched for a user:maildrop entry.  If found,
      the mail will be sent to the specified address.

   2.8.  Per-User Forwarding (.forward Files)

           As an alternative to the alias database, any user
      may put a file with the name ".forward" in his or  her
      home   directory.    If  this  file  exists,  sendmail
____________________
   [11]The AliasWait option is required in the configuration
for  this  action  to occur.  This should normally be speci-
fied.












SMM:08-32          Sendmail Installation and Operation Guide


      redirects mail for that user to the list of  addresses
      listed  in  the  .forward file.  Note that aliases are
      fully expanded before forward  files  are  referenced.
      For example, if the home directory for user "mckusick"
      has a .forward file with contents:

          mckusick@ernie
          kirk@calder

      then any mail arriving for "mckusick"  will  be  redi-
      rected to the specified accounts.

           Actually,   the   configuration  file  defines  a
      sequence of filenames to check.  By default,  this  is
      the  user's  .forward  file,  but can be defined to be
      more generally using the ForwardPath option.   If  you
      change this, you will have to inform your user base of
      the change; .forward is pretty well incorporated  into
      the collective subconscious.

   2.9.  Special Header Lines

           Several header lines have special interpretations
      defined by the configuration file.  Others have inter-
      pretations  built into sendmail that cannot be changed
      without  changing  the  code.   These  built-ins   are
      described here.

      2.9.1.  Errors-To:

              If  errors  occur  anywhere during processing,
         this header will cause error messages to go to  the
         listed  addresses.   This  is  intended for mailing
         lists.

              The Errors-To: header was created in  the  bad
         old  days  when UUCP didn't understand the distinc-
         tion between an envelope and a header; this  was  a
         hack  to  provide  what should now be passed as the
         envelope sender address.  It should go away.  It is
         only used if the UseErrorsTo option is set.

              The Errors-To: header is officially deprecated
         and will go away in a future release.

      2.9.2.  Apparently-To:

              RFC 822 requires at least one recipient  field
         (To:,  Cc:,  or  Bcc: line) in every message.  If a
         message comes in with no recipients listed  in  the
         message  then sendmail will adjust the header based
         on the "NoRecipientAction" option.  One of the pos-
         sible  actions is to add an "Apparently-To:" header










Sendmail Installation and Operation Guide          SMM:08-33


         line for any recipients it is aware of.

              The Apparently-To: header is non-standard  and
         is both deprecated and strongly discouraged.

      2.9.3.  Precedence

              The  Precedence: header can be used as a crude
         control of message priority.  It  tweaks  the  sort
         order  in the queue and can be configured to change
         the message timeout values.  The  precedence  of  a
         message also controls how delivery status notifica-
         tions (DSNs) are processed for that message.

   2.10.  IDENT Protocol Support

           Sendmail supports the IDENT protocol  as  defined
      in RFC 1413.  Note that the RFC states a client should
      wait at least 30 seconds for a response.  The  default
      Timeout.ident  is 5 seconds as many sites have adopted
      the practice of dropping IDENT queries.  This has lead
      to  delays  processing  mail.   Although this enhances
      identification of the author of an  email  message  by
      doing  a  ``call  back''  to the originating system to
      include the owner of a particular  TCP  connection  in
      the  audit  trail  it is in no sense perfect; a deter-
      mined forger can easily spoof the IDENT protocol.  The
      following description is excerpted from RFC 1413:

           6.  Security Considerations

           The  information  returned by this protocol is at
           most as trustworthy as the host providing  it  OR
           the  organization  operating the host.  For exam-
           ple, a PC in an open lab has few if any  controls
           on it to prevent a user from having this protocol
           return any identifier the user wants.   Likewise,
           if  the host has been compromised the information
           returned may be completely erroneous and mislead-
           ing.

           The Identification Protocol is not intended as an
           authorization or  access  control  protocol.   At
           best, it provides some additional auditing infor-
           mation  with  respect  to  TCP  connections.   At
           worst,  it  can provide misleading, incorrect, or
           maliciously incorrect information.

           The use of the information returned by this  pro-
           tocol  for  other  than auditing is strongly dis-
           couraged.   Specifically,  using   Identification
           Protocol information to make access control deci-
           sions - either as the primary  method  (i.e.,  no










SMM:08-34          Sendmail Installation and Operation Guide


           other  checks)  or as an adjunct to other methods
           may result in a weakening of  normal  host  secu-
           rity.

           An  Identification  server may reveal information
           about users, entities, objects or processes which
           might normally be considered private.  An Identi-
           fication server provides service which is a rough
           analog  of the CallerID services provided by some
           phone companies and many of the same privacy con-
           siderations  and arguments that apply to the Cal-
           lerID service apply to  Identification.   If  you
           wouldn't  run  a  "finger"  server due to privacy
           considerations you may not want to run this  pro-
           tocol.

      In  some  cases your system may not work properly with
      IDENT support due to a bug in the  TCP/IP  implementa-
      tion.   The  symptoms  will be that for some hosts the
      SMTP connection will be closed almost immediately.  If
      this  is  true or if you do not want to use IDENT, you
      should set the IDENT timeout to zero; this  will  dis-
      able the IDENT protocol.

3.  ARGUMENTS

        The  complete  list  of  arguments  to  sendmail  is
   described in detail in Appendix A.  Some important  argu-
   ments are described here.

   3.1.  Queue Interval

           The  amount  of time between forking a process to
      run through the queue is defined by the -q  flag.   If
      you  run  with delivery mode set to i or b this can be
      relatively large, since it will only be relevant  when
      a  host  that was down comes back up.  If you run in q
      mode it should be relatively short, since  it  defines
      the  maximum  amount of time that a message may sit in
      the queue.  (See also the MinQueueAge option.)

           RFC 1123 section 5.3.1.1  says  that  this  value
      should  be at least 30 minutes (although that probably
      doesn't make sense if you use ``queue-only'' mode).

           Notice: the meaning of the interval time  depends
      on  whether  normal  queue runners or persistent queue
      runners are used.  For the  former,  it  is  the  time
      between  subsequent  starts  of  a queue run.  For the
      latter, it is the time sendmail waits after a  persis-
      tent  queue  runner has finished its work to start the
      next one.  Hence for  persistent  queue  runners  this
      interval  should  be  very low, typically no more than










Sendmail Installation and Operation Guide          SMM:08-35


      two minutes.

   3.2.  Daemon Mode

           If you allow incoming mail over  an  IPC  connec-
      tion,  you  should have a daemon running.  This should
      be set by your /etc/rc file using the -bd  flag.   The
      -bd flag and the -q flag may be combined in one call:

          /usr/sbin/sendmail -bd -q30m


           An  alternative  approach  is  to invoke sendmail
      from inetd(8) (use the -bs -Am flags to  ask  sendmail
      to  speak SMTP on its standard input and output and to
      run as MTA).  This works and allows you to wrap  send-
      mail in a TCP wrapper program, but may be a bit slower
      since the configuration file  has  to  be  re-read  on
      every  message  that  comes  in.   If you do this, you
      still need to have a sendmail  running  to  flush  the
      queue:

          /usr/sbin/sendmail -q30m


   3.3.  Forcing the Queue

           In  some  cases  you  may find that the queue has
      gotten clogged for some reason.  You can force a queue
      run  using  the -q flag (with no value).  It is enter-
      taining to use the -v flag (verbose) when this is done
      to watch what happens:

          /usr/sbin/sendmail -q -v


           You  can also limit the jobs to those with a par-
      ticular queue identifier, recipient,  sender,  quaran-
      tine  reason,  or  queue  group using one of the queue
      modifiers.  For example, "-qRberkeley"  restricts  the
      queue  run  to  jobs  that  have the string "berkeley"
      somewhere in one of the  recipient  addresses.   Simi-
      larly,   "-qSstring"  limits  the  run  to  particular
      senders, "-qIstring" limits  it  to  particular  queue
      identifiers,  and  "-qQstring" limits it to particular
      quarantined reasons and only operated  on  quarantined
      queue items, and "-qGstring" limits it to a particular
      queue group.  The named queue group will be  run  even
      if it is set to have 0 runners.  You may also place an
      !  before the I or R or S or Q to indicate  that  jobs
      are  limited to not including a particular queue iden-
      tifier, recipient or sender.  For example,  "-q!Rseat-
      tle" limits the queue run to jobs that do not have the










SMM:08-36          Sendmail Installation and Operation Guide


      string "seattle" somewhere in  one  of  the  recipient
      addresses.   Should  you  need  to terminate the queue
      jobs currently active then a SIGTERM to the parent  of
      the process (or processes) will cleanly stop the jobs.

   3.4.  Debugging

           There are a fairly large number  of  debug  flags
      built  into  sendmail.  Each debug flag has a category
      and a level.  Higher  levels  increase  the  level  of
      debugging activity; in most cases, this means to print
      out more information.  The convention is  that  levels
      greater  than  nine are "absurd," i.e., they print out
      so much information that you wouldn't normally want to
      see them except for debugging that particular piece of
      code.

           You should never run a production sendmail server
      in debug mode.  Many of the debug flags will result in
      debug output being sent over the SMTP  channel  unless
      the  option  -D  is used.  This will confuse many mail
      programs.  However, for testing purposes,  it  can  be
      useful  when  sending  mail manually via telnet to the
      port you are using while debugging.

           A debug category is either an integer,  like  42,
      or  a  name,  like  ANSI.   You can specify a range of
      numeric debug categories using the syntax 17-42.   You
      can  specify  a  set of named debug categories using a
      glob pattern like "sm_trace_*".  At present, only  "*"
      and "?"  are supported in these glob patterns.

           Debug flags are set using the -d option; the syn-
      tax is:

          debug-flag:        -d debug-list
          debug-list:        debug-option [ , debug-option ]*
          debug-option:      debug-categories [ . debug-level ]
          debug-categories:  integer | integer - integer | category-pattern
          category-pattern:  [a-zA-Z_*?][a-zA-Z0-9_*?]*
          debug-level:       integer

      where spaces are for reading ease only.  For example,

          -d12               Set category 12 to level 1
          -d12.3             Set category 12 to level 3
          -d3-17             Set categories 3 through 17 to level 1
          -d3-17.4           Set categories 3 through 17 to level 4
          -dANSI             Set category ANSI to level 1
          -dsm_trace_*.3     Set all named categories matching sm_trace_* to level 3

      For a complete list of the available debug  flags  you
      will  have to look at the code and the TRACEFLAGS file










Sendmail Installation and Operation Guide          SMM:08-37


      in the sendmail distribution (they are too dynamic  to
      keep  this  document up to date).  For a list of named
      debug categories in the sendmail binary, use

          ident /usr/sbin/sendmail | grep Debug


   3.5.  Changing the Values of Options

           Options can be overridden using the -o or -O com-
      mand line flags.  For example,

          /usr/sbin/sendmail -oT2m

      sets  the  T  (timeout) option to two minutes for this
      run only; the equivalent line using  the  long  option
      name is

          /usr/sbin/sendmail -OTimeout.queuereturn=2m


           Some  options  have security implications.  Send-
      mail allows you to set  these,  but  relinquishes  its
      set-user-ID   or   set-group-ID   permissions   there-
      after[12].

   3.6.  Trying a Different Configuration File

           An  alternative  configuration file can be speci-
      fied using the -C flag; for example,

          /usr/sbin/sendmail -Ctest.cf -oQ/tmp/mqueue

      uses the configuration file  test.cf  instead  of  the
      default  /etc/mail/sendmail.cf.  If the -C flag has no
      value it defaults to sendmail.cf in the current direc-
      tory.

           Sendmail  gives  up  set-user-ID root permissions
      (if it has been installed set-user-ID root)  when  you
      use  this  flag,  so  it  is  common to use a publicly
      writable directory (such as /tmp) as the queue  direc-
      tory (QueueDirectory or Q option) while testing.



____________________
   [12]That is, it sets its effective uid to the  real  uid;
thus,  if  you are executing as root, as from root's crontab
file or during system  startup  the  root  permissions  will
still be honored.












SMM:08-38          Sendmail Installation and Operation Guide


   3.7.  Logging Traffic

           Many  SMTP implementations do not fully implement
      the protocol.  For  example,  some  personal  computer
      based  SMTPs  do  not understand continuation lines in
      reply codes.  These can be very hard to trace.  If you
      suspect  such  a  problem, you can set traffic logging
      using the -X flag.  For example,

          /usr/sbin/sendmail -X /tmp/traffic -bd

      will log all traffic in the file /tmp/traffic.

           This logs a lot of data very quickly  and  should
      NEVER  be used during normal operations.  After start-
      ing up such a daemon, force the errant  implementation
      to  send  a message to your host.  All message traffic
      in and out of sendmail, including  the  incoming  SMTP
      traffic, will be logged in this file.

   3.8.  Testing Configuration Files

           When  you build a configuration table, you can do
      a certain amount of testing using the "test  mode"  of
      sendmail.  For example, you could invoke sendmail as:

          sendmail -bt -Ctest.cf

      which  would read the configuration file "test.cf" and
      enter test mode.  In this mode, you enter lines of the
      form:

          rwset address

      where  rwset  is the rewriting set you want to use and
      address is an address to apply the set to.  Test  mode
      shows  you  the steps it takes as it proceeds, finally
      showing you the address it ends up with.  You may  use
      a comma separated list of rwsets for sequential appli-
      cation of rules to an input.  For example:

          3,1,21,4 monet:bollard

      first applies ruleset three to the  input  "monet:bol-
      lard."   Ruleset  one is then applied to the output of
      ruleset three, followed similarly by rulesets  twenty-
      one and four.

           If  you  need  more  detail, you can also use the
      "-d21" flag to turn on more debugging.  For example,

          sendmail -bt -d21.99











Sendmail Installation and Operation Guide          SMM:08-39


      turns on an incredible amount of information; a single
      word  address  is  probably going to print out several
      pages worth of information.

           You should be warned  that  internally,  sendmail
      applies  ruleset 3 to all addresses.  In test mode you
      will have to do that  manually.   For  example,  older
      versions allowed you to use

          0 bruce@broadcast.sony.com

      This version requires that you use:

          3,0 bruce@broadcast.sony.com


           As of version 8.7, some other syntaxes are avail-
      able in test mode:

      .Dxvalue  defines macro x to have the indicated value.
                This is useful when debugging rules that use
                the $&x syntax.

      .Ccvalue  adds the indicated value to class c.

      =Sruleset dumps the contents of the indicated ruleset.

      -ddebug-spec
                is equivalent to the command-line flag.

      Version 8.9 introduced more features:

      ?         shows a help message.

      =M        display the known mailers.

      $m        print the value of macro m.

      $=c       print the contents of class c.

      /mx host  returns the MX records for `host'.

      /parse address
                parse address, returning the value of crack-
                addr, and the parsed address.

      /try mailer addr
                rewrite address into the form it  will  have
                when presented to the indicated mailer.

      /tryflags flags
                set flags used by parsing.  The flags can be
                `H' for Header or `E' for Envelope, and  `S'










SMM:08-40          Sendmail Installation and Operation Guide


                for  Sender or `R' for Recipient.  These can
                be combined,  `HR'  sets  flags  for  header
                recipients.

      /canon hostname
                try to canonify hostname.

      /map mapname key
                look up `key' in the indicated `mapname'.

      /quit     quit address test mode.

   3.9.  Persistent Host Status Information

           When  HostStatusDirectory is enabled, information
      about the status of hosts is maintained  on  disk  and
      can thus be shared between different instantiations of
      sendmail.  The status of the last connection with each
      remote host may be viewed with the command:

          sendmail -bh

      This information may be flushed with the command:

          sendmail -bH

      Flushing  the  information  prevents new sendmail pro-
      cesses from loading it, but does not prevent  existing
      processes  from using the status information that they
      already have.

4.  TUNING

        There are a number of configuration  parameters  you
   may want to change, depending on the requirements of your
   site.  Most of these are set using an option in the  con-
   figuration   file.    For  example,  the  line  "O  Time-
   out.queuereturn=5d" sets option "Timeout.queuereturn"  to
   the value "5d" (five days).

        Most  of these options have appropriate defaults for
   most sites.  However, sites having very high  mail  loads
   may  find they need to tune them as appropriate for their
   mail load.  In particular,  sites  experiencing  a  large
   number  of small messages, many of which are delivered to
   many recipients, may find that they need  to  adjust  the
   parameters dealing with queue priorities.

        All  versions  of  sendmail  prior to 8.7 had single
   character option names.  As of  8.7,  options  have  long
   (multi-character  names).   Although  old short names are
   still accepted, most new options do not have short equiv-
   alents.










Sendmail Installation and Operation Guide          SMM:08-41


        This section only describes the options you are most
   likely to want to tweak; read section 5 for more details.

   4.1.  Timeouts

           All time intervals are set using a scaled syntax.
      For example, "10m"  represents  ten  minutes,  whereas
      "2h30m" represents two and a half hours.  The full set
      of scales is:

          s   seconds
          m   minutes
          h   hours
          d   days
          w   weeks


      4.1.1.  Queue interval

              The argument to  the  -q  flag  specifies  how
         often  a  sub-daemon  will  run the queue.  This is
         typically set to between fifteen  minutes  and  one
         hour.   If  not set, or set to zero, the queue will
         not be run automatically.  RFC 1123 section 5.3.1.1
         recommends  that  this  be  at  least  30  minutes.
         Should you need to terminate the  queue  jobs  cur-
         rently  active  then a SIGTERM to the parent of the
         process (or processes) will cleanly stop the  jobs.

      4.1.2.  Read timeouts

              Timeouts all have option names "Timeout.subop-
         tion".  Most of these control SMTP operations.  The
         recognized  suboptions,  their  default values, and
         the minimum values  allowed  by  RFC  2821  section
         4.5.3.2 (or RFC 1123 section 5.3.2) are:

         connect   The  time  to wait for an SMTP connection
                   to open (the connect(2) system call)  [0,
                   unspecified].   If  zero, uses the kernel
                   default.  In  no  case  can  this  option
                   extend the timeout longer than the kernel
                   provides, but it can shorten it.  This is
                   to  get  around  kernels  that provide an
                   absurdly long connection timeout (90 min-
                   utes in one case).

         iconnect  The  same  as  connect, except it applies
                   only to the initial attempt to connect to
                   a  host  for a given message [0, unspeci-
                   fied].  The concept is that  this  should
                   be very short (a few seconds); hosts that
                   are well connected  and  responsive  will










SMM:08-42          Sendmail Installation and Operation Guide


                   thus be serviced immediately.  Hosts that
                   are slow will not hold up other  deliver-
                   ies in the initial delivery attempt.

         aconnect  [0,   unspecified]  The  overall  timeout
                   waiting for all connection for  a  single
                   delivery  attempt  to  succeed.  If 0, no
                   overall limit is applied.   This  can  be
                   used to restrict the total amount of time
                   trying to connect to a long list of  host
                   that  could  accept  an  e-mail  for  the
                   recipient.  This timeout does  not  apply
                   to  FallbackMXhost,  i.e., if the time is
                   exhausted, the  FallbackMXhost  is  tried
                   next.

         initial   The  wait  for  the  initial 220 greeting
                   message [5m, 5m].

         helo      The wait for a reply from a HELO or  EHLO
                   command   [5m,  unspecified].   This  may
                   require a host name lookup, so five  min-
                   utes is probably a reasonable minimum.

         mail*     The  wait for a reply from a MAIL command
                   [10m, 5m].

         rcpt*     The wait for a reply from a RCPT  command
                   [1h, 5m].  This should be long because it
                   could be pointing at a list that takes  a
                   long time to expand (see below).

         datainit* The  wait for a reply from a DATA command
                   [5m, 2m].

         datablock*#
                   The wait for reading a data  block  (that
                   is,  the body of the message).  [1h, 3m].
                   This  should  be  long  because  it  also
                   applies to programs piping input to send-
                   mail which have no guarantee  of  prompt-
                   ness.

         datafinal*
                   The  wait for a reply from the dot termi-
                   nating a message.  [1h, 10m].  If this is
                   shorter than the time actually needed for
                   the  receiver  to  deliver  the  message,
                   duplicates  will  be  generated.  This is
                   discussed in RFC 1047.

         rset      The wait for a reply from a RSET  command
                   [5m, unspecified].










Sendmail Installation and Operation Guide          SMM:08-43


         quit      The  wait for a reply from a QUIT command
                   [2m, unspecified].

         misc      The wait for a reply  from  miscellaneous
                   (but  short)  commands  such as NOOP (no-
                   operation)  and  VERB  (go  into  verbose
                   mode).  [2m, unspecified].

         command*# In  server  SMTP,  the  time  to wait for
                   another command.  [1h, 5m].

         ident#    The timeout waiting for  a  reply  to  an
                   IDENT query [5s[13], unspecified].

         lhlo      The wait for a reply to an LMTP LHLO com-
                   mand [2m, unspecified].

         auth      The  timeout  for a reply in an SMTP AUTH
                   dialogue [10m, unspecified].

         starttls  The timeout for a reply to an SMTP START-
                   TLS  command  and  the TLS handshake [1h,
                   unspecified].

         fileopen# The  timeout  for  opening  .forward  and
                   :include: files [60s, none].

         control#  The timeout for a complete control socket
                   transaction to complete [2m, none].

         hoststatus#
                   How long status information about a  host
                   (e.g.,  host  down) will be cached before
                   it is  considered  stale  [30m,  unspeci-
                   fied].

         resolver.retrans#
                   The resolver's retransmission time inter-
                   val (in  seconds)  [varies].   Sets  both
                   Timeout.resolver.retrans.first  and Time-
                   out.resolver.retrans.normal.

         resolver.retrans.first#
                   The resolver's retransmission time inter-
                   val (in seconds) for the first attempt to
                   deliver a message [varies].


____________________
   [13]On  some systems the default is zero to turn the pro-
tocol off entirely.












SMM:08-44          Sendmail Installation and Operation Guide


         resolver.retrans.normal#
                   The resolver's retransmission time inter-
                   val (in seconds) for all resolver lookups
                   except   the   first   delivery   attempt
                   [varies].

         resolver.retry#
                   The  number  of  times  to  retransmit  a
                   resolver   query.    Sets   both    Time-
                   out.resolver.retry.first     and    Time-
                   out.resolver.retry.normal [varies].

         resolver.retry.first#
                   The  number  of  times  to  retransmit  a
                   resolver  query  for the first attempt to
                   deliver a message [varies].

         resolver.retry.normal#
                   The  number  of  times  to  retransmit  a
                   resolver query for all resolver lookups
                    except   the   first   delivery  attempt
                   [varies].

         For compatibility with old configuration files,  if
         no  suboption is specified, all the timeouts marked
         with an asterick  (*)  are  set  to  the  indicated
         value.   All but those marked with a pound sign (#)
         apply to client SMTP.

              For example, the lines:

             O Timeout.command=25m
             O Timeout.datablock=3h

         sets the server SMTP command timeout to 25  minutes
         and the input data block timeout to three hours.

      4.1.3.  Message timeouts

              After  sitting in the queue for a few days, an
         undeliverable message will time out.   This  is  to
         insure  that  at  least  the sender is aware of the
         inability to send a message.  The timeout is  typi-
         cally set to five days.  It is sometimes considered
         convenient to also send a warning  message  if  the
         message  is  in  the  queue longer than a few hours
         (assuming you normally have good  connectivity;  if
         your  messages  normally took several hours to send
         you wouldn't want to do this because it wouldn't be
         an  unusual  event).   These timeouts are set using
         the   Timeout.queuereturn   and   Timeout.queuewarn
         options  in the configuration file (previously both
         were set using the T option).










Sendmail Installation and Operation Guide          SMM:08-45


              If the message is submitted using  the  NOTIFY
         SMTP  extension, warning messages will only be sent
         if NOTIFY=DELAY is specified.  The queuereturn  and
         queuewarn  timeouts can be further qualified with a
         tag based on the Precedence: field in the  message;
         they must be one of "urgent" (indicating a positive
         non-zero precedence), "normal" (indicating  a  zero
         precedence),  or  "non-urgent" (indicating negative
         precedences).  For example, setting "Timeout.queue-
         warn.urgent=1h" sets the warning timeout for urgent
         messages only to  one  hour.   The  default  if  no
         precedence  is  indicated is to set the timeout for
         all precedences.   If  the  message  has  a  normal
         (default)  precedence  and  it is a delivery status
         notification  (DSN),  Timeout.queuereturn.dsn   and
         Timeout.queuewarn.dsn can be used to give an alter-
         native warn and return time for  DSNs.   The  value
         "now"  can  be  used  for -O Timeout.queuereturn to
         return entries  immediately  during  a  queue  run,
         e.g.,  to bounce messages independent of their time
         in the queue.

              Since these options are global, and since  you
         cannot  know a priori how long another host outside
         your domain will be down, a  five  day  timeout  is
         recommended.   This  allows  a recipient to fix the
         problem even if it occurs at  the  beginning  of  a
         long  weekend.   RFC 1123 section 5.3.1.1 says that
         this parameter should be ``at least 4-5 days''.

              The Timeout.queuewarn value can be piggybacked
         on  the T option by indicating a time after which a
         warning message should be sent;  the  two  timeouts
         are separated by a slash.  For example, the line

             OT5d/4h

         causes email to fail after five days, but a warning
         message will be sent after four hours.  This should
         be  large  enough  that  the message will have been
         tried several times.

   4.2.  Forking During Queue Runs

           By setting the ForkEachJob (Y)  option,  sendmail
      will fork before each individual message while running
      the queue.  This option was used with earlier releases
      to  prevent  sendmail  from consuming large amounts of
      memory.  It should no longer be necessary  with  send-
      mail  8.12.   If  the  ForkEachJob  option is not set,
      sendmail will keep track of hosts that are down during
      a  queue  run,  which can improve performance dramati-
      cally.










SMM:08-46          Sendmail Installation and Operation Guide


           If the ForkEachJob option is set, sendmail cannot
      use connection caching.

   4.3.  Queue Priorities

           Every  message  is assigned a priority when it is
      first instantiated, consisting of the message size (in
      bytes)  offset  by  the message class (which is deter-
      mined from the Precedence:  header)  times  the  "work
      class  factor"  and the number of recipients times the
      "work recipient factor."   The  priority  is  used  to
      order the queue.  Higher numbers for the priority mean
      that the message will be processed later when  running
      the queue.

           The  message  size is included so that large mes-
      sages are penalized relative to small  messages.   The
      message  class  allows  users  to send "high priority"
      messages by including a "Precedence:" field  in  their
      message; the value of this field is looked up in the P
      lines of the configuration file.  Since the number  of
      recipients  affects  the  amount  of  load  a  message
      presents to the system, this is also included into the
      priority.

           The recipient and class factors can be set in the
      configuration file using the RecipientFactor  (y)  and
      ClassFactor (z) options respectively.  They default to
      30000 (for the recipient factor)  and  1800  (for  the
      class factor).  The initial priority is:

     pri=msgsize-(classxClassFactor)+(nrcptxRecipientFactor)

      (Remember,  higher  values for this parameter actually
      mean that the job will be treated  with  lower  prior-
      ity.)

           The  priority  of a job can also be adjusted each
      time it is processed (that is, each time an attempt is
      made  to deliver it) using the "work time factor," set
      by the RetryFactor (Z) option.  This is added  to  the
      priority,  so  it normally decreases the precedence of
      the job, on the grounds that  jobs  that  have  failed
      many times will tend to fail again in the future.  The
      RetryFactor option defaults to 90000.

   4.4.  Load Limiting

           Sendmail can be asked to queue (but not  deliver)
      mail  if  the  system load average gets too high using
      the QueueLA (x) option.  When the load average exceeds
      the  value of the QueueLA option, the delivery mode is
      set to q (queue only) if the  QueueFactor  (q)  option










Sendmail Installation and Operation Guide          SMM:08-47


      divided  by the difference in the current load average
      and the QueueLA option plus one is less than the  pri-
      ority of the message -- that is, the message is queued
      iff:

                        pri>LQueueFactor_

      The QueueFactor option defaults  to  600000,  so  each
      point  of load average is worth 600000 priority points
      (as described above).

           For  drastic  cases,  the  RefuseLA  (X)   option
      defines  a  load average at which sendmail will refuse
      to  accept  network  connections.   Locally  generated
      mail,  i.e.,  mail  which  is  not  submitted via SMTP
      (including incoming UUCP  mail),  is  still  accepted.
      Notice  that the MSP submits mail to the MTA via SMTP,
      and hence mail will be queued in the client  queue  in
      such  a  case.   Therefore  it is necessary to run the
      client mail queue periodically.

   4.5.  Resource Limits

           Sendmail  has  several  parameters   to   control
      resource  usage.  Besides those mentionted in the pre-
      vious section, there are at  least  MaxDaemonChildren,
      ConnectionRateThrottle,  MaxQueueChildren, and MaxRun-
      nersPerQueue.  The latter  two  limit  the  number  of
      sendmail  processes  that operate on the queue.  These
      are discussed in the section  ``Queue  Group  Declara-
      tion''.   The former two can be used to limit the num-
      ber of incoming connections.  Their appropriate values
      depend  on the host operating system and the hardware,
      e.g., amount of memory.  In many situations  it  might
      be  useful  to  set limits to prevent to have too many
      sendmail  processes,  however,  these  limits  can  be
      abused to mount a denial of service attack.  For exam-
      ple, if MaxDaemonChildren=10 then an attacker needs to
      open  only  10 SMTP sessions to the server, leave them
      idle for most of the time,  and  no  more  connections
      will  be  accepted.   If  this  option is set then the
      timeouts used in a SMTP session should be lowered from
      their default values to their minimum values as speci-
      fied in RFC 2821 and listed in section 4.1.2.

   4.6.  Measures against Denial of Service Attacks

           Sendmail has some built-in measures against  sim-
      ple  denial of service (DoS) attacks.  The SMTP server
      by default slows down if too  many  bad  commands  are
      issued  or  if  some  commands  are repeated too often
      within a session.  Details can be found in the  source
      file  sendmail/srvrsmtp.c  by  looking  for  the macro










SMM:08-48          Sendmail Installation and Operation Guide


      definitions of MAXBADCOMMANDS, MAXNOOPCOMMANDS, MAXHE-
      LOCOMMANDS,  MAXVRFYCOMMANDS, and MAXETRNCOMMANDS.  If
      an SMTP command is issued more often than  the  corre-
      sponding  MAXcmdCOMMANDS  value,  then the response is
      delayed exponentially, starting with a sleep  time  of
      one  second,  up  to  a  maximum  of  four minutes (as
      defined by MAXTIMEOUT).  If the option  MaxDaemonChil-
      dren  is  set  to a value greater than zero, then this
      could make a DoS attack even worse since  it  keeps  a
      connection  open  longer  than necessary.  Therefore a
      connection is terminated with a 421 SMTP reply code if
      the  number  of commands exceeds the limit by a factor
      of two and MAXBADCOMMANDS is set to  a  value  greater
      than zero (the default is 25).

   4.7.  Delivery Mode

           There  are  a number of delivery modes that send-
      mail can operate in, set by the DeliveryMode (d)  con-
      figuration  option.   These  modes specify how quickly
      mail will be delivered.  Legal modes are:

          i   deliver interactively (synchronously)
          b   deliver in background (asynchronously)
          q   queue only (don't deliver)
          d   defer delivery attempts (don't deliver)

      There are tradeoffs.  Mode "i" gives  the  sender  the
      quickest  feedback, but may slow down some mailers and
      is hardly ever necessary.  Mode "b" delivers  promptly
      but can cause large numbers of processes if you have a
      mailer that takes a long time to  deliver  a  message.
      Mode "q" minimizes the load on your machine, but means
      that delivery may be  delayed  for  up  to  the  queue
      interval.   Mode  "d"  is identical to mode "q" except
      that it also prevents lookups in maps including the -D
      flag  from  working during the initial queue phase; it
      is intended for ``dial on  demand''  sites  where  DNS
      lookups might cost real money.  Some simple error mes-
      sages (e.g., host unknown during  the  SMTP  protocol)
      will  be  delayed  using  this  mode.  Mode "b" is the
      usual default.

           If you run in mode "q" (queue only), "d" (defer),
      or  "b"  (deliver  in  background)  sendmail  will not
      expand aliases and follow .forward files upon  initial
      receipt  of  the mail.  This speeds up the response to
      RCPT commands.  Mode "i" should not  be  used  by  the
      SMTP server.














Sendmail Installation and Operation Guide          SMM:08-49


   4.8.  Log Level

           The  level  of  logging  can be set for sendmail.
      The default using a standard  configuration  table  is
      level 9.  The levels are as follows:

      0    Minimal logging.

      1    Serious  system  failures  and potential security
           problems.

      2    Lost communications (network problems) and proto-
           col failures.

      3    Other   serious  failures,  malformed  addresses,
           transient  forward/include   errors,   connection
           timeouts.

      4    Minor failures, out of date alias databases, con-
           nection rejections via check_ rulesets.

      5    Message collection statistics.

      6    Creation of error messages, VRFY  and  EXPN  com-
           mands.

      7    Delivery failures (host or user unknown, etc.).

      8    Successful    deliveries   and   alias   database
           rebuilds.

      9    Messages being deferred  (due  to  a  host  being
           down, etc.).

      10   Database  expansion  (alias,  forward, and userdb
           lookups) and authentication information.

      11   NIS errors and end of job processing.

      12   Logs all SMTP connections.

      13   Log bad user shells, files with improper  permis-
           sions, and other questionable situations.

      14   Logs refused connections.

      15   Log all incoming and outgoing SMTP commands.

      20   Logs  attempts  to run locked queue files.  These
           are not errors, but can be useful to note if your
           queue appears to be clogged.












SMM:08-50          Sendmail Installation and Operation Guide


      30   Lost  locks  (only  if  using  lockf  instead  of
           flock).

      Additionally,  values  above  64  are   reserved   for
      extremely  verbose  debugging  output.  No normal site
      would ever set these.

   4.9.  File Modes

           The modes used for files depend on what function-
      ality  you want and the level of security you require.
      In many cases sendmail does careful  checking  of  the
      modes  of  files  and  directories to avoid accidental
      compromise; if you want to make it  possible  to  have
      group-writable  support  files you may need to use the
      DontBlameSendmail option to turn  off  some  of  these
      checks.

      4.9.1.  To suid or not to suid?

              Sendmail is no longer installed set-user-ID to
         root.  sendmail/SECURITY explains how to  configure
         and  install  sendmail  without set-user-ID to root
         but set-group-ID which is the default configuration
         starting with 8.12.

              The  daemon usually runs as root, unless other
         measures are taken.  At the point where sendmail is
         about  to exec(2) a mailer, it checks to see if the
         userid is zero (root); if so, it resets the  userid
         and  groupid  to a default (set by the U= equate in
         the mailer line; if that is not set,  the  Default-
         User  option  is  used).  This can be overridden by
         setting the S flag to the mailer for  mailers  that
         are  trusted  and must be called as root.  However,
         this will cause mail  processing  to  be  accounted
         (using sa(8)) to root rather than to the user send-
         ing the mail.

              A  middle  ground  is  to  set  the  RunAsUser
         option.   This  causes sendmail to become the indi-
         cated user as soon as it has done the startup  that
         requires  root  privileges  (primarily, opening the
         SMTP socket).  If  you  use  RunAsUser,  the  queue
         directory  (normally  /var/spool/mqueue)  should be
         owned by that user, and  all  files  and  databases
         (including   user   .forward  files,  alias  files,
         :include: files, and external  databases)  must  be
         readable  by  that user.  Also, since sendmail will
         not be able to change its uid, delivery to programs
         or files will be marked as unsafe, e.g., undeliver-
         able, in .forward, aliases,  and  :include:  files.
         Administrators  can  override  this  by setting the










Sendmail Installation and Operation Guide          SMM:08-51


         DontBlameSendmail option to  the  setting  NonRoot-
         SafeAddr.   RunAsUser  is  probably best suited for
         firewall configurations  that  don't  have  regular
         user  logins.   If  the  option is used on a system
         which  performs  local  delivery,  then  the  local
         delivery  agent  must  have  the proper permissions
         (i.e., usually set-user-ID root) since it  will  be
         invoked by the RunAsUser, not by root.

      4.9.2.  Turning off security checks

              Sendmail is very particular about the modes of
         files that it reads or  writes.   For  example,  by
         default  it will refuse to read most files that are
         group writable on the grounds that they might  have
         been tampered with by someone other than the owner;
         it will even refuse to read files in group writable
         directories.   Also, sendmail will refuse to create
         a new aliases database in an unsafe directory.  You
         can  get around this by manually creating the data-
         base file as a trusted user ahead of time and  then
         rebuilding the aliases database with newaliases.

              If  you are quite sure that your configuration
         is safe and you want sendmail to avoid these  secu-
         rity  checks, you can turn off certain checks using
         the DontBlameSendmail option.   This  option  takes
         one  or  more  names  that  disable checks.  In the
         descriptions that follow, "unsafe directory"  means
         a  directory  that is writable by anyone other than
         the owner.  The values are:

         Safe No special handling.

         AssumeSafeChown
              Assume  that  the   chown   system   call   is
              restricted  to  root.   Since some versions of
              UNIX permit regular users to give  away  their
              files  to  other  users  on  some filesystems,
              sendmail often cannot assume that a given file
              was created by the owner, particularly when it
              is in a writable directory.  You can set  this
              flag   if  you  know  that  file  giveaway  is
              restricted on your system.

         ClassFileInUnsafeDirPath
              When reading class files (using the F line  in
              the  configuration file), allow files that are
              in unsafe directories.

         DontWarnForwardFileInUnsafeDirPath
              Prevent logging of unsafe directory path warn-
              ings for non-existent forward files.










SMM:08-52          Sendmail Installation and Operation Guide


         ErrorHeaderInUnsafeDirPath
              Allow the file named in the ErrorHeader option
              to be in an unsafe directory.

         FileDeliveryToHardLink
              Allow delivery to files that are hard links.

         FileDeliveryToSymLink
              Allow delivery  to  files  that  are  symbolic
              links.

         ForwardFileInGroupWritableDirPath
              Allow  .forward files in group writable direc-
              tories.

         ForwardFileInUnsafeDirPath
              Allow .forward files in unsafe directories.

         ForwardFileInUnsafeDirPathSafe
              Allow a .forward file that  is  in  an  unsafe
              directory to include references to program and
              files.

         GroupReadableKeyFile
              Accept a group-readable key file for STARTTLS.

         GroupReadableSASLDBFile
              Accept  a  group-readable  Cyrus SASL password
              file.

         GroupWritableAliasFile
              Allow group-writable alias files.

         GroupWritableDirPathSafe
              Change the definition of "unsafe directory" to
              consider   group-writable  directories  to  be
              safe.  World-writable directories  are  always
              unsafe.

         GroupWritableForwardFile
              Allow group writable .forward files.

         GroupWritableForwardFileSafe
              Accept  group-writable  .forward files as safe
              for program and file delivery.

         GroupWritableIncludeFile
              Allow group wriable :include: files.

         GroupWritableIncludeFileSafe
              Accept group-writable :include: files as  safe
              for program and file delivery.











Sendmail Installation and Operation Guide          SMM:08-53


         GroupWritableSASLDBFile
              Accept  a  group-writable  Cyrus SASL password
              file.

         HelpFileInUnsafeDirPath
              Allow the file named in the HelpFile option to
              be in an unsafe directory.

         IncludeFileInGroupWritableDirPath
              Allow :include: files in group writable direc-
              tories.

         IncludeFileInUnsafeDirPath
              Allow :include: files in unsafe directories.

         IncludeFileInUnsafeDirPathSafe
              Allow a :include: file that is  in  an  unsafe
              directory to include references to program and
              files.

         InsufficientEntropy
              Try to use  STARTTLS  even  if  the  PRNG  for
              OpenSSL  is  not  properly  seeded despite the
              security problems.

         LinkedAliasFileInWritableDir
              Allow an alias  file  that  is  a  link  in  a
              writable directory.

         LinkedClassFileInWritableDir
              Allow  class  files that are links in writable
              directories.

         LinkedForwardFileInWritableDir
              Allow  .forward  files  that  are   links   in
              writable directories.

         LinkedIncludeFileInWritableDir
              Allow   :include:  files  that  are  links  in
              writable directories.

         LinkedMapInWritableDir
              Allow map files that  are  links  in  writable
              directories.   This  includes  alias  database
              files.

         LinkedServiceSwitchFileInWritableDir
              Allow the service switch file  to  be  a  link
              even if the directory is writable.

         MapInUnsafeDirPath
              Allow  maps (e.g., hash, btree, and dbm files)
              in unsafe directories.   This  includes  alias










SMM:08-54          Sendmail Installation and Operation Guide


              database files.

         NonRootSafeAddr
              Do  not  mark  file  and program deliveries as
              unsafe if sendmail is not  running  with  root
              privileges.

         RunProgramInUnsafeDirPath
              Run  programs that are in writable directories
              without logging a warning.

         RunWritableProgram
              Run programs that are group- or world-writable
              without logging a warning.

         TrustStickyBit
              Allow  group  or world writable directories if
              the sticky bit is set on  the  directory.   Do
              not set this on systems which do not honor the
              sticky bit on directories.

         WorldWritableAliasFile
              Accept world-writable alias files.

         WorldWritableForwardfile
              Allow world writable .forward files.

         WorldWritableIncludefile
              Allow world wriable :include: files.

         WriteMapToHardLink
              Allow writes to maps that are hard links.

         WriteMapToSymLink
              Allow writes to maps that are symbolic  links.

         WriteStatsToHardLink
              Allow the status file to be a hard link.

         WriteStatsToSymLink
              Allow the status file to be a symbolic link.

   4.10.  Connection Caching

           When  processing  the queue, sendmail will try to
      keep the last  few  open  connections  open  to  avoid
      startup  and shutdown costs.  This only applies to IPC
      and LPC connections.

           When trying to open a  connection  the  cache  is
      first searched.  If an open connection is found, it is
      probed to see if it is still active by sending a  RSET
      command.   It  is not an error if this fails; instead,










Sendmail Installation and Operation Guide          SMM:08-55


      the connection is closed and reopened.

           Two parameters control the connection cache.  The
      ConnectionCacheSize  (k)  option defines the number of
      simultaneous open connections that will be  permitted.
      If  it  is  set to zero, connections will be closed as
      quickly as possible.  The default is one.  This should
      be  set  as  appropriate for your system size; it will
      limit the amount of  system  resources  that  sendmail
      will  use  during  queue  runs.  Never set this higher
      than 4.

           The ConnectionCacheTimeout (K)  option  specifies
      the  maximum  time  that any cached connection will be
      permitted to idle.  When the idle  time  exceeds  this
      value the connection is closed.  This number should be
      small (under ten minutes) to prevent you from grabbing
      too  many  resources from other hosts.  The default is
      five minutes.

   4.11.  Name Server Access

           Control of host address lookups  is  set  by  the
      hosts  service  entry in your service switch file.  If
      you are on a system that has built-in  service  switch
      support  (e.g.,  Ultrix,  Solaris,  or DEC OSF/1) then
      your system is probably configured  properly  already.
      Otherwise,    sendmail    will    consult   the   file
      /etc/mail/service.switch,  which  should  be  created.
      Sendmail  only  uses  two  entries: hosts and aliases,
      although  system  routines  may  use  other   services
      (notably  the  passwd service for user name lookups by
      getpwname).

           However, some systems (such as SunOS 4.X) will do
      DNS  lookups  regardless of the setting of the service
      switch entry.  In particular, the system routine geth-
      ostbyname(3)  is  used to look up host names, and many
      vendor versions try some combination of DNS, NIS,  and
      file lookup in /etc/hosts without consulting a service
      switch.  Sendmail makes no attempt to work around this
      problem,  and  the DNS lookup will be done anyway.  If
      you do not have a nameserver configured at  all,  such
      as  at  a UUCP-only site, sendmail will get a "connec-
      tion refused" message when it tries to connect to  the
      name  server.   If the hosts switch entry has the ser-
      vice "dns" listed somewhere in the list, sendmail will
      interpret  this  to  mean a temporary failure and will
      queue the mail for  later  processing;  otherwise,  it
      ignores the name server data.

           The  same  technique is used to decide whether to
      do MX lookups.  If you want MX support, you must  have










SMM:08-56          Sendmail Installation and Operation Guide


      "dns" listed as a service in the hosts switch entry.

           The  ResolverOptions  (I)  option  allows  you to
      tweak name server options.  The command line  takes  a
      series of flags as documented in resolver(3) (with the
      leading "RES_" deleted).  Each can be preceded  by  an
      optional `+' or `-'.  For example, the line

          O ResolverOptions=+AAONLY -DNSRCH

      turns  on  the  AAONLY  (accept  authoritative answers
      only) and turns off  the  DNSRCH  (search  the  domain
      path)   options.    Most  resolver  libraries  default
      DNSRCH, DEFNAMES, and RECURSE flags on and all  others
      off.   If  NETINET6 is enabled, most libraries default
      to USE_INET6 as well.  You can also include  "HasWild-
      cardMX"  to specify that there is a wildcard MX record
      matching your domain; this turns off MX matching  when
      canonifying  names,  which  can  lead to inappropriate
      canonifications.   Use   "WorkAroundBrokenAAAA"   when
      faced  with  a broken nameserver that returns SERVFAIL
      (a temporary failure) on T_AAAA (IPv6) lookups  during
      hostname  canonification.   Notice: it might be neces-
      sary to apply the same (or similar)  options  to  sub-
      mit.cf too.

           Version  level  1 configurations (see the section
      about ``Configuration Version Level'') turn DNSRCH and
      DEFNAMES  off  when  doing delivery lookups, but leave
      them  on  everywhere  else.   Version  8  of  sendmail
      ignores  them  when doing canonification lookups (that
      is, when using $[ ... $]), and always does the search.
      If  you  don't  want  to  do automatic name extension,
      don't call $[ ... $].

           The search rules for $[ ... $] are somewhat  dif-
      ferent than usual.  If the name being looked up has at
      least one dot, it always  tries  the  unmodified  name
      first.   If  that  fails,  it tries the reduced search
      path, and lastly tries the unmodified name  (but  only
      for  names  without a dot, since names with a dot have
      already  been  tried).   This  allows  names  such  as
      ``utc.CS''  to match the site in Czechoslovakia rather
      than the site in your local Computer  Science  depart-
      ment.   It  also  prefers  A and CNAME records over MX
      records -- that is, if it finds an MX record it  makes
      note  of it, but keeps looking.  This way, if you have
      a wildcard MX record matching your domain, it will not
      assume that all names match.

           To  completely turn off all name server access on
      systems without service switch support (such as  SunOS
      4.X)  you  will  have to recompile with -DNAMED_BIND=0










Sendmail Installation and Operation Guide          SMM:08-57


      and remove -lresolv from the list of libraries  to  be
      searched when linking.

   4.12.  Moving the Per-User Forward Files

           Some  sites mount each user's home directory from
      a local disk  on  their  workstation,  so  that  local
      access  is fast.  However, the result is that .forward
      file lookups from a central mail server are slow.   In
      some  cases,  mail  can  even be delivered on machines
      inappropriately because of a file server  being  down.
      The  performance  can be especially bad if you run the
      automounter.

           The ForwardPath (J) option allows you  to  set  a
      path  of  forward files.  For example, the config file
      line

          O ForwardPath=/var/forward/$u:$z/.forward.$w

      would first look for a file with the same name as  the
      user's login in /var/forward; if that is not found (or
      is inaccessible) the file ``.forward.machinename''  in
      the  user's  home directory is searched.  A truly per-
      verse site could also search by sender  by  using  $r,
      $s, or $f.

           If  you  create a directory such as /var/forward,
      it should be mode 1777 (that is, the sticky bit should
      be  set).   Users  should  create the files mode 0644.
      Note that you must use the  ForwardFileInUnsafeDirPath
      and   ForwardFileInUnsafeDirPathSafe  flags  with  the
      DontBlameSendmail option to allow forward files  in  a
      world  writable directory.  This might also be used as
      a denial of service attack (users could create forward
      files  for other users); a better approach might be to
      create /var/forward mode 0755 and create  empty  files
      for  each user, owned by that user, mode 0644.  If you
      do this, you don't have to set  the  DontBlameSendmail
      options indicated above.

   4.13.  Free Space

           On  systems  that have one of the system calls in
      the statfs(2) family (including  statvfs  and  ustat),
      you can specify a minimum number of free blocks on the
      queue filesystem using the MinFreeBlocks  (b)  option.
      If there are fewer than the indicated number of blocks
      free on the filesystem on which the queue  is  mounted
      the  SMTP  server  will reject mail with the 452 error
      code.  This invites  the  SMTP  client  to  try  again
      later.











SMM:08-58          Sendmail Installation and Operation Guide


           Beware  of  setting  this option too high; it can
      cause rejection of email when that mail would be  pro-
      cessed without difficulty.

   4.14.  Maximum Message Size

           To  avoid  overflowing  your  system with a large
      message, the MaxMessageSize option can be set  to  set
      an  absolute  limit  on  the  size of any one message.
      This will be advertised  in  the  ESMTP  dialogue  and
      checked during message collection.

   4.15.  Privacy Flags

           The  PrivacyOptions  (p) option allows you to set
      certain ``privacy'' flags.   Actually,  many  of  them
      don't  give you any extra privacy, rather just insist-
      ing that client SMTP  servers  use  the  HELO  command
      before  using certain commands or adding extra headers
      to indicate possible spoof attempts.

           The option takes a  series  of  flag  names;  the
      final privacy is the inclusive or of those flags.  For
      example:

          O PrivacyOptions=needmailhelo, noexpn

      insists that the HELO or EHLO command be used before a
      MAIL  command  is  accepted and disables the EXPN com-
      mand.

           The flags are detailed in section 5.6.

   4.16.  Send to Me Too

           Beginning with version 8.10, sendmail includes by
      default  the (envelope) sender in any list expansions.
      For example, if "matt" sends to a list  that  contains
      "matt" as one of the members he will get a copy of the
      message.  If the MeToo option is set to FALSE (in  the
      configuration  file  or  via  the  command line), this
      behavior is changed, i.e., the  (envelope)  sender  is
      excluded in list expansions.

5.  THE WHOLE SCOOP ON THE CONFIGURATION FILE

        This  section  describes  the  configuration file in
   detail.

        There is one point that should be made clear immedi-
   ately:  the  syntax of the configuration file is designed
   to be reasonably easy to parse, since this is done  every
   time  sendmail starts up, rather than easy for a human to










Sendmail Installation and Operation Guide          SMM:08-59


   read or write.  The configuration file should  be  gener-
   ated via the method described in cf/README, it should not
   be edited directly unless someone is  familiar  with  the
   internals of the syntax described here and it is not pos-
   sible to achieve  the  desired  result  via  the  default
   method.

        The  configuration  file is organized as a series of
   lines, each of  which  begins  with  a  single  character
   defining  the  semantics for the rest of the line.  Lines
   beginning with a space or a tab  are  continuation  lines
   (although  the  semantics  are  not  well defined in many
   places).  Blank lines and lines beginning  with  a  sharp
   symbol (`#') are comments.

   5.1.  R and S -- Rewriting Rules

           The  core  of  address  parsing are the rewriting
      rules.  These are an ordered production system.  Send-
      mail  scans through the set of rewriting rules looking
      for a match on the left hand side (LHS) of  the  rule.
      When  a  rule  matches, the address is replaced by the
      right hand side (RHS) of the rule.

           There are several sets of rewriting rules.   Some
      of  the  rewriting  sets  are used internally and must
      have specific semantics.  Other rewriting sets do  not
      have  specifically assigned semantics, and may be ref-
      erenced by the mailer definitions or by other  rewrit-
      ing sets.

           The syntax of these two commands are:

          Sn

      Sets the current ruleset being collected to n.  If you
      begin a ruleset more than once it appends to  the  old
      definition.

          Rlhs rhs comments

      The fields must be separated by at least one tab char-
      acter; there may be embedded  spaces  in  the  fields.
      The lhs is a pattern that is applied to the input.  If
      it matches, the input is rewritten to  the  rhs.   The
      comments are ignored.

           Macro  expansions  of  the  form $x are performed
      when the configuration file is read.  A literal $  can
      be  included using $$.  Expansions of the form $&x are
      performed at run time using a  somewhat  less  general
      algorithm.   This  is  intended  only  for referencing
      internally defined macros such as $h that are  changed










SMM:08-60          Sendmail Installation and Operation Guide


      at runtime.

      5.1.1.  The left hand side

              The left hand side of rewriting rules contains
         a  pattern.   Normal  words  are   simply   matched
         directly.   Metasyntax is introduced using a dollar
         sign.  The metasymbols are:

             $*   Match zero or more tokens
             $+   Match one or more tokens
             $-   Match exactly one token
             $=x  Match any phrase in class x
             $~x  Match any word not in class x

         If any of these match, they  are  assigned  to  the
         symbol  $n  for replacement on the right hand side,
         where n is the index in the LHS.  For  example,  if
         the LHS:

             $-:$+

         is applied to the input:

             UCBARPA:eric

         the  rule  will match, and the values passed to the
         RHS will be:

             $1  UCBARPA
             $2  eric


              Additionally, the LHS can include $@ to  match
         zero tokens.  This is not bound to a $n on the RHS,
         and is normally only used when it stands  alone  in
         order to match the null input.

      5.1.2.  The right hand side

              When  the  left  hand side of a rewriting rule
         matches, the input is deleted and replaced  by  the
         right  hand  side.  Tokens are copied directly from
         the RHS unless  they  begin  with  a  dollar  sign.
         Metasymbols are:


















Sendmail Installation and Operation Guide          SMM:08-61


             $n         Substitute indefinite token n from LHS
             $[name$]   Canonicalize name
             $(map key $@arguments $:default $)
                        Generalized keyed mapping function
             $>n        "Call" ruleset n
             $#mailer   Resolve to mailer
             $@host     Specify host
             $:user     Specify user


              The  $n  syntax  substitutes the corresponding
         value from a $+, $-, $*, $=, or  $~  match  on  the
         LHS.  It may be used anywhere.

              A  host  name  enclosed  between  $[ and $] is
         looked up in the host database(s) and  replaced  by
         the canonical  name[14].   For  example,  "$[ftp$]"
         might      become     "ftp.CS.Berkeley.EDU"     and
         "$[[128.32.130.2]$]"     would     become     "van-
         gogh.CS.Berkeley.EDU."    Sendmail  recognizes  its
         numeric IP address without calling the name  server
         and replaces it with its canonical name.

              The  $(  ...  $) syntax is a more general form
         of lookup; it  uses  a  named  map  instead  of  an
         implicit map.  If no lookup is found, the indicated
         default is inserted; if no default is specified and
         no  lookup  matches,  the  value is left unchanged.
         The arguments are passed to the  map  for  possible
         use.

              The  $>n  syntax  causes  the remainder of the
         line to be substituted as usual and then passed  as
         the  argument  to  ruleset  n.   The final value of
         ruleset n then becomes the  substitution  for  this
         rule.   The  $> syntax expands everything after the
         ruleset name to the end of the  replacement  string
         and  then  passes  that as the initial input to the
         ruleset.  Recursive calls are allowed.   For  exam-
         ple,

             $>0 $>3 $1

         expands  $1,  passes  that  to  ruleset 3, and then
         passes the result of ruleset 3 to ruleset 0.

              The $# syntax should only be used  in  ruleset
         zero,  a  subroutine  of  ruleset zero, or rulesets
____________________
   [14]This  is  actually  completely  equivalent  to $(host
hostname$).  In particular, a $: default can be used.












SMM:08-62          Sendmail Installation and Operation Guide


         that  return  decisions  (e.g.,  check_rcpt).    It
         causes evaluation of the ruleset to terminate imme-
         diately, and signals to sendmail that  the  address
         has  completely  resolved.  The complete syntax for
         ruleset 0 is:

             $#mailer $@host $:user

         This specifies the  {mailer,  host,  user}  3-tuple
         necessary  to  direct  the mailer.  Note: the third
         element ( user ) is often also called address part.
         If  the  mailer is local the host part may be omit-
         ted[15].  The mailer must be a single word, but the
         host and user may be multi-part.  If the mailer  is
         the  built-in  IPC mailer, the host may be a colon-
         separated list of hosts that are searched in  order
         for  the  first  working  address  (exactly like MX
         records).  The  user  is  later  rewritten  by  the
         mailer-specific envelope rewriting set and assigned
         to the $u macro.  As a special case, if the  mailer
         specified  has the F=@ flag specified and the first
         character of the  $:  value  is  "@",  the  "@"  is
         stripped  off,  and  a  flag  is set in the address
         descriptor that causes sendmail to not do ruleset 5
         processing.

              Normally, a rule that matches is retried, that
         is, the rule loops until it fails.  A RHS may  also
         be  preceded  by a $@ or a $: to change this behav-
         ior.  A $@ prefix causes the ruleset to return with
         the remainder of the RHS as the value.  A $: prefix
         causes the rule to terminate immediately,  but  the
         ruleset to continue; this can be used to avoid con-
         tinued  application  of  a  rule.   The  prefix  is
         stripped before continuing.

              The  $@ and $: prefixes may precede a $> spec;
         for example:

             R$+     $: $>7 $1

         matches anything, passes that to ruleset seven, and
         continues; the $: is necessary to avoid an infinite
         loop.


____________________
   [15]You may want to use it for special "per user"  exten-
sions.   For  example, in the address "jgm+foo@CMU.EDU"; the
"+foo" part is not part of the user name, and is  passed  to
the local mailer for local use.












Sendmail Installation and Operation Guide          SMM:08-63


              Substitution occurs in  the  order  described,
         that  is,  parameters from the LHS are substituted,
         hostnames  are  canonicalized,  "subroutines"   are
         called, and finally $#, $@, and $: are processed.

      5.1.3.  Semantics of rewriting rule sets

              There  are  six  rewriting sets that have spe-
         cific semantics.  Five  of  these  are  related  as
         depicted by figure 1.

              Ruleset  three  should  turn  the address into
         "canonical form."  This form should have the  basic
         syntax:

             local-part@host-domain-spec

         Ruleset  three  is applied by sendmail before doing
         anything with any address.

              If no "@" sign is specified,  then  the  host-
         domain-spec  may  be appended (box "D" in Figure 1)
         from the sender address (if the C flag  is  set  in
         the  mailer definition corresponding to the sending
         mailer).

              Ruleset zero is applied after ruleset three to
         addresses that are going to actually specify recip-
         ients.   It  must  resolve  to  a  {mailer,   host,
         address} triple.  The mailer must be defined in the

____________________________________________________________

                    +---+
                 -->| 0 |-->resolved address
                /   +---+
               /            +---+   +---+
              /        ---->| 1 |-->| S |--
       +---+ / +---+  /     +---+   +---+  \    +---+
addr-->| 3 |-->| D |--                      --->| 4 |-->msg
       +---+   +---+  \     +---+   +---+  /    +---+
                        --->| 2 |-->| R |--
                            +---+   +---+

            Figure 1 -- Rewriting set semantics
          D -- sender domain addition
          S -- mailer-specific sender rewriting
          R -- mailer-specific recipient rewriting
____________________________________________________________














SMM:08-64          Sendmail Installation and Operation Guide


         mailer definitions  from  the  configuration  file.
         The  host  is  defined into the $h macro for use in
         the  argv  expansion  of  the   specified   mailer.
         Notice:  since  the envelope sender address will be
         used if a  delivery  status  notification  must  be
         send,  i.e., is may specify a recipient, it is also
         run through ruleset zero.  If ruleset zero  returns
         a  temporary  error  4xy then delivery is deferred.
         This can be used to temporarily  disable  delivery,
         e.g., based on the time of the day or other varying
         parameters.  It should not be used to quarantine e-
         mails.

              Rulesets one and two are applied to all sender
         and recipient  addresses  respectively.   They  are
         applied before any specification in the mailer def-
         inition.  They must never resolve.

              Ruleset four is applied to  all  addresses  in
         the  message.   It  is  typically used to translate
         internal to external form.

              In addition, ruleset 5 is applied to all local
         addresses  (specifically,  those  that resolve to a
         mailer with the `F=5' flag set) that  do  not  have
         aliases.   This allows a last minute hook for local
         names.

      5.1.4.  Ruleset hooks

              A few extra rulesets are  defined  as  "hooks"
         that  can be defined to get special features.  They
         are all named rulesets.  The  "check_*"  forms  all
         give  accept/reject  status; falling off the end or
         returning normally is an accept, and  resolving  to
         $#error is a reject or quarantine.  Quarantining is
         chosen by specifying quarantine in the second  part
         of the mailer triplet:

             $#error $@ quarantine $: Reason for quarantine

         Many  of  these  can  also  resolve  to the special
         mailer name $#discard; this accepts the message  as
         though  it  were  successful  but  then discards it
         without delivery.  Note, this mailer cannot be cho-
         sen  as  a mailer in ruleset 0.  Note also that all
         "check_*" rulesets  have  to  deal  with  temporary
         failures,  especially  for map lookups, themselves,
         i.e., they should return a temporary error code  or
         at  least  they  should  make  a proper decision in
         those cases.












Sendmail Installation and Operation Guide          SMM:08-65


         5.1.4.1.  check_relay

                 The check_relay ruleset is called  after  a
            connection is accepted by the daemon.  It is not
            called when sendmail is started  using  the  -bs
            option.  It is passed

                client.host.name $| client.host.address

            where  $|  is a metacharacter separating the two
            parts.  This ruleset can reject connections from
            various locations.  Note that it only checks the
            connecting SMTP client IP address and  hostname.
            It does not check for third party message relay-
            ing.  The  check_rcpt  ruleset  discussed  below
            usually does third party message relay checking.

         5.1.4.2.  check_mail

                 The check_mail ruleset is passed  the  user
            name parameter of the SMTP MAIL command.  It can
            accept or reject the address.

         5.1.4.3.  check_rcpt

                 The check_rcpt ruleset is passed  the  user
            name parameter of the SMTP RCPT command.  It can
            accept or reject the address.

         5.1.4.4.  check_data

                 The check_data ruleset is called after  the
            SMTP  DATA  command, its parameter is the number
            of recipients.  It can accept or reject the com-
            mand.

         5.1.4.5.  check_compat

                 The check_compat ruleset is passed

                sender-address $| recipient-address

            where  $|  is  a  metacharacter  separating  the
            addresses.  It can accept or reject mail  trans-
            fer  between  these  two addresses much like the
            checkcompat()  function.   Note:   while   other
            check_*  rulesets  are  invoked  during the SMTP
            mail  receiption  stage  (i.e.,  in   the   SMTP
            server), check_compat is invoked during the mail
            delivery stage.













SMM:08-66          Sendmail Installation and Operation Guide


         5.1.4.6.  check_eoh

                 The check_eoh ruleset is passed

                number-of-headers $| size-of-headers

            where $| is a metacharacter separating the  num-
            bers.   These  numbers can be used for size com-
            parisons with the arith  map.   The  ruleset  is
            triggered  after  all  of  the headers have been
            read.  It can be used to  correlate  information
            gathered  from  those  headers  using  the macro
            storage map.  One possible use is to check for a
            missing header.  For example:

                Kstorage macro
                HMessage-Id: $>CheckMessageId

                SCheckMessageId
                # Record the presence of the header
                R$*            $: $(storage {MessageIdCheck} $@ OK $) $1
                R< $+ @ $+ >   $@ OK
                R$*            $#error $: 553 Header Error

                Scheck_eoh
                # Check the macro
                R$*            $: < $&{MessageIdCheck} >
                # Clear the macro for the next message
                R$*            $: $(storage {MessageIdCheck} $) $1
                # Has a Message-Id: header
                R< $+ >        $@ OK
                # Allow missing Message-Id: from local mail
                R$*            $: < $&{client_name} >
                R< >           $@ OK
                R< $=w >       $@ OK
                # Otherwise, reject the mail
                R$*            $#error $: 553 Header Error

            Keep  in  mind  the  Message-Id: header is not a
            required header and is  not  a  guaranteed  spam
            indicator.   This  ruleset  is  an  example  and
            should probably not be used in production.

         5.1.4.7.  check_eom

                 The check_eom ruleset is called  after  the
            end  of  a message, its parameter is the message
            size.  It can accept or reject the message.

         5.1.4.8.  check_etrn

                 The check_etrn ruleset is passed the param-
            eter of the SMTP ETRN command.  It can accept or










Sendmail Installation and Operation Guide          SMM:08-67


            reject the command.

         5.1.4.9.  check_expn

                 The check_expn ruleset is passed  the  user
            name parameter of the SMTP EXPN command.  It can
            accept or reject the address.

         5.1.4.10.  check_vrfy

                 The check_vrfy ruleset is passed  the  user
            name parameter of the SMTP VRFY command.  It can
            accept or reject the command.

         5.1.4.11.  trust_auth

                 The trust_auth ruleset is passed the  AUTH=
            parameter  of the SMTP MAIL command.  It is used
            to  determine  whether  this  value  should   be
            trusted.  In  order  to  make this decision, the
            ruleset may make use of  the  various  ${auth_*}
            macros.   If  the  ruleset  does  resolve to the
            "error"  mailer  the  AUTH=  parameter  is   not
            trusted  and  hence  not  passed  on to the next
            relay.

         5.1.4.12.  tls_client

                 The tls_client ruleset is called when send-
            mail  acts  as  server, after a STARTTLS command
            has  been  issued,  and  from  check_mail.   The
            parameter is the value of ${verify} and STARTTLS
            or MAIL,  respectively.   If  the  ruleset  does
            resolve  to  the "error" mailer, the appropriate
            error code is returned to the client.

         5.1.4.13.  tls_server

                 The tls_server ruleset is called when send-
            mail  acts  as  client  after a STARTTLS command
            (should) have been issued.  The parameter is the
            value of ${verify}.  If the ruleset does resolve
            to the "error" mailer, the connection is aborted
            (treated  as non-deliverable with a permanent or
            temporary error).

         5.1.4.14.  tls_rcpt

                 The tls_rcpt ruleset is  called  each  time
            before a RCPT TO command is sent.  The parameter
            is the current recipient.  If the  ruleset  does
            resolve  to the "error" mailer, the RCPT TO com-
            mand is suppressed (treated  as  non-deliverable










SMM:08-68          Sendmail Installation and Operation Guide


            with  a  permanent  or  temporary  error).  This
            ruleset allows to require encryption or  verifi-
            cation  of  the recipient's MTA even if the mail
            is somehow  redirected  to  another  host.   For
            example,  sending  mail  to luke@endmail.org may
            get redirected to a host  named  death.star  and
            hence  the  tls_server  ruleset won't apply.  By
            introducing  per  recipient  restrictions   such
            attacks  (e.g.,  via  DNS  spoofing) can be made
            impossible.  See cf/README how this ruleset  can
            be used.

         5.1.4.15.  srv_features

                 The srv_features ruleset is called with the
            connecting client's host name when a client con-
            nects  to  sendmail.  This ruleset should return
            $# followed by a list of options (single charac-
            ters  delimited  by white space).  If the return
            value starts with anything else it  is  silently
            ignored.   Generally  upper case characters turn
            off a feature while lower case  characters  turn
            it  on.   Option  `S'  causes  the server not to
            offer STARTTLS, which is useful to interact with
            MTAs/MUAs  that have broken STARTTLS implementa-
            tions by simply not offering it.  `V' turns  off
            the  request for a client certificate during the
            TLS handshake.  Options  `A'  and  `P'  suppress
            SMTP  AUTH and PIPELINING, respectively.  `c' is
            the  equivalent  to  AuthOptions=p,   i.e.,   it
            doesn't  permit mechanisms susceptible to simple
            passive attack (e.g., PLAIN,  LOGIN),  unless  a
            security  layer  is active.  Option `l' requires
            SMTP AUTH for a connection.  Options  'B',  'D',
            'E',  and 'X' suppress SMTP VERB, DSN, ETRN, and
            EXPN, respectively.



























Sendmail Installation and Operation Guide          SMM:08-69


                A        Do not offer AUTH
                a        Offer AUTH (default)
                B        Do not offer VERB
                b        Offer VERB (default)
                C        Do not require security layer for
                         plaintext AUTH (default)
                c        Require security layer for plaintext AUTH
                D        Do not offer DSN
                d        Offer DSN (default)
                E        Do not offer ETRN
                e        Offer ETRN (default)
                L        Do not require AUTH (default)
                l        Require AUTH
                P        Do not offer PIPELINING
                p        Offer PIPELINING (default)
                S        Do not offer STARTTLS
                s        Offer STARTTLS (default)
                V        Do not request a client certificate
                v        Request a client certificate (default)
                X        Do not offer EXPN
                x        Offer EXPN (default)

            Note: the entries marked  as  ``(default)''  may
            require  that  some configuration has been made,
            e.g., SMTP AUTH is only  available  if  properly
            configured.    Moreover,  many  options  can  be
            changed on a global basis via other settings  as
            explained in this document, e.g., via DaemonPor-
            tOptions.

                 The ruleset may return `$#temp' to indicate
            that  there  is  a temporary problem determining
            the correct features, e.g., if a map is unavail-
            able.   In  that  case, the SMTP server issues a
            temporary failure and does not accept email.

         5.1.4.16.  try_tls

                 The try_tls ruleset is called when sendmail
            connects  to  another  MTA.  If the ruleset does
            resolve to the "error" mailer, sendmail does not
            try  STARTTLS  even  if  it is offered.  This is
            useful to interact with MTAs  that  have  broken
            STARTTLS implementations by simply not using it.

         5.1.4.17.  authinfo

                 The authinfo ruleset is called  when  send-
            mail  tries  to authenticate to another MTA.  It
            should return $# followed by a  list  of  tokens
            that  are  used  for  SMTP  AUTH.  If the return
            value starts with anything else it  is  silently
            ignored.   Each  token is a tagged string of the










SMM:08-70          Sendmail Installation and Operation Guide


            form: "TDstring" (including the quotes), where

                T        Tag which describes the item
                D        Delimiter: ':' simple text follows
                         '=' string is base64 encoded
                string   Value of the item

            Valid values for the tag are:

                U        user (authorization) id
                I        authentication id
                P        password
                R        realm
                M        list of mechanisms delimited by spaces

            If this ruleset is defined, the option  Default-
            AuthInfo  is  ignored  (even if the ruleset does
            not return a ``useful'' result).

         5.1.4.18.  queuegroup

                 The queuegroup ruleset is  used  to  map  a
            recipient  address  to  a queue group name.  The
            input for the ruleset is a recipient address  as
            specified by the SMTP RCPT command.  The ruleset
            should return $# followed by the name of a queue
            group.  If the return value starts with anything
            else it is silently ignored.   See  the  section
            about ``Queue Groups and Queue Directories'' for
            further information.

         5.1.4.19.  greet_pause

                 The greet_pause ruleset is used to  specify
            the  amount  of time to pause before sending the
            initial SMTP 220 greeting.  If  any  traffic  is
            received  during  that pause, an SMTP 554 rejec-
            tion response is given instead of the 220 greet-
            ing  and  all  SMTP commands are rejected during
            that connection.  This helps protect sites  from
            open  proxies  and  SMTP  slammers.  The ruleset
            should return $# followed by the number of  mil-
            liseconds  (thousandths  of  a second) to pause.
            If the return value starts with anything else or
            is  not a number, it is silently ignored.  Note:
            this ruleset is not invoked (and hence the  fea-
            ture is disabled) when the smtps (SMTP over SSL)
            is used, i.e., the s modifier  is  set  for  the
            daemon  via  DaemonPortOptions,  because in this
            case the SSL handshake is performed  before  the
            greeting is sent.












Sendmail Installation and Operation Guide          SMM:08-71


      5.1.5.  IPC mailers

              Some  special processing occurs if the ruleset
         zero resolves to an IPC mailer (that is,  a  mailer
         that  has  "[IPC]" listed as the Path in the M con-
         figuration line.  The host name passed  after  "$@"
         has  MX expansion performed if not delivering via a
         named socket; this looks the name up in DNS to find
         alternate delivery sites.

              The host name can also be provided as a dotted
         quad or an IPv6 address  in  square  brackets;  for
         example:

             [128.32.149.78]

         or

             [IPv6:2002:c0a8:51d2::23f4]

         This  causes direct conversion of the numeric value
         to an IP host address.

              The host name passed in  after  the  "$@"  may
         also  be  a colon-separated list of hosts.  Each is
         separately MX expanded and the results are concate-
         nated  to make (essentially) one long MX list.  The
         intent here is to create "fake" MX records that are
         not published in DNS for private internal networks.

              As a final special case, the host name can  be
         passed in as a text string in square brackets:

             [ucbvax.berkeley.edu]

         This  form  avoids  the  MX mapping.  N.B.: This is
         intended only for situations where you have a  net-
         work  firewall  or  other host that will do special
         processing for all  your  mail,  so  that  your  MX
         record  points  to  a gateway machine; this machine
         could then do direct delivery  to  machines  within
         your  local  domain.   Use of this feature directly
         violates RFC 1123 section 5.3.5: it should  not  be
         used lightly.

   5.2.  D -- Define Macro

           Macros  are named with a single character or with
      a word in  {braces}.   The  names  ``x''  and  ``{x}''
      denote  the  same  macro  for  every  single character
      ``x''.  Single character names may  be  selected  from
      the  entire  ASCII set, but user-defined macros should
      be selected from the set of upper case  letters  only.










SMM:08-72          Sendmail Installation and Operation Guide


      Lower case letters and special symbols are used inter-
      nally.  Long names beginning with a lower case  letter
      or  a  punctuation  character  are reserved for use by
      sendmail, so  user-defined  long  macro  names  should
      begin with an upper case letter.

           The syntax for macro definitions is:

          Dxval

      where  x is the name of the macro (which may be a sin-
      gle character or a word in  braces)  and  val  is  the
      value it should have.  There should be no spaces given
      that do not actually belong in the macro value.

           Macros are interpolated using the  construct  $x,
      where  x  is the name of the macro to be interpolated.
      This interpolation is done when the configuration file
      is read, except in M lines.  The special construct $&x
      can be used in R lines to get deferred  interpolation.

           Conditionals can be specified using the syntax:

          $?x text1 $| text2 $.

      This  interpolates  text1  if  the macro $x is set and
      non-null, and text2 otherwise.  The "else" ($|) clause
      may be omitted.

           The  following  macros  are  defined  and/or used
      internally by sendmail for interpolation  into  argv's
      for  mailers or for other contexts.  The ones marked *
      are information passed  into  sendmail[16],  the  ones
      marked  #  are  information  passed both in and out of
      sendmail, and the unmarked macros are  passed  out  of
      sendmail but are not otherwise used internally.  These
      macros are:

      $a   The origination date in RFC 822 format.  This  is
           extracted from the Date: line.

      $b   The current date in RFC 822 format.

      $c   The  hop count.  This is a count of the number of
           Received: lines plus the value of the -h  command
           line flag.

____________________
   [16]As of version 8.6, all of these macros  have  reason-
able  defaults.  Previous versions required that they be de-
fined.












Sendmail Installation and Operation Guide          SMM:08-73


      $d   The current date in UNIX (ctime) format.

      $e*  (Obsolete;    use    SmtpGreetingMessage   option
           instead.)   The  SMTP  entry  message.   This  is
           printed  out when SMTP starts up.  The first word
           must be the $j macro as  specified  by  RFC  821.
           Defaults  to  "$j Sendmail $v ready at $b".  Com-
           monly redefined to include the configuration ver-
           sion  number,  e.g.,  "$j Sendmail $v/$Z ready at
           $b"

      $f   The envelope sender (from) address.

      $g   The sender address  relative  to  the  recipient.
           For   example,   if  $f  is  "foo",  $g  will  be
           "host!foo",  "foo@host.domain",  or  whatever  is
           appropriate for the receiving mailer.

      $h   The  recipient  host.   This  is set in ruleset 0
           from the $@ field of a parsed address.

      $i   The queue id, e.g., "f344MXxp018717".

      $j#  The "official" domain name for this  site.   This
           is  fully qualified if the full qualification can
           be found.  It must be redefined to be  the  fully
           qualified  domain name if your system is not con-
           figured so that information can find it automati-
           cally.

      $k   The  UUCP node name (from the uname system call).

      $l*  (Obsolete; use UnixFromLine option instead.)  The
           format  of  the  UNIX from line.  Unless you have
           changed the UNIX mailbox format, you  should  not
           change the default, which is "From $g $d".

      $m   The  domain part of the gethostname return value.
           Under normal circumstances, $j is  equivalent  to
           $w.$m.

      $n*  The  name  of  the  daemon  (for error messages).
           Defaults to "MAILER-DAEMON".

      $o*  (Obsolete:  use  OperatorChars  option  instead.)
           The  set  of "operators" in addresses.  A list of
           characters which will be  considered  tokens  and
           which  will  separate  tokens when doing parsing.
           For example, if "@" were in the  $o  macro,  then
           the input "a@b" would be scanned as three tokens:
           "a," "@," and "b."  Defaults to ".:@[]", which is
           the  minimum set necessary to do RFC 822 parsing;
           a richer set of operators  is  ".:%@!/[]",  which










SMM:08-74          Sendmail Installation and Operation Guide


           adds  support  for  UUCP,  the  %-hack, and X.400
           addresses.

      $p   Sendmail's process id.

      $q*  Default format of sender address.  The  $q  macro
           specifies  how an address should appear in a mes-
           sage when it is defaulted.  Defaults  to  "<$g>".
           It is commonly redefined to be "$?x$x <$g>$|$g$."
           or "$g$?x ($x)$.", corresponding to the following
           two formats:

               Eric Allman <eric@CS.Berkeley.EDU>
               eric@CS.Berkeley.EDU (Eric Allman)

           Sendmail  properly quotes names that have special
           characters if the first form is used.

      $r   Protocol used to receive the message.   Set  from
           the  -p  command  line flag or by the SMTP server
           code.

      $s   Sender's host name.  Set from the -p command line
           flag or by the SMTP server code (in which case it
           is set to the EHLO/HELO parameter).

      $t   A numeric representation of the current  time  in
           the  format YYYYMMDDHHmm (4 digit year 1900-9999,
           2 digit month 01-12, 2 digit day 01-31,  2  digit
           hours 00-23, 2 digit minutes 00-59).

      $u   The recipient user.

      $v   The version number of the sendmail binary.

      $w#  The hostname of this site.  This is the root name
           of this host (but see below for caveats).

      $x   The full name of the sender.

      $z   The home directory of the recipient.

      $_   The   validated   sender   address.    See   also
           ${client_resolve}.

      ${addr_type}
           The  type of the address which is currently being
           rewritten.  This macro contains up to three char-
           acters,  the first is either `e' or `h' for enve-
           lope/header address, the second is a  space,  and
           the third is either `s' or `r' for sender/recipi-
           ent address.











Sendmail Installation and Operation Guide          SMM:08-75


      ${alg_bits}
           The maximum keylength (in bits) of the  symmetric
           encryption  algorithm  used for a TLS connection.
           This may be less than  the  effective  keylength,
           which  is  stored in ${cipher_bits}, for ``export
           controlled'' algorithms.

      ${auth_authen}
           The client's authentication credentials as deter-
           mined by authentication (only set if successful).
           The format depends  on  the  mechanism  used,  it
           might  be  just `user', or `user@realm', or some-
           thing similar (SMTP AUTH only).

      ${auth_author}
           The authorization identity, i.e. the AUTH= param-
           eter of the SMTP MAIL command if supplied.

      ${auth_type}
           The  mechanism used for SMTP authentication (only
           set if successful).

      ${auth_ssf}
           The keylength (in bits) of the symmetric  encryp-
           tion  algorithm  used for the security layer of a
           SASL mechanism.

      ${bodytype}
           The message body  type  (7BIT  or  8BITMIME),  as
           determined from the envelope.

      ${cert_issuer}
           The  DN  (distinguished name) of the CA (certifi-
           cate authority) that signed  the  presented  cer-
           tificate (the cert issuer) (STARTTLS only).

      ${cert_md5}
           The MD5 hash of the presented certificate (START-
           TLS only).

      ${cert_subject}
           The DN of the presented certificate  (called  the
           cert subject) (STARTTLS only).

      ${cipher}
           The  cipher  suite used for the connection, e.g.,
           EDH-DSS-DES-CBC3-SHA,  EDH-RSA-DES-CBC-SHA,  DES-
           CBC-MD5, DES-CBC3-SHA (STARTTLS only).

      ${cipher_bits}
           The  effective keylength (in bits) of the symmet-
           ric encryption algorithm used for a  TLS  connec-
           tion.










SMM:08-76          Sendmail Installation and Operation Guide


      ${client_addr}
           The   IP   address  of  the  SMTP  client.   IPv6
           addresses are  tagged  with  "IPv6:"  before  the
           address.  Defined in the SMTP server only.

      ${client_connections}
           The number of open connections in the SMTP server
           for the client IP address.

      ${client_flags}
           The flags specified  by  the  Modifier=  part  of
           ClientPortOptions  where flags are separated from
           each other by spaces and  upper  case  flags  are
           doubled.   That  is,  Modifier=hA  will be repre-
           sented as "h AA"  in  ${client_flags},  which  is
           required for testing the flags in rulesets.

      ${client_name}
           The  host  name  of the SMTP client.  This may be
           the client's bracketed IP address in the  form  [
           nnn.nnn.nnn.nnn     ]     for    IPv4    and    [
           IPv6:nnnn:...:nnnn ] for IPv6 if the client's  IP
           address is not resolvable, or if it is resolvable
           but the  IP  address  of  the  resolved  hostname
           doesn't  match  the original IP address.  Defined
           in   the   SMTP   server    only.     See    also
           ${client_resolve}.

      ${client_port}
           The  port  number of the SMTP client.  Defined in
           the SMTP server only.

      ${client_ptr}
           The result of the PTR lookup for  the  client  IP
           address.     Note:    this   is   the   same   as
           ${client_name} if and only  if  ${client_resolve}
           is OK.  Defined in the SMTP server only.

      ${client_rate}
           The number of incoming connections for the client
           IP address over the time  interval  specified  by
           ConnectionRateWindowSize.

      ${client_resolve}
           Holds   the   result  of  the  resolve  call  for
           ${client_name}.  Possible values are:

               OK        resolved successfully
               FAIL      permanent lookup failure
               FORGED    forward lookup doesn't match reverse lookup
               TEMP      temporary lookup failure

           Defined  in  the  SMTP  server  only.    sendmail










Sendmail Installation and Operation Guide          SMM:08-77


           performs  a  hostname lookup on the IP address of
           the connecting client.  Next the IP addresses  of
           that  hostname  are  looked up.  If the client IP
           address does not appear in that  list,  then  the
           hostname  is  maybe forged.  This is reflected as
           the value FORGED  for  ${client_resolve}  and  it
           also shows up in $_ as "(may be forged)".

      ${cn_issuer}
           The  CN  (common  name) of the CA that signed the
           presented certificate (STARTTLS only).

      ${cn_subject}
           The CN (common name) of the presented certificate
           (STARTTLS only).

      ${currHeader}
           Header value as quoted string (possibly truncated
           to MAXNAME).  This macro  is  only  available  in
           header check rulesets.

      ${daemon_addr}
           The  IP  address  the  daemon is listening on for
           connections.

      ${daemon_family}
           The network family if  the  daemon  is  accepting
           network  connections.   Possible  values  include
           "inet", "inet6", "iso", "ns", "x.25"

      ${daemon_flags}
           The flags for the daemon as specified by the Mod-
           ifier=  part  of  DaemonPortOptions  whereby  the
           flags are separated from each  other  by  spaces,
           and upper case flags are doubled.  That is, Modi-
           fier=Ea will be represented as "EE a"  in  ${dae-
           mon_flags},  which  is  required  for testing the
           flags in rulesets.

      ${daemon_info}
           Some information about a daemon as a text string.
           For example, "SMTP+queueing@00:30:00".

      ${daemon_name}
           The  name  of  the  daemon from DaemonPortOptions
           Name= suboption.  If this suboption is  not  set,
           "Daemon#", where # is the daemon number, is used.

      ${daemon_port}
           The port the daemon is accepting  connection  on.
           Unless  DaemonPortOptions  is set, this will most
           likely be "25".











SMM:08-78          Sendmail Installation and Operation Guide


      ${deliveryMode}
           The current delivery mode sendmail is using.   It
           is initially set to the value of the DeliveryMode
           option.

      ${envid}
           The envelope  id  parameter  (ENVID=)  passed  to
           sendmail as part of the envelope.

      ${hdrlen}
           The length of the header value which is stored in
           ${currHeader} (before possible  truncation).   If
           this  value  is  greater than or equal to MAXNAME
           the header has been truncated.

      ${hdr_name}
           The name of the header field for which  the  cur-
           rent  header check ruleset has been called.  This
           is useful for a default header check  ruleset  to
           get  the  name  of  the header; the macro is only
           available in header check rulesets.

      ${if_addr}
           The IP address of the interface  of  an  incoming
           connection  unless  it  is  in  the loopback net.
           IPv6 addresses are tagged with "IPv6:" before the
           address.

      ${if_addr_out}
           The  IP  address  of the interface of an outgoing
           connection unless it  is  in  the  loopback  net.
           IPv6 addresses are tagged with "IPv6:" before the
           address.

      ${if_family}
           The IP family of the  interface  of  an  incoming
           connection unless it is in the loopback net.

      ${if_family_out}
           The  IP  family  of  the interface of an outgoing
           connection unless it is in the loopback net.

      ${if_name}
           The hostname associated with the interface of  an
           incoming  connection.  This macro can be used for
           SmtpGreetingMessage  and  HReceived  for  virtual
           hosting.  For example:

               O SmtpGreetingMessage=$?{if_name}${if_name}$|$j$. MTA


      ${if_name_out}
           The   name   of  the  interface  of  an  outgoing










Sendmail Installation and Operation Guide          SMM:08-79


           connection.

      ${load_avg}
           The current load average.

      ${mail_addr}
           The address part of the resolved  triple  of  the
           address given for the SMTP MAIL command.  Defined
           in the SMTP server only.

      ${mail_host}
           The host from the resolved triple of the  address
           given  for the SMTP MAIL command.  Defined in the
           SMTP server only.

      ${mail_mailer}
           The  mailer  from  the  resolved  triple  of  the
           address given for the SMTP MAIL command.  Defined
           in the SMTP server only.

      ${msg_id}
           The value of the Message-Id: header.

      ${msg_size}
           The value of the SIZE= parameter,  i.e.,  usually
           the  size  of the message (in an ESMTP dialogue),
           before the message has been collected, thereafter
           the message size as computed by sendmail (and can
           be used in check_compat).

      ${nbadrcpts}
           The number of bad recipients for  a  single  mes-
           sage.

      ${nrcpts}
           The  number  of validated recipients for a single
           message.  Note: since recipient  validation  hap-
           pens  after check_rcpt has been called, the value
           in this ruleset is one less than  what  might  be
           expected.

      ${ntries}
           The number of delivery attempts.

      ${opMode}
           The current operation mode (from the -b flag).

      ${quarantine}
           The  quarantine reason for the envelope, if it is
           quarantined.

      ${queue_interval}
           The queue run interval given by the -q flag.  For










SMM:08-80          Sendmail Installation and Operation Guide


           example,  -q30m  would  set  ${queue_interval} to
           "00:30:00".

      ${rcpt_addr}
           The address part of the resolved  triple  of  the
           address given for the SMTP RCPT command.  Defined
           in the SMTP server only after a RCPT command.

      ${rcpt_host}
           The host from the resolved triple of the  address
           given  for the SMTP RCPT command.  Defined in the
           SMTP server only after a RCPT command.

      ${rcpt_mailer}
           The  mailer  from  the  resolved  triple  of  the
           address given for the SMTP RCPT command.  Defined
           in the SMTP server only after a RCPT command.

      ${server_addr}
           The address of the server of the current outgoing
           SMTP  connection.  For LMTP delivery the macro is
           set to the name of the mailer.

      ${server_name}
           The name of the server of  the  current  outgoing
           SMTP or LMTP connection.

      ${time}
           The  output  of  the  time(3) function, i.e., the
           number of seconds since 0  hours,  0  minutes,  0
           seconds,  January  1, 1970, Coordinated Universal
           Time (UTC).

      ${tls_version}
           The TLS/SSL  version  used  for  the  connection,
           e.g., TLSv1, SSLv3, SSLv2; defined after STARTTLS
           has been used.

      ${total_rate}
           The total number of incoming connections over the
           time  interval specified by ConnectionRateWindow-
           Size.

      ${verify}
           The result of the verification of  the  presented
           cert;  only defined after STARTTLS has been used.
           Possible values are:
















Sendmail Installation and Operation Guide          SMM:08-81


               OK           verification succeeded.
               NO           no cert presented.
               NOT          no cert requested.
               FAIL         cert presented but could not be verified,
                            e.g., the signing CA is missing.
               NONE         STARTTLS has not been performed.
               TEMP         temporary error occurred.
               PROTOCOL     some protocol error occurred.
               SOFTWARE     STARTTLS handshake failed,
                            which is a fatal error for this session,
                            the e-mail will be queued.


           There are three types of dates that can be  used.
      The  $a and $b macros are in RFC 822 format; $a is the
      time as extracted from the "Date:" line of the message
      (if  there  was  one),  and $b is the current date and
      time (used for postmarks).   If  no  "Date:"  line  is
      found  in  the incoming message, $a is set to the cur-
      rent time also.  The $d macro is equivalent to the  $b
      macro in UNIX (ctime) format.

           The macros $w, $j, and $m are set to the identity
      of this host.  Sendmail tries to find the fully quali-
      fied name of the host if at all possible; it does this
      by calling gethostname(2) to get the current  hostname
      and  then  passing  that  to gethostbyname(3) which is
      supposed to return the canonical version of that  host
      name.[17]  Assuming  this  is successful, $j is set to
      the fully qualified name and $m is set to  the  domain
      part  of  the  name  (everything after the first dot).
      The $w macro is set  to  the  first  word  (everything
      before  the first dot) if you have a level 5 or higher
      configuration file; otherwise, it is set to  the  same
      value as $j.  If the canonification is not successful,
      it is imperative that the config file set  $j  to  the
      fully qualified domain name[18].

           The  $f  macro  is the id of the sender as origi-
      nally determined; when mailing to a specific host  the
      $g  macro is set to the address of the sender relative
      to the recipient.  For example, if  I  send  to  "bol-
      lard@matisse.CS.Berkeley.EDU"  from  the machine "van-
      gogh.CS.Berkeley.EDU" the $f macro will be "eric"  and
      the $g macro will be "eric@vangogh.CS.Berkeley.EDU."
____________________
   [17]For example, on some systems gethostname might return
"foo" which would be mapped to "foo.bar.com"  by  gethostby-
name.
   [18]Older  versions  of  sendmail didn't pre-define $j at
all, so up until 8.6, config files always had to define  $j.












SMM:08-82          Sendmail Installation and Operation Guide


           The  $x  macro  is  set  to  the full name of the
      sender.  This can be determined in several  ways.   It
      can  be passed as flag to sendmail.  It can be defined
      in the NAME environment variable.  The third choice is
      the value of the "Full-Name:" line in the header if it
      exists, and the fourth choice is the comment field  of
      a "From:" line.  If all of these fail, and if the mes-
      sage is being originated locally,  the  full  name  is
      looked up in the /etc/passwd file.

           When  sending,  the $h, $u, and $z macros get set
      to the host, user, and home directory  (if  local)  of
      the  recipient.  The first two are set from the $@ and
      $: part of the rewriting rules, respectively.

           The $p and $t macros are used  to  create  unique
      strings  (e.g.,  for the "Message-Id:" field).  The $i
      macro is set to the queue id on this host; if put into
      the  timestamp  line  it  can  be extremely useful for
      tracking messages.  The $v macro is set to be the ver-
      sion number of sendmail; this is normally put in time-
      stamps and has been proven extremely useful for debug-
      ging.

           The $c field is set to the "hop count," i.e., the
      number of times this message has been processed.  This
      can  be  determined by the -h flag on the command line
      or by counting the timestamps in the message.

           The $r and $s fields are set to the protocol used
      to communicate with sendmail and the sending hostname.
      They can be set together using  the  -p  command  line
      flag or separately using the -M or -oM flags.

           The  $_  is  set to a validated sender host name.
      If the sender is running an RFC 1413  compliant  IDENT
      server  and the receiver has the IDENT protocol turned
      on, it will include the user name on that host.

           The    ${client_name},    ${client_addr},     and
      ${client_port}  macros  are  set to the name, address,
      and port number of the SMTP  client  who  is  invoking
      sendmail  as  a  server.   These  can  be  used in the
      check_* rulesets (using  the  $&  deferred  evaluation
      form, of course!).

   5.3.  C and F -- Define Classes

           Classes of phrases may be defined to match on the
      left hand side of rewriting rules, where a "phrase" is
      a  sequence  of characters that does not contain space
      characters.  For example a class of  all  local  names
      for  this  site  might  be created so that attempts to










Sendmail Installation and Operation Guide          SMM:08-83


      send to oneself can be eliminated.  These  can  either
      be  defined directly in the configuration file or read
      in from another file.  Classes are named as  a  single
      letter  or  a word in {braces}.  Class names beginning
      with lower case letters  and  special  characters  are
      reserved  for  system  use.  Classes defined in config
      files may be given names from the set  of  upper  case
      letters  for  short  names  or beginning with an upper
      case letter for long names.

           The syntax is:

          Ccphrase1 phrase2...
          Fcfile
          Fc|program
          Fc[mapkey]@mapclass:mapspec

      The first form defines the class c to match any of the
      named  words.  If phrase1 or phrase2 is another class,
      e.g., $=S, the contents of class S are added to  class
      c.   It  is  permissible  to split them among multiple
      lines; for example, the two forms:

          CHmonet ucbmonet

      and

          CHmonet
          CHucbmonet

      are equivalent.  The ``F'' forms read the elements  of
      the class c from the named file, program, or map spec-
      ification.  Each element should be listed on  a  sepa-
      rate  line.   To  specify an optional file, use ``-o''
      between the class name and the file name, e.g.,

          Fc -o /path/to/file

      If the file can't be used, sendmail will not  complain
      but  silently  ignore  it.   The map form should be an
      optional map key, an at sign, and a map class followed
      by the specification for that map.  Examples include:

          F{VirtHosts}@ldap:-k (&(objectClass=virtHosts)(host=*)) -v host
          F{MyClass}foo@hash:/etc/mail/classes

      will  fill  the  class  $={VirtHosts} from an LDAP map
      lookup and $={MyClass} from a hash database map lookup
      of  the foo.  There is also a built-in schema that can
      be accessed by only specifying:

          F{ClassName}@LDAP











SMM:08-84          Sendmail Installation and Operation Guide


      This will tell sendmail to use the default schema:

          -k (&(objectClass=sendmailMTAClass)
               (sendmailMTAClassName=ClassName)
               (|(sendmailMTACluster=${sendmailMTACluster})
                 (sendmailMTAHost=$j)))
          -v sendmailMTAClassValue

      Note that the lookup is only  done  when  sendmail  is
      initially started.

           Elements  of  classes  can  be  accessed in rules
      using $= or $~.  The $~ (match entries not  in  class)
      only  matches a single word; multi-word entries in the
      class are ignored in this context.

           Some classes have internal meaning to sendmail:

      $=e  contains the Content-Transfer-Encodings that  can
           be 8->7 bit encoded.  It is predefined to contain
           "7bit", "8bit", and "binary".

      $=k  set to be the same as $k, that is, the UUCP  node
           name.

      $=m  set  to  the set of domains by which this host is
           known, initially just $m.

      $=n  can be set to the set of MIME body types that can
           never be eight to seven bit encoded.  It defaults
           to "multipart/signed".  Message types "message/*"
           and  "multipart/*"  are  never  encoded directly.
           Multipart  messages  are  always  handled  recur-
           sively.   The  handling of message/* messages are
           controlled by class $=s.

      $=q  A set of Content-Types that will never be encoded
           as  base64 (if they have to be encoded, they will
           be encoded as  quoted-printable).   It  can  have
           primary  types (e.g., "text") or full types (such
           as "text/plain").  The class  is  initialized  to
           have "text/plain" only.

      $=s  contains  the set of subtypes of message that can
           be treated recursively.  By default  it  contains
           only "rfc822".  Other "message/*" types cannot be
           8->7 bit encoded.  If a message containing  eight
           bit  data  is  sent to a seven bit host, and that
           message cannot be encoded  into  seven  bits,  it
           will be stripped to 7 bits.

      $=t  set to the set of trusted users by the T configu-
           ration line.  If you want to read  trusted  users










Sendmail Installation and Operation Guide          SMM:08-85


           from a file, use Ft/file/name.

      $=w  set to be the set of all names this host is known
           by.  This can be used to match local hostnames.

      $={persistentMacros}
           set to the macros that  should  be  saved  across
           queue  runs.   Care  should  be taken when adding
           macro names to this class.

           Sendmail can be  compiled  to  allow  a  scanf(3)
      string  on  the  F  line.  This lets you do simplistic
      parsing of text files.  For example, to read  all  the
      user  names  in  your  system  /etc/passwd file into a
      class, use

          FL/etc/passwd %[^:]

      which reads every line up to the first colon.

   5.4.  M -- Define Mailer

           Programs and interfaces to mailers are defined in
      this line.  The format is:

          Mname, {field=value}*

      where  name is the name of the mailer (used internally
      only) and the "field=name" pairs define attributes  of
      the mailer.  Fields are:

          Path      The pathname of the mailer
          Flags     Special flags for this mailer
          Sender    Rewriting set(s) for sender addresses
          Recipient Rewriting set(s) for recipient addresses
          recipientsMaximum number of recipients per connection
          Argv      An argument vector to pass to this mailer
          Eol       The end-of-line string for this mailer
          Maxsize   The maximum message length to this mailer
          maxmessagesThe maximum message deliveries per connection
          Linelimit The maximum line length in the message body
          Directory The working directory for the mailer
          Userid    The default user and group id to run as
          Nice      The nice(2) increment for the mailer
          Charset   The default character set for 8-bit characters
          Type      Type information for DSN diagnostics
          Wait      The maximum time to wait for the mailer
          QueuegroupThe default queue group for the mailer
          /         The root directory for the mailer

      Only  the first character of the field name is checked
      (it's case-sensitive).











SMM:08-86          Sendmail Installation and Operation Guide


           The following flags may  be  set  in  the  mailer
      description.   Any  other  flags may be used freely to
      conditionally assign headers to messages destined  for
      particular  mailers.   Flags  marked  with  *  are not
      interpreted by the sendmail binary; these are the con-
      ventionally  used to correlate to the flags portion of
      the H line.  Flags marked with # apply to the  mailers
      for the sender address rather than the usual recipient
      mailers.

      a   Run Extended SMTP  (ESMTP)  protocol  (defined  in
          RFCs 1869, 1652, and 1870).  This flag defaults on
          if the SMTP greeting  message  includes  the  word
          "ESMTP".

      A   Look  up  the  user (address) part of the resolved
          mailer triple, in the  alias  database.   Normally
          this is only set for local mailers.

      b   Force  a blank line on the end of a message.  This
          is intended to work around some stupid versions of
          /bin/mail  that  require  a blank line, but do not
          provide it themselves.  It would not  normally  be
          used on network mail.

      B   Strip  leading backslashes (\) off of the address;
          this is a subset of the  functionality  of  the  s
          flag.

      c   Do not include comments in addresses.  This should
          only be used if you have to work around  a  remote
          mailer  that  gets  confused  by  comments.   This
          strips addresses of the form "Phrase <address>" or
          "address (Comment)" down to just "address".

      C#  If  mail  is received from a mailer with this flag
          set, any addresses in the header that do not  have
          an  at sign ("@") after being rewritten by ruleset
          three will have  the  "@domain"  clause  from  the
          sender  envelope  address  tacked on.  This allows
          mail with headers of the form:

              From: usera@hosta
              To: userb@hostb, userc

          to be rewritten as:

              From: usera@hosta
              To: userb@hostb, userc@hosta

          automatically.  However, it  doesn't  really  work
          reliably.











Sendmail Installation and Operation Guide          SMM:08-87


      d   Do not include angle brackets around route-address
          syntax addresses.  This is useful on mailers  that
          are  going to pass addresses to a shell that might
          interpret angle brackets as I/O redirection.  How-
          ever,  it  does  not  protect  against other shell
          metacharacters.  Therefore, passing addresses to a
          shell should not be considered secure.

      D*  This mailer wants a "Date:" header line.

      e   This  mailer is expensive to connect to, so try to
          avoid connecting normally; any  necessary  connec-
          tion  will  occur  during  a  queue run.  See also
          option HoldExpensive.

      E   Escape lines beginning with "From " in the message
          with a `>' sign.

      f   The  mailer wants a -f from flag, but only if this
          is a network forward operation (i.e.,  the  mailer
          will  give an error if the executing user does not
          have special permissions).

      F*  This mailer wants a "From:" header line.

      g   Normally,  sendmail  sends  internally   generated
          email (e.g., error messages) using the null return
          address as required by RFC  1123.   However,  some
          mailers  don't  accept  a null return address.  If
          necessary, you can set the g flag to prevent send-
          mail  from  obeying  the standards; error messages
          will be sent as from the MAILER-DAEMON  (actually,
          the value of the $n macro).

      h   Upper  case should be preserved in host names (the
          $@ portion of the  mailer  triplet  resolved  from
          ruleset 0) for this mailer.

      i   Do  User  Database  rewriting  on  envelope sender
          address.

      I   This mailer will be speaking SMTP to another send-
          mail  --  as such it can use special protocol fea-
          tures.  This flag should not be  used  except  for
          debugging  purposes  because  it uses VERB as SMTP
          command.

      j   Do User Database rewriting on recipients  as  well
          as senders.

      k   Normally  when  sendmail  connects  to  a host via
          SMTP, it checks to make sure that this isn't acci-
          dently  the  same  host  name  as  might happen if










SMM:08-88          Sendmail Installation and Operation Guide


          sendmail is misconfigured or if a  long-haul  net-
          work interface is set in loopback mode.  This flag
          disables the loopback check.  It  should  only  be
          used under very unusual circumstances.

      K   Currently unimplemented.  Reserved for chunking.

      l   This mailer is local (i.e., final delivery will be
          performed).

      L   Limit the line lengths as specified  in  RFC  821.
          This  deprecated  option should be replaced by the
          L= mail declaration.  For historic reasons, the  L
          flag also sets the 7 flag.

      m   This mailer can send to multiple users on the same
          host in one transaction.  When a $u  macro  occurs
          in  the  argv  part of the mailer definition, that
          field will be repeated as necessary for all quali-
          fying users.  Removing this flag can defeat dupli-
          cate supression on a remote site as each recipient
          is sent in a separate transaction.

      M*  This mailer wants a "Message-Id:" header line.

      n   Do  not  insert  a  UNIX-style  "From" line on the
          front of the message.

      o   Always run as the owner of the recipient  mailbox.
          Normally  sendmail  runs as the sender for locally
          generated mail or as "daemon" (actually, the  user
          specified in the u option) when delivering network
          mail.  The normal behavior  is  required  by  most
          local  mailers,  which will not allow the envelope
          sender address to be set unless the mailer is run-
          ning  as  daemon.   This  flag is ignored if the S
          flag is set.

      p   Use the route-addr style reverse-path in the  SMTP
          "MAIL  FROM:"  command rather than just the return
          address; although this is required in RFC 821 sec-
          tion  3.1, many hosts do not process reverse-paths
          properly.  Reverse-paths are  officially  discour-
          aged by RFC 1123.

      P*  This mailer wants a "Return-Path:" line.

      q   When  an  address  that resolves to this mailer is
          verified  (SMTP  VRFY   command),   generate   250
          responses  instead  of  252  responses.  This will
          imply that the address is local.












Sendmail Installation and Operation Guide          SMM:08-89


      r   Same as f, but sends a -r flag.

      R   Open  SMTP  connections  from  a  "secure"   port.
          Secure  ports  aren't  (secure, that is) except on
          UNIX machines, so it is  unclear  that  this  adds
          anything.   sendmail must be running as root to be
          able to use this flag.

      s   Strip quote  characters  ("  and  \)  off  of  the
          address before calling the mailer.

      S   Don't  reset the userid before calling the mailer.
          This would be used in a secure  environment  where
          sendmail ran as root.  This could be used to avoid
          forged addresses.  If the U= field is also  speci-
          fied, this flag causes the effective user id to be
          set to that user.

      u   Upper case should be preserved in user  names  for
          this  mailer.   Standards  require preservation of
          case in the local part of  addresses,  except  for
          those   address  for  which  your  system  accepts
          responsibility.  RFC 2142 provides a long list  of
          addresses  which  should  be case insensitive.  If
          you use this flag, you may be violating RFC  2142.
          Note  that  postmaster is always treated as a case
          insensitive address regardless of this flag.

      U   This mailer wants UUCP-style "From" lines with the
          ugly "remote from <host>" on the end.

      w   The  user  must  have  a  valid  account  on  this
          machine, i.e., getpwnam must succeed.  If not, the
          mail  is  bounced.   See  also the MailBoxDatabase
          option.  This is required to get ".forward"  capa-
          bility.

      W   Ignore long term host status information (see Sec-
          tion "Persistent Host Status Information").

      x*  This mailer wants a "Full-Name:" header line.

      X   This mailer wants to use the hidden dot  algorithm
          as  specified  in  RFC  821;  basically,  any line
          beginning with  a  dot  will  have  an  extra  dot
          prepended (to be stripped at the other end).  This
          insures that lines in the message containing a dot
          will not terminate the message prematurely.

      z   Run  Local  Mail  Transfer Protocol (LMTP) between
          sendmail and the local mailer.  This is a  variant
          on  SMTP  defined in RFC 2033 that is specifically
          designed for delivery to a local mailbox.










SMM:08-90          Sendmail Installation and Operation Guide


      Z   Apply DialDelay (if set) to this mailer.

      0   Don't look  up  MX  records  for  hosts  sent  via
          SMTP/LMTP.  Do not apply FallbackMXhost either.

      1   Don't  send null characters ('\0') to this mailer.

      2   Don't use ESMTP even if offered;  this  is  useful
          for  broken  systems  that offer ESMTP but fail on
          EHLO (without recovering when HELO is tried next).

      3   Extend  the  list  of  characters converted to =XX
          notation when converting  to  Quoted-Printable  to
          include those that don't map cleanly between ASCII
          and EBCDIC.  Useful if you have IBM mainframes  on
          site.

      5   If no aliases are found for this address, pass the
          address through ruleset 5 for  possible  alternate
          resolution.   This is intended to forward the mail
          to an alternate delivery spot.

      6   Strip headers to seven bits.

      7   Strip all output  to  seven  bits.   This  is  the
          default  if the L flag is set.  Note that clearing
          this option is not sufficient to  get  full  eight
          bit data passed through sendmail.  If the 7 option
          is set, this is essentially always set, since  the
          eighth  bit was stripped on input.  Note that this
          option will only impact messages that didn't  have
          8->7 bit MIME conversions performed.

      8   If set, it is acceptable to send eight bit data to
          this mailer; the usual attempt to do 8->7 bit MIME
          conversions will be bypassed.

      9   If  set,  do  limited  7->8  bit MIME conversions.
          These conversions are limited to text/plain  data.

      :   Check  addresses to see if they begin ":include:";
          if  they  do,  convert  them  to  the  "*include*"
          mailer.

      |   Check  addresses  to see if they begin with a `|';
          if they do, convert them to the "prog" mailer.

      /   Check addresses to see if they begin with  a  `/';
          if they do, convert them to the "*file*" mailer.

      @   Look up addresses in the user database.












Sendmail Installation and Operation Guide          SMM:08-91


      %   Do  not attempt delivery on initial recipient of a
          message or on queue runs unless the queued message
          is selected using one of the -qI/-qR/-qS queue run
          modifiers or an ETRN request.

           Configuration files prior to level 6  assume  the
      `A',  `w',  `5', `:', `|', `/', and `@' options on the
      mailer named "local".

           The mailer with the special name "error"  can  be
      used  to  generate  a user error.  The (optional) host
      field is an exit status to be returned, and  the  user
      field is a message to be printed.  The exit status may
      be numeric or one of the values USAGE, NOUSER, NOHOST,
      UNAVAILABLE,  SOFTWARE,  TEMPFAIL, PROTOCOL, or CONFIG
      to return the  corresponding  EX_  exit  code,  or  an
      enhanced error code as described in RFC 1893, Enhanced
      Mail System Status Codes.  For example, the entry:

          $#error $@ NOHOST $: Host unknown in this domain

      on the RHS of a rule will cause the specified error to
      be  generated and the "Host unknown" exit status to be
      returned if the LHS  matches.   This  mailer  is  only
      functional  in  rulesets  0,  5, or one of the check_*
      rulesets.  The host field can also contain the special
      token  quarantine  which instructs sendmail to quaran-
      tine the current message.

           The mailer with the special name "discard" causes
      any  mail  sent  to  it  to be discarded but otherwise
      treated as  though  it  were  successfully  delivered.
      This  mailer  cannot be used in ruleset 0, only in the
      various address checking rulesets.

           The mailer named "local" must be defined in every
      configuration  file.   This  is  used to deliver local
      mail, and is treated specially in several ways.  Addi-
      tionally,  three other mailers named "prog", "*file*",
      and "*include*" may be defined to tune the delivery of
      messages  to  programs,  files,  and  :include:  lists
      respectively.  They default to:

          Mprog, P=/bin/sh, F=lsoDq9, T=DNS/RFC822/X-Unix, A=sh -c $u
          M*file*, P=[FILE], F=lsDFMPEouq9, T=DNS/RFC822/X-Unix, A=FILE $u
          M*include*, P=/dev/null, F=su, A=INCLUDE $u


           Builtin pathnames are [FILE] and [IPC], the  for-
      mer  is  used  for  delivery  to files, the latter for
      delivery via interprocess communication.  For  mailers
      that  use  [IPC]  as pathname the argument vector (A=)
      must start with TCP or FILE for delivery via a TCP  or










SMM:08-92          Sendmail Installation and Operation Guide


      a  Unix  domain  socket.   If  TCP is used, the second
      argument must be the name  of  the  host  to  contact.
      Optionally  a  third argument can be used to specify a
      port, the default is smtp (port 25).  If FILE is used,
      the  second  argument  must  be  the  name of the Unix
      domain socket.

           If the argument vector does not contain  $u  then
      sendmail will speak SMTP (or LMTP if the mailer flag z
      is specified) to the mailer.

           If no Eol field is defined, then the  default  is
      "\r\n" for SMTP mailers and "\n" of others.

           The  Sender  and  Recipient  rewriting  sets  may
      either be a simple ruleset id or may be two ids  sepa-
      rated  by  a  slash; if so, the first rewriting set is
      applied  to  envelope  addresses  and  the  second  is
      applied  to  headers.   Setting any value to zero dis-
      ables corresponding mailer-specific rewriting.

           The Directory is actually a colon-separated  path
      of  directories  to  try.  For example, the definition
      "D=$z:/" first tries to  execute  in  the  recipient's
      home  directory; if that is not available, it tries to
      execute in  the  root  of  the  filesystem.   This  is
      intended  to  be used only on the "prog" mailer, since
      some shells (such as csh) refuse to  execute  if  they
      cannot  read  the  current directory.  Since the queue
      directory is not  normally  readable  by  unprivileged
      users csh scripts as recipients can fail.

           The  Userid  specifies the default user and group
      id  to  run  as,  overriding  the  DefaultUser  option
      (q.v.).   If the S mailer flag is also specified, this
      user and group will be set as the  effective  uid  and
      gid  for the process.  This may be given as user:group
      to set both the user and group id; either  may  be  an
      integer  or  a  symbolic  name  to be looked up in the
      passwd and group files respectively.  If only  a  sym-
      bolic  user  name  is  specified,  the group id in the
      passwd file for that user is used as the group id.

           The Charset field is used when converting a  mes-
      sage  to  MIME;  this is the character set used in the
      Content-Type:  header.   If  this  is  not  set,   the
      DefaultCharset option is used, and if that is not set,
      the value "unknown-8bit" is used.  WARNING: this field
      applies  to  the  sender's mailer, not the recipient's
      mailer.  For example, if the envelope  sender  address
      lists  an address on the local network and the recipi-
      ent is on an external network, the character set  will
      be  set  from the Charset= field for the local network










Sendmail Installation and Operation Guide          SMM:08-93


      mailer, not that of the external network mailer.

           The Type= field sets the type information used in
      MIME  error  messages  as  defined by RFC 1894.  It is
      actually three values separated by slashes:  the  MTA-
      type  (that  is,  the  description  of  how  hosts are
      named), the address type (the  description  of  e-mail
      addresses),  and  the diagnostic type (the description
      of error diagnostic codes).  Each of these must  be  a
      registered  value  or begin with "X-".  The default is
      "dns/rfc822/smtp".

           The m= field specifies the maximum number of mes-
      sages  to  attempt to deliver on a single SMTP or LMTP
      connection.  The default is infinite.

           The r= field  specifies  the  maximum  number  of
      recipients to attempt to deliver in a single envelope.
      It defaults to 100.

           The /= field specifies a new root  directory  for
      the  mailer.   The  path  is  macro  expanded and then
      passed to the "chroot" system call.  The  root  direc-
      tory  is  changed  before  the Directory field is con-
      sulted or the uid is changed.

           The Wait= field specifies  the  maximum  time  to
      wait  for  the mailer to return after sending all data
      to it.  This applies to mailers that have been  forked
      by sendmail.

           The Queuegroup= field specifies the default queue
      group in which received mail should be  queued.   This
      can  be overridden by other means as explained in sec-
      tion ``Queue Groups and Queue Directories''.

   5.5.  H -- Define Header

           The format of  the  header  lines  that  sendmail
      inserts  into  the  message are defined by the H line.
      The syntax of this line is one of the following:

          Hhname: htemplate


          H[?mflags?]hname: htemplate


          H[?${macro}?]hname: htemplate

      Continuation lines in this spec are reflected directly
      into  the  outgoing  message.  The htemplate is macro-
      expanded before insertion into the  message.   If  the










SMM:08-94          Sendmail Installation and Operation Guide


      mflags  (surrounded  by question marks) are specified,
      at least one of the specified flags must be stated  in
      the  mailer definition for this header to be automati-
      cally output.  If a ${macro} (surrounded  by  question
      marks)  is specified, the header will be automatically
      output if the macro is set.   The  macro  may  be  set
      using  any  of the normal methods, including using the
      macro storage map in a ruleset.  If one of these head-
      ers  is  in  the  input  it is reflected to the output
      regardless of these flags or  macros.   Notice:  If  a
      ${macro} is used to set a header, then it is useful to
      add that macro  to  class  $={persistentMacros}  which
      consists  of  the  macros  that should be saved across
      queue runs.

           Some headers have special semantics that will  be
      described later.

           A  secondary  syntax allows validation of headers
      as they are being read.  To enable validation, use:

          HHeader: $>Ruleset
          HHeader: $>+Ruleset

      The indicated Ruleset  is  called  for  the  specified
      Header, and can return $#error to reject or quarantine
      the message or $#discard to discard  the  message  (as
      with   the   other  check_*  rulesets).   The  ruleset
      receives the header field-body as argument, i.e.,  not
      the header field-name; see also ${hdr_name} and ${cur-
      rHeader}.  The  header  is  treated  as  a  structured
      field,  that is, text in parentheses is deleted before
      processing, unless the second form $>+ is used.  Note:
      only  one  ruleset  can  be  associated with a header;
      sendmail will silently ignore multiple entries.

           For example, the configuration lines:

          HMessage-Id: $>CheckMessageId

          SCheckMessageId
          R< $+ @ $+  >$@ OK
          R$*       $#error $: Illegal Message-Id header

      would refuse any message that had a Message-Id: header
      of any of the following forms:

          Message-Id: <>
          Message-Id: some text
          Message-Id: <legal text@domain> extra crud

      A  default  ruleset  that  is called for headers which
      don't have a specific ruleset defined for them can  be










Sendmail Installation and Operation Guide          SMM:08-95


      specified by:

          H*: $>Ruleset

      or

          H*: $>+Ruleset


   5.6.  O -- Set Option

           There  are a number of global options that can be
      set from a configuration  file.   Options  are  repre-
      sented  by  full words; some are also representable as
      single characters for back compatibility.  The  syntax
      of this line is:

          O  option=value

      This  sets option option to be value.  Note that there
      must be a space between the letter `O' and the name of
      the option.  An older version is:

          Oovalue

      where  the  option o is a single character.  Depending
      on the option, value may be a string,  an  integer,  a
      boolean  (with legal values "t", "T", "f", or "F"; the
      default is TRUE), or a time interval.

           All filenames used in options should be  absolute
      paths,  i.e.,  starting  with '/'.  Relative filenames
      most likely cause surprises during  operation  (unless
      otherwise noted).

           The  options supported (with the old, one charac-
      ter names in brackets) are:

      AliasFile=spec, spec, ...
                [A] Specify possible  alias  file(s).   Each
                spec should be in the format ``class: info''
                where class: is  optional  and  defaults  to
                ``implicit''.   Note  that  info is required
                for all  classes  except  "ldap".   For  the
                "ldap"  class,  if  info is not specified, a
                default info value is used as follows:

                    -k (&(objectClass=sendmailMTAAliasObject)
                         (sendmailMTAAliasName=aliases)
                         (|(sendmailMTACluster=${sendmailMTACluster})
                           (sendmailMTAHost=$j))
                         (sendmailMTAKey=%0))
                    -v sendmailMTAAliasValue










SMM:08-96          Sendmail Installation and Operation Guide


                Depending on how sendmail is compiled, valid
                classes  are  "implicit"  (search  through a
                compiled-in list of alias  file  types,  for
                back  compatibility),  "hash"  (if  NEWDB is
                specified), "btree" (if NEWDB is specified),
                "dbm" (if NDBM is specified), "stab" (inter-
                nal symbol table -- not normally used unless
                you   have   no   other   database  lookup),
                "sequence" (use a sequence  of  maps  previ-
                ously declared), "ldap" (if LDAPMAP is spec-
                ified), or "nis" (if NIS is specified).   If
                a  list  of  specs  are  provided,  sendmail
                searches them in order.

      AliasWait=timeout
                [a]  If  set,  wait  up  to  timeout  (units
                default  to  minutes)  for an "@:@" entry to
                exist in the alias database before  starting
                up.   If  it  does not appear in the timeout
                interval issue a warning.

      AllowBogusHELO
                [no short name] If set, allow HELO SMTP com-
                mands  that don't include a host name.  Set-
                ting this violates RFC 1123  section  5.2.5,
                but  is  necessary to interoperate with sev-
                eral SMTP clients.  If there is a value,  it
                is still checked for legitimacy.

      AuthMaxBits=N
                [no short name] Limit the maximum encryption
                strength for the security layer in SMTP AUTH
                (SASL).  Default  is  essentially unlimited.
                This allows to turn off  additional  encryp-
                tion in SASL if STARTTLS is already encrypt-
                ing the communication, because the  existing
                encryption  strength  is  taken into account
                when choosing an algorithm for the  security
                layer.  For example, if STARTTLS is used and
                the symmetric cipher is 3DES, then  the  the
                keylength  (in  bits) is 168.  Hence setting
                AuthMaxBits to 168 will disable any  encryp-
                tion in SASL.

      AuthMechanisms
                [no short name] List of authentication mech-
                anisms for AUTH (separated by spaces).   The
                advertised list of authentication mechanisms
                will be the intersection of  this  list  and
                the  list  of available mechanisms as deter-
                mined by the Cyrus SASL library.  If  START-
                TLS  is  active,  EXTERNAL  will be added to
                this list.   In  that  case,  the  value  of










Sendmail Installation and Operation Guide          SMM:08-97


                {cert_subject} is used as authentication id.

      AuthOptions
                [no short name] List  of  options  for  SMTP
                AUTH  consisting  of  single characters with
                intervening white space or commas.

                    A   Use the AUTH= parameter for the MAIL FROM
                        command only when authentication succeeded.
                        This can be used as a workaround for broken
                        MTAs that do not implement RFC 2554 correctly.
                    a   protection from active (non-dictionary) attacks
                        during authentication exchange.
                    c   require mechanisms which pass client credentials,
                        and allow mechanisms which can pass credentials
                        to do so.
                    d   don't permit mechanisms susceptible to passive
                        dictionary attack.
                    f   require forward secrecy between sessions
                        (breaking one won't help break next).
                    m   require mechanisms which provide mutual authentication
                        (only available if using Cyrus SASL v2 or later).
                    p   don't permit mechanisms susceptible to simple
                        passive attack (e.g., PLAIN, LOGIN), unless a
                        security layer is active.
                    y   don't permit mechanisms that allow anonymous login.

                The first option applies to  sendmail  as  a
                client, the others to a server.  Example:

                    O AuthOptions=p,y

                would  disallow  ANONYMOUS as AUTH mechanism
                and would allow PLAIN and LOGIN  only  if  a
                security  layer (e.g., provided by STARTTLS)
                is already active.  The  options  'a',  'c',
                'd',  'f',  'p', and 'y' refer to properties
                of the selected SASL  mechanisms.   Explana-
                tions  of  these  properties can be found in
                the Cyrus SASL documentation.

      AuthRealm [no short  name]  The  authentication  realm
                that  is  passed  to the Cyrus SASL library.
                If no realm is specified, $j is used.

      BadRcptThrottle=N
                [no short name] If  set  and  the  specified
                number of recipients in a single SMTP trans-
                action have been  rejected,  sleep  for  one
                second after each subsequent RCPT command in
                that transaction.












SMM:08-98          Sendmail Installation and Operation Guide


      BlankSub=c
                [B] Set the blank substitution character  to
                c.    Unquoted   spaces   in  addresses  are
                replaced by  this  character.   Defaults  to
                space (i.e., no change is made).

      CACertPath
                [no  short name] Path to directory with cer-
                tificates of CAs.  This directory  directory
                must  contain the hashes of each CA certifi-
                cate as filenames (or as links to them).

      CACertFile
                [no short name] File containing one or  more
                CA  certificates; see section about STARTTLS
                for more information.

      CheckAliases
                [n]  Validate  the  RHS  of   aliases   when
                rebuilding the alias database.

      CheckpointInterval=N
                [C]  Checkpoints  the queue every N (default
                10) addresses sent.  If your system  crashes
                during  delivery  to a large list, this pre-
                vents retransmission to any but the  last  N
                recipients.

      ClassFactor=fact
                [z]  The  indicated  factor is multiplied by
                the message class (determined by the  Prece-
                dence:  field  in  the user header and the P
                lines in the configuration  file)  and  sub-
                tracted  from  the priority.  Thus, messages
                with a higher  Priority:  will  be  favored.
                Defaults to 1800.

      ClientCertFile
                [no short name] File containing the certifi-
                cate of the client, i.e.,  this  certificate
                is  used  when  sendmail acts as client (for
                STARTTLS).

      ClientKeyFile
                [no short name] File containing the  private
                key belonging to the client certificate (for
                STARTTLS if sendmail runs as client).

      ClientPortOptions=options
                [O] Set client SMTP  options.   The  options
                are  key=value  pairs  separated  by commas.
                Known keys are:











Sendmail Installation and Operation Guide          SMM:08-99


                    Port      Name/number of source port for connection (defaults to any free port)
                    Addr      Address mask (defaults INADDR_ANY)
                    Family    Address family (defaults to INET)
                    SndBufSizeSize of TCP send buffer
                    RcvBufSizeSize of TCP receive buffer
                    Modifier  Options (flags) for the client

                The Address mask may be a numeric address in
                dot  notation  or  a network name.  Modifier
                can be the following character:

                    h         use name of interface for HELO command
                    A         don't use AUTH when sending e-mail
                    S         don't use STARTTLS when sending e-mail

                If ``h'' is set, the name  corresponding  to
                the outgoing interface address (whether cho-
                sen via  the  Connection  parameter  or  the
                default)  is used for the HELO/EHLO command.
                However, the name  must  not  start  with  a
                square  bracket and it must contain at least
                one dot.  This is a simple test whether  the
                name  is not an IP address (in square brack-
                ets) but a qualified  hostname.   Note  that
                multiple   ClientPortOptions   settings  are
                allowed in order to give settings  for  each
                protocol  family  (e.g., one for Family=inet
                and one for  Family=inet6).   A  restriction
                placed  on  one family only affects outgoing
                connections on that particular family.

      ColonOkInAddr
                [no short name] If set, colons  are  accept-
                able     in    e-mail    addresses    (e.g.,
                "host:user").  If not set,  colons  indicate
                the  beginning  of a RFC 822 group construct
                ("groupname:  member1,  member2,  ...   mem-
                berN;").   Doubled colons are always accept-
                able ("nodename::user")  and  proper  route-
                addr       nesting       is       understood
                ("<@relay:user@host>").   Furthermore,  this
                option defaults on if the configuration ver-
                sion level is less than 6 (for back compati-
                bility).   However,  it must be off for full
                compatibility with RFC 822.

      ConnectionCacheSize=N
                [k] The maximum number of  open  connections
                that  will be cached at a time.  The default
                is one.  This  delays  closing  the  current
                connection  until  either this invocation of
                sendmail needs to connect to another host or
                it  terminates.  Setting it to zero defaults










SMM:08-100         Sendmail Installation and Operation Guide


                to the old behavior,  that  is,  connections
                are closed immediately.  Since this consumes
                file  descriptors,  the   connection   cache
                should  be kept small: 4 is probably a prac-
                tical maximum.

      ConnectionCacheTimeout=timeout
                [K] The maximum amount of time a cached con-
                nection  will  be  permitted to idle without
                activity.  If this  time  is  exceeded,  the
                connection   is  immediately  closed.   This
                value should be small (on the order  of  ten
                minutes).   Before  sendmail  uses  a cached
                connection, it always sends a  RSET  command
                to  check  the connection; if this fails, it
                reopens the connection.  This keeps your end
                from  failing  if  the  other end times out.
                The point of this option is  to  be  a  good
                network  neighbor  and avoid using up exces-
                sive  resources  on  the  other  end.    The
                default is five minutes.

      ConnectOnlyTo=address
                [no short name] This can be used to override
                the connection  address  (for  testing  pur-
                poses).

      ConnectionRateThrottle=N
                [no  short name] If set to a positive value,
                allow no more than N incoming connections in
                a  one  second  period  per daemon.  This is
                intended to flatten out peaks and allow  the
                load  average  checking to cut in.  Defaults
                to zero (no limits).

      ConnectionRateWindowSize=N
                [no short name] Define  the  length  of  the
                interval  for  which  the number of incoming
                connections is maintained.  The  default  is
                60 seconds.

      ControlSocketName=name
                [no  short  name] Name of the control socket
                for daemon management.  A  running  sendmail
                daemon  can be controlled through this named
                socket.   Available  commands   are:   help,
                mstat,  restart,  shutdown, and status.  The
                status command returns the current number of
                daemon  children, the maximum number of dae-
                mon  children,  the  free  disk  space   (in
                blocks) of the queue directory, and the load
                average of the machine expressed as an inte-
                ger.   If not set, no control socket will be










Sendmail Installation and Operation Guide         SMM:08-101


                available.  Solaris  and  pre-4.4BSD  kernel
                users should see the note in sendmail/README
                .

      CRLFile=name
                [no short name] Name of file  that  contains
                certificate  revocation  status,  useful for
                X.509v3   authentication.    CRL    checking
                requires  at  least  OpenSSL  version 0.9.7.
                Note: if a CRLFile is specified but the file
                is unusable, STARTTLS is disabled.

      DHParameters
                File  with DH parameters for STARTTLS.  This
                is only required if a ciphersuite containing
                DSA/DH  is  used.   This  is only for people
                with a good knowledge of TLS, all others can
                ignore this option.

      DaemonPortOptions=options
                [O]  Set server SMTP options.  Each instance
                of DaemonPortOptions leads to an  additional
                incoming  socket.  The options are key=value
                pairs.  Known keys are:

                    Name      User-definable name for the daemon (defaults to "Daemon#")
                    Port      Name/number of listening port (defaults to "smtp")
                    Addr      Address mask (defaults INADDR_ANY)
                    Family    Address family (defaults to INET)
                    InputMailFiltersList of input mail filters for the daemon
                    Listen    Size of listen queue (defaults to 10)
                    Modifier  Options (flags) for the daemon
                    SndBufSizeSize of TCP send buffer
                    RcvBufSizeSize of TCP receive buffer
                    children  maximum number of children per daemon, see MaxDaemonChildren.
                    DeliveryModeDelivery mode per daemon, see DeliveryMode.
                    refuseLA  RefuseLA per daemon
                    delayLA   DelayLA per daemon
                    queueLA   QueueLA per daemon

                The Name key is used for error messages  and
                logging.   The Address mask may be a numeric
                address in dot notation or a  network  name.
                The  Family  key  defaults  to  INET (IPv4).
                IPv6 users who wish to also accept IPv6 con-
                nections  should add additional Family=inet6
                DaemonPortOptions lines.  The  InputMailFil-
                ters key overrides the default list of input
                mail filters listed in the  InputMailFilters
                option.   If multiple input mail filters are
                required, they must be  separated  by  semi-
                colons  (not  commas).   Modifier  can  be a
                sequence (without  any  delimiters)  of  the










SMM:08-102         Sendmail Installation and Operation Guide


                following characters:

                    a         always require authentication
                    b         bind to interface through which mail has been received
                    c         perform hostname canonification (.cf)
                    f         require fully qualified hostname (.cf)
                    s         Run smtps (SMTP over SSL) instead of smtp
                    u         allow unqualified addresses (.cf)
                    A         disable AUTH (overrides 'a' modifier)
                    C         don't perform hostname canonification
                    E         disallow ETRN (see RFC 2476)
                    O         optional; if opening the socket fails ignore it
                    S         don't offer STARTTLS

                That  is,  one way to specify a message sub-
                mission agent  (MSA)  that  always  requires
                authentication is:

                    O DaemonPortOptions=Name=MSA, Port=587, M=Ea

                The  modifiers  that are marked with "(.cf)"
                have only effect in the standard  configura-
                tion  file,  in which they are available via
                ${daemon_flags}.  Notice:  Do  not  use  the
                ``a''  modifier  on a public accessible MTA!
                It should only be used for  a  MSA  that  is
                accessed  by  authorized  users  for initial
                mail submission.  Users must authenticate to
                use  a  MSA which has this option turned on.
                The flags ``c'' and  ``C''  can  change  the
                default  for  hostname canonification in the
                sendmail.cf file.  See the relevant documen-
                tation  for  FEATURE(nocanonify).  The modi-
                fier ``f'' disallows addresses of  the  form
                user@host    unless   they   are   submitted
                directly.  The flag ``u'' allows unqualified
                sender addresses, i.e., those without @host.
                ``b'' forces sendmail to bind to the  inter-
                face  through  which  the  e-mail  has  been
                received for the outgoing connection.  WARN-
                ING:  Use ``b'' only if outgoing mail can be
                routed  through  the  incoming  connection's
                interface  to its destination. No attempt is
                made to catch problems due to a  misconfigu-
                ration  of  this  parameter, use it only for
                virtual hosting where each virtual interface
                can  connect  to  every  possible  location.
                This will also  override  possible  settings
                via  ClientPortOptions.  Note, sendmail will
                listen on a new socket for each occurence of
                the DaemonPortOptions option in a configura-
                tion file.  The modifier ``O'' causes  send-
                mail  to  ignore  a  socket  if  it can't be










Sendmail Installation and Operation Guide         SMM:08-103


                opened.  This applies to failures  from  the
                socket(2) and bind(2) calls.

      DefaultAuthInfo
                [no   short  name]  Filename  that  contains
                default authentication information for  out-
                going  connections.  This  file must contain
                the user id, the authorization id, the pass-
                word (plain text), the realm and the list of
                mechanisms to use on separate lines and must
                be  readable  by  root (or the trusted user)
                only.  If no realm is specified, $j is used.
                If  no  mechanisms  are  specified, the list
                given by AuthMechanisms  is  used.   Notice:
                this   option  is  deprecated  and  will  be
                removed in future  versions.   Moreover,  it
                doesn't work for the MSP since it can't read
                the file (the file must not be  group/world-
                readable  otherwise sendmail will complain).
                Use the authinfo ruleset instead which  pro-
                vides  more  control  over  the usage of the
                data anyway.

      DefaultCharSet=charset
                [no short name]  When  a  message  that  has
                8-bit  characters  but is not in MIME format
                is converted to MIME (see  the  EightBitMode
                option)  a character set must be included in
                the Content-Type:  header.   This  character
                set  is normally set from the Charset= field
                of the mailer descriptor.  If  that  is  not
                set,  the  value of this option is used.  If
                this  option   is   not   set,   the   value
                "unknown-8bit" is used.

      DataFileBufferSize=threshold
                [no short name] Set the threshold, in bytes,
                before  a  memory-based  queue   data   file
                becomes  disk-based.   The  default  is 4096
                bytes.

      DeadLetterDrop=file
                [no short name] Defines the location of  the
                system-wide dead.letter file, formerly hard-
                coded  to  /usr/tmp/dead.letter.   If   this
                option  is  not  set (the default), sendmail
                will not attempt to save  to  a  system-wide
                dead.letter  file  in  the  event  it cannot
                bounce the mail to the user  or  postmaster.
                Instead,  it  will  rename the qf file as it
                has in the past when  the  dead.letter  file
                could not be opened.











SMM:08-104         Sendmail Installation and Operation Guide


      DefaultUser=user:group
                [u]  Set  the  default userid for mailers to
                user:group.  If group is omitted and user is
                a  user  name  (as opposed to a numeric user
                id)  the  default  group   listed   in   the
                /etc/passwd  file  for  that user is used as
                the default group.  Both user and group  may
                be  numeric.   Mailers without the S flag in
                the mailer definition will run as this user.
                Defaults  to  1:1.   The  value  can also be
                given as a symbolic user name.[19]

      DelayLA=LA
                [no short name] When the system load average
                exceeds LA, sendmail will sleep for one sec-
                ond on most SMTP commands and before accept-
                ing connections.

      DeliverByMin=time
                [0] Set minimum time  for  Deliver  By  SMTP
                Service Extension (RFC 2852).  If 0, no time
                is listed, if less than 0, the extension  is
                not offered, if greater than 0, it is listed
                as minimum time for the EHLO keyword  DELIV-
                ERBY.

      DeliveryMode=x
                [d] Deliver in mode x.  Legal modes are:

                    i   Deliver interactively (synchronously)
                    b   Deliver in background (asynchronously)
                    q   Just queue the message (deliver during queue run)
                    d   Defer delivery and all map lookups (deliver during queue run)

                Defaults to ``b'' if no option is specified,
                ``i'' if it is specified but given no  argu-
                ment   (i.e.,   ``Od''   is   equivalent  to
                ``Odi'').  The -v  command  line  flag  sets
                this to i.

      DialDelay=sleeptime
                [no  short name] Dial-on-demand network con-
                nections can see timeouts if a connection is
                opened  before  the call is set up.  If this
                is set to an interval and a connection times
                out  on the first connection being attempted
                sendmail will sleep for this amount of  time
                and try again.  This should give your system
____________________
   [19]The old g option has been combined into the  Default-
User option.












Sendmail Installation and Operation Guide         SMM:08-105


                time to establish  the  connection  to  your
                service provider.  Units default to seconds,
                so "DialDelay=5" uses a five  second  delay.
                Defaults  to  zero  (no  retry).  This delay
                only applies to mailers  which  have  the  Z
                flag set.

      DirectSubmissionModifiers=modifiers
                Defines  ${daemon_flags} for direct (command
                line)  submissions.   If  not  set,   ${dae-
                mon_flags} is either "CC f" if the option -G
                is used or "c u" otherwise.  Note that  only
                the  the  "CC",  "c", "f", and "u" flags are
                checked.

      DontBlameSendmail=option,option,...
                [no short name] In order to  avoid  possible
                cracking   attempts  caused  by  world-  and
                group-writable files and directories,  send-
                mail  does  paranoid  checking  when opening
                most of its support files.  If for some rea-
                son  you absolutely must run with, for exam-
                ple, a group-writable /etc  directory,  then
                you  will have to turn off this checking (at
                the cost of making your system more vulnera-
                ble to attack).  The possible arguments have
                been  described  earlier.   The  details  of
                these  flags  are  described  above.  Use of
                this option is not recommended.

      DontExpandCnames
                [no short name] The standards say  that  all
                host  addresses  used in a mail message must
                be fully canonical.  For  example,  if  your
                host  is  named "Cruft.Foo.ORG" and also has
                an alias of "FTP.Foo.ORG", the  former  name
                must be used at all times.  This is enforced
                during host name canonification ($[  ...  $]
                lookups).  If this option is set, the proto-
                cols are ignored and the  "wrong"  thing  is
                done.   However,  the  IETF is moving toward
                changing this standard, so the behavior  may
                become  acceptable.   Please note that hosts
                downstream may still rewrite the address  to
                be the true canonical name however.

      DontInitGroups
                [no  short name] If set, sendmail will avoid
                using the initgroups(3) call.   If  you  are
                running  NIS,  this causes a sequential scan
                of the groups.byname map,  which  can  cause
                your  NIS server to be badly overloaded in a
                large domain.  The cost of this is that  the










SMM:08-106         Sendmail Installation and Operation Guide


                only  group  found  for  users will be their
                primary  group  (the  one  in  the  password
                file),  which  will make file access permis-
                sions somewhat  more  restrictive.   Has  no
                effect  on  systems  that  don't  have group
                lists.

      DontProbeInterfaces
                [no short name] Sendmail normally finds  the
                names  of  all  interfaces  active  on  your
                machine when it starts  up  and  adds  their
                name to the $=w class of known host aliases.
                If you have a large number of virtual inter-
                faces  or  if  your  DNS inverse lookups are
                slow  this  can  be  time  consuming.   This
                option turns off that probing.  However, you
                will need to be certain to include all vari-
                ant  names  in  the  $=w class by some other
                mechanism.  If  set  to  loopback,  loopback
                interfaces (e.g., lo0) will not be probed.

      DontPruneRoutes
                [R]  Normally,  sendmail  tries to eliminate
                any unnecessary explicit routes when sending
                an error message (as discussed in RFC 1123 S
                5.2.6).  For example, when sending an  error
                message to

                    <@known1,@known2,@known3:user@unknown>

                sendmail      will     strip     off     the
                "@known1,@known2" in order to make the route
                as  direct  as  possible.  However, if the R
                option is set, this will  be  disabled,  and
                the  mail  will be sent to the first address
                in the route, even if  later  addresses  are
                known.  This may be useful if you are caught
                behind a firewall.

      DoubleBounceAddress=error-address
                [no short name]  If  an  error  occurs  when
                sending  an  error  message,  send the error
                report (termed a "double bounce" because  it
                is an error "bounce" that occurs when trying
                to send another error "bounce") to the indi-
                cated   address.    The   address  is  macro
                expanded at the time of  delivery.   If  not
                set, defaults to "postmaster".  If set to an
                empty string, double bounces are dropped.

      EightBitMode=action
                [8] Set handling of eight-bit  data.   There
                are   two  kinds  of  eight-bit  data:  that










Sendmail Installation and Operation Guide         SMM:08-107


                declared as  such  using  the  BODY=8BITMIME
                ESMTP  declaration or the -B8BITMIME command
                line flag, and undeclared 8-bit  data,  that
                is,  input  that  just  happens  to be eight
                bits.  There are three basic operations that
                can  happen:  undeclared  8-bit  data can be
                automatically converted to  8BITMIME,  unde-
                clared  8-bit data can be passed as-is with-
                out conversion to MIME  (``just  send  8''),
                and  declared 8-bit data can be converted to
                7-bits for transmission  to  a  non-8BITMIME
                mailer.  The possible actions are:

                      s Reject undeclared 8-bit data (``strict'')
                      m Convert undeclared 8-bit data to MIME (``mime'')
                      p Pass undeclared 8-bit data (``pass'')

                In all cases properly declared 8BITMIME data
                will be converted to 7BIT as needed.

      ErrorHeader=file-or-message
                [E] Prepend error messages  with  the  indi-
                cated  message.   If it begins with a slash,
                it is assumed to be the pathname of  a  file
                containing  a  message  (this  is the recom-
                mended setting).  Otherwise, it is a literal
                message.   The  error file might contain the
                name, email address, and/or phone number  of
                a  local postmaster who could provide assis-
                tance to end users.  If the option is  miss-
                ing  or  null,  or  if it names a file which
                does not exist or which is not readable,  no
                message is printed.

      ErrorMode=x
                [e]  Dispose  of  errors  using mode x.  The
                values for x are:

                    p   Print error messages (default)
                    q   No messages, just give exit status
                    m   Mail back errors
                    w   Write back errors (mail if user not logged in)
                    e   Mail back errors (when applicable) and give zero exit stat always

                Note that the last mode, "e", is for Berknet
                error  processing  and should not be used in
                normal circumstances.  Note, too, that  mode
                "q",   only  applies  to  errors  recognized
                before sendmail forks for background  deliv-
                ery.

      FallbackMXhost=fallbackhost
                [V] If specified, the fallbackhost acts like










SMM:08-108         Sendmail Installation and Operation Guide


                a very low priority MX on  every  host.   MX
                records  will  be  looked  up for this host,
                unless the  name  is  surrounded  by  square
                brackets.   This  is  intended to be used by
                sites with poor network connectivity.   Mes-
                sages  which are undeliverable due to tempo-
                rary address failures  (e.g.,  DNS  failure)
                also go to the FallbackMXhost.

      FallBackSmartHost=hostname
                If  specified, the FallBackSmartHost will be
                used in a last-ditch effort for  each  host.
                This  is  intended  to be used by sites with
                "fake internal DNS", e.g., a  company  whose
                DNS  accurately  reflects  the  world inside
                that company's domain but not outside.

      FastSplit [no short name] If set to  a  value  greater
                than  zero  (the  default  is  one), it sup-
                presses the MX  lookups  on  addresses  when
                they  are  initially  sorted,  i.e., for the
                first  delivery   attempt.    This   usually
                results  in faster envelope splitting unless
                the MX records are readily  available  in  a
                local DNS cache.  To enforce initial sorting
                based on MX records set FastSplit  to  zero.
                If  the  mail is submitted directly from the
                command line, then the value also limits the
                number   of   processes   to   deliver   the
                envelopes; if  more  envelopes  are  created
                they  are  only  queued up and must be taken
                care of by a queue run.  Since  the  default
                submission method is via SMTP (either from a
                MUA or via the MSP), the value of  FastSplit
                is  seldom  used to limit the number of pro-
                cesses to deliver the envelopes.

      ForkEachJob
                [Y] If set, deliver each  job  that  is  run
                from the queue in a separate process.

      ForwardPath=path
                [J]  Set  the  path for searching for users'
                .forward files.  The  default  is  "$z/.for-
                ward".   Some sites that use the automounter
                may prefer  to  change  this  to  "/var/for-
                ward/$u" to search a file with the same name
                as the user in a system directory.   It  can
                also be set to a sequence of paths separated
                by colons; sendmail stops at the first  file
                it  can  successfully  and safely open.  For
                example, "/var/forward/$u:$z/.forward"  will
                search  first  in  /var/forward/username and










Sendmail Installation and Operation Guide         SMM:08-109


                then in ~username/.forward (but only if  the
                first file does not exist).

      HeloName=name
                [no  short name] Set the name to be used for
                HELO/EHLO (instead of $j).

      HoldExpensive
                [c] If an outgoing mailer is marked as being
                expensive, don't connect immediately.

      HostsFile=path
                [no  short name] The path to the hosts data-
                base, normally "/etc/hosts".  This option is
                only  consulted when sendmail is canonifying
                addresses, and then only when "files" is  in
                the  "hosts"  service switch entry.  In par-
                ticular, this file is never used when  look-
                ing  up  host  addresses;  that is under the
                control of the system gethostbyname(3)  rou-
                tine.

      HostStatusDirectory=path
                [no  short  name]  The  location of the long
                term host  status  information.   When  set,
                information about the status of hosts (e.g.,
                host down or not accepting connections) will
                be  shared  between  all sendmail processes;
                normally,  this  information  is  only  held
                within  a  single  queue  run.   This option
                requires a connection cache of at least 1 to
                function.  If the option begins with a lead-
                ing `/', it is an absolute pathname;  other-
                wise,  it  is  relative  to  the  mail queue
                directory.   A  suggested  value  for  sites
                desiring  persistent  host status is ".host-
                stat" (i.e., a  subdirectory  of  the  queue
                directory).

      IgnoreDots
                [i]  Ignore dots in incoming messages.  This
                is always disabled (that is, dots are always
                accepted) when reading SMTP mail.

      InputMailFilters=name,name,...
                A  comma  separated  list  of  filters which
                determines which filters (see the "X -- Mail
                Filter  (Milter)  Definitions"  section) and
                the invocation sequence  are  contacted  for
                incoming SMTP messages.  If none are set, no
                filters will be contacted.












SMM:08-110         Sendmail Installation and Operation Guide


      LDAPDefaultSpec=spec
                [no short name] Sets a default map  specifi-
                cation for LDAP maps.  The value should only
                contain LDAP specific settings such  as  "-h
                host  -p port -d bindDN".  The settings will
                be used for all LDAP maps unless  the  indi-
                vidual  map  specification  overrides a set-
                ting.  This option should be set before  any
                LDAP maps are defined.

      LogLevel=n
                [L]  Set the log level to n.  Defaults to 9.

      Mxvalue   [no long version] Set the macro x to  value.
                This  is intended only for use from the com-
                mand line.  The -M flag is preferred.

      MailboxDatabase
                [no short  name]  Type  of  lookup  to  find
                information  about local mailboxes, defaults
                to ``pw'' which uses getpwnam.  Other  types
                can  be  introduced  by  adding  them to the
                source code, see libsm/mbdb.c for details.

      UseMSP    [no short name] Use as mail submission  pro-
                gram, i.e., allow group writable queue files
                if the group is the same as that of  a  set-
                group-ID  sendmail  binary.   See  the  file
                sendmail/SECURITY in the  distribution  tar-
                ball.

      MatchGECOS
                [G] Allow fuzzy matching on the GECOS field.
                If this flag is set, and the usual user name
                lookups  fail  (that  is,  there is no alias
                with  this  name  and  a  getpwnam   fails),
                sequentially  search the password file for a
                matching entry in  the  GECOS  field.   This
                also  requires  that MATCHGECOS be turned on
                during compilation.  This option is not rec-
                ommended.

      MaxAliasRecursion=N
                [no  short  name] The maximum depth of alias
                recursion (default: 10).

      MaxDaemonChildren=N
                [no short name] If set, sendmail will refuse
                connections when it has more than N children
                processing incoming mail or automatic  queue
                runs.   This  does  not  limit the number of
                outgoing connections.  If the default Deliv-
                eryMode  (background) is used, then sendmail










Sendmail Installation and Operation Guide         SMM:08-111


                may create an  almost  unlimited  number  of
                children  (depending on the number of trans-
                actions and the relative execution times  of
                mail  receiption and mail delivery).  If the
                limit should be enforced, then  a  Delivery-
                Mode other than background must be used.  If
                not set, there is no limit to the number  of
                children -- that is, the system load average
                controls this.

      MaxHeadersLength=N
                [no short name] The maximum  length  of  the
                sum  of  all  headers.   This can be used to
                prevent a denial  of  service  attack.   The
                default is no limit.

      MaxHopCount=N
                [h]  The  maximum  hop count.  Messages that
                have been processed more than  N  times  are
                assumed  to  be  in a loop and are rejected.
                Defaults to 25.

      MaxMessageSize=N
                [no short name] Specify the maximum  message
                size  to  be  advertised  in  the ESMTP EHLO
                response.  Messages larger than this will be
                rejected.   If  set  to a value greater than
                zero, that value will be listed in the  SIZE
                response,  otherwise  SIZE  is advertised in
                the ESMTP EHLO response without a parameter.

      MaxMimeHeaderLength=N[/M]
                [no  short  name] Sets the maximum length of
                certain MIME header field values to N  char-
                acters.  These MIME header fields are deter-
                mined by being a member of class {checkMIME-
                TextHeaders},  which currently contains only
                the header Content-Description.  For some of
                these  headers  which  take  parameters, the
                maximum length of each parameter is set to M
                if  specified.   If /M is not specified, one
                half of N will be used.  By  default,  these
                values  are 2048 and 1024, respectively.  To
                allow any length, a value of 0 can be speci-
                fied.

      MaxNOOPCommands=N
                Override  the default of MAXNOOPCOMMANDS for
                the number of useless commands, see  Section
                "Measures    against   Denial   of   Service
                Attacks".












SMM:08-112         Sendmail Installation and Operation Guide


      MaxQueueChildren=N
                [no short name] When set,  this  limits  the
                number  of concurrent queue runner processes
                to N.  This helps to control the  amount  of
                system  resources  used  when processing the
                queue.  When there are multiple queue groups
                defined  and  the total number of queue run-
                ners for these  queue  groups  would  exceed
                MaxQueueChildren  then the queue groups will
                not all run concurrently. That is, some por-
                tion  of  the  queue groups will run concur-
                rently such that MaxQueueChildren  will  not
                be   exceeded,  while  the  remaining  queue
                groups will be run  later  (in  round  robin
                order).  See also MaxRunnersPerQueue and the
                section Queue  Group  Declaration.   Notice:
                sendmail  does  not  count  individual queue
                runners, but only sets of processes that act
                on  a workgroup.  Hence the actual number of
                queue runners may be lower  than  the  limit
                imposed  by MaxQueueChildren.  This discrep-
                ancy can be large if some queue runners have
                to  wait  for  a  slow  server  and if short
                intervals are used.

      MaxQueueRunSize=N
                [no short name] The maximum number  of  jobs
                that  will  be  processed  in a single queue
                run.  If not set, there is no limit  on  the
                size.   If  you  have very large queues or a
                very short queue run interval this could  be
                unstable.   However,  since the first N jobs
                in queue directory  order  are  run  (rather
                than  the  N  highest  priority  jobs)  this
                should be set as high as possible  to  avoid
                "losing"  jobs  that  happen to fall late in
                the queue directory.  Note: this option also
                restricts  the  number of entries printed by
                mailq.  That is, if MaxQueueRunSize  is  set
                to  a  value N larger than zero, then only N
                entries are printed per queue group.

      MaxRecipientsPerMessage=N
                [no short name] The maximum number of recip-
                ients  that  will be accepted per message in
                an SMTP transaction.  Note: setting this too
                low  can  interfere  with  sending mail from
                MUAs that use SMTP for  initial  submission.
                If  not set, there is no limit on the number
                of recipients per envelope.

      MaxRunnersPerQueue=N
                [no  short  name]  This  sets  the   default










Sendmail Installation and Operation Guide         SMM:08-113


                maximum  number  of  queue runners for queue
                groups.  Up to N queue runners will work  in
                parallel  on a queue group's messages.  This
                is useful where the processing of a  message
                in  the  queue might delay the processing of
                subsequent messages. Such a delay may be the
                result of non-erroneous situations such as a
                low bandwidth connection.  May be overridden
                on  a  per  queue group basis by setting the
                Runners option; see the section Queue  Group
                Declaration.  The default is 1 when not set.

      MeToo     [m] Send to me too, even if I am in an alias
                expansion.   This  option  is deprecated and
                will be removed from a future version.

      Milter    [no short  name]  This  option  has  several
                sub(sub)options.   The  names  of the subop-
                tions are separated by dots.  At  the  first
                level the following options are available:

                    LogLevel   Log level for input mail filter actions, defaults to LogLevel.
                    macros     Specifies list of macro to transmit to filters.
                               See list below.

                The ``macros'' option has the following sub-
                options which specify the list of  macro  to
                transmit  to  milters  after a certain event
                occurred.

                    connect   After session connection start
                    helo      After EHLO/HELO command
                    envfrom   After MAIL From command
                    envrcpt   After RCPT To command
                    data      After DATA command.
                    eoh       After DATA command and header
                    eom       After DATA command and terminating ``.''

                By default the lists of  macros  are  empty.
                Example:

                    O Milter.LogLevel=12
                    O Milter.macros.connect=j, _, {daemon_name}


      MinFreeBlocks=N
                [b]  Insist on at least N blocks free on the
                filesystem that holds the queue files before
                accepting  email  via  SMTP.   If  there  is
                insufficient  space  sendmail  gives  a  452
                response  to the MAIL command.  This invites
                the sender to try again later.











SMM:08-114         Sendmail Installation and Operation Guide


      MinQueueAge=age
                [no short name]  Don't  process  any  queued
                jobs  that  have been in the queue less than
                the  indicated  time  interval.    This   is
                intended  to allow you to get responsiveness
                by processing the  queue  fairly  frequently
                without thrashing your system by trying jobs
                too often.  The default units are minutes.

      MustQuoteChars=s
                [no short name] Sets the list of  characters
                that  must  be quoted if used in a full name
                that is in the phrase  part  of  a  ``phrase
                <address>''  syntax.  The default is ``'.''.
                The  characters  ``@,;:\()[]''  are   always
                added to this list.

      NiceQueueRun
                [no  short  name] The priority of queue run-
                ners (nice(3)).  This value must be  greater
                or equal zero.

      NoRecipientAction
                [no  short name] The action to take when you
                receive a message that has no valid  recipi-
                ent  headers (To:, Cc:, Bcc:, or Apparently-
                To: -- the last included for  back  compati-
                bility  with old sendmails).  It can be None
                to pass the  message  on  unmodified,  which
                violates  the  protocol, Add-To to add a To:
                header with any recipients it  can  find  in
                the envelope (which might expose Bcc: recip-
                ients), Add-Apparently-To to add  an  Appar-
                ently-To: header (this is only for back-com-
                patibility and  is  officially  deprecated),
                Add-To-Undisclosed  to  add  a  header  "To:
                undisclosed-recipients:;" to make the header
                legal  without  disclosing anything, or Add-
                Bcc to add an empty Bcc: header.

      OldStyleHeaders
                [o] Assume that the headers may  be  in  old
                format,  i.e.,  spaces  delimit names.  This
                actually turns on an adaptive algorithm:  if
                any  recipient  address  contains  a  comma,
                parenthesis, or angle bracket,  it  will  be
                assumed  that commas already exist.  If this
                flag is not on, only commas  delimit  names.
                Headers   are   always  output  with  commas
                between the names.  Defaults to off.

      OperatorChars=charlist
                [$o macro] The list of characters  that  are










Sendmail Installation and Operation Guide         SMM:08-115


                considered to be "operators", that is, char-
                acters that delimit  tokens.   All  operator
                characters   are   tokens   by   themselves;
                sequences  of  non-operator  characters  are
                also  tokens.   White space characters sepa-
                rate tokens but are not tokens themselves --
                for example, "AAA.BBB" has three tokens, but
                "AAA BBB" has two.  If  not  set,  Operator-
                Chars defaults to ".:@[]"; additionally, the
                characters "()<>,;"  are  always  operators.
                Note  that  OperatorChars must be set in the
                configuration file before any rulesets.

      PidFile=filename
                [no short name] Filename of  the  pid  file.
                (default  is  _PATH_SENDMAILPID).  The file-
                name is macro-expanded before it is  opened,
                and unlinked when sendmail exits.

      PostmasterCopy=postmaster
                [P] If set, copies of error messages will be
                sent to  the  named  postmaster.   Only  the
                header   of  the  failed  message  is  sent.
                Errors resulting from messages with a  nega-
                tive  precedence  will  not  be sent.  Since
                most errors are user problems, this is prob-
                ably  not  a  good  idea on large sites, and
                arguably contains all sorts of privacy  vio-
                lations,  but  it  seems  to be popular with
                certain  operating  systems  vendors.    The
                address  is  macro  expanded  at the time of
                delivery.  Defaults to no postmaster copies.

      PrivacyOptions=opt,opt,...
                [p] Set the privacy options.  ``Privacy'' is
                really a misnomer; many of these are just  a
                way  of  insisting  on stricter adherence to
                the  SMTP  protocol.   The  options  can  be
                selected from:
























SMM:08-116         Sendmail Installation and Operation Guide


                    public              Allow open access
                    needmailhelo        Insist on HELO or EHLO command before MAIL
                    needexpnhelo        Insist on HELO or EHLO command before EXPN
                    noexpn              Disallow EXPN entirely, implies noverb.
                    needvrfyhelo        Insist on HELO or EHLO command before VRFY
                    novrfy              Disallow VRFY entirely
                    noetrn              Disallow ETRN entirely
                    noverb              Disallow VERB entirely
                    restrictmailq       Restrict mailq command
                    restrictqrun        Restrict -q command line flag
                    restrictexpand      Restrict -bv and -v command line flags
                    noreceipts          Don't return success DSNs[20]
                    nobodyreturn        Don't return the body of a message with DSNs
                    goaway              Disallow essentially all SMTP status queries
                    authwarnings        Put X-Authentication-Warning: headers in messages
                                        and log warnings
                    noactualrecipient   Don't put X-Actual-Recipient lines in DSNs
                                        which reveal the actual account that addresses map to.

                The  "goaway"  pseudo-flag  sets  all  flags
                except     "noreceipts",    "restrictmailq",
                "restrictqrun", "restrictexpand",  "noetrn",
                and "nobodyreturn".  If mailq is restricted,
                only people in the same group as  the  queue
                directory  can  print  the  queue.  If queue
                runs are restricted, only root and the owner
                of  the  queue  directory can run the queue.
                The "restrictexpand"  pseudo-flag  instructs
                sendmail  to  drop  privileges  when the -bv
                option is given by  users  who  are  neither
                root  nor  the  TrustedUser  so users cannot
                read private aliases, forwards, or :include:
                files.  It will add the "NonRootSafeAddr" to
                the "DontBlameSendmail"  option  to  prevent
                misleading unsafe address warnings.  It also
                overrides  the  -v  (verbose)  command  line
                option   to   prevent  information  leakage.
                Authentication Warnings add  warnings  about
                various   conditions   that   may   indicate
                attempts to spoof the mail system,  such  as
                using a non-standard queue directory.

      ProcessTitlePrefix=string
                [no  short  name]  Prefix  the process title
                shown on 'ps'  listings  with  string.   The
                string will be macro processed.


____________________
   [20]N.B.:  the  noreceipts flag turns off support for RFC
1891 (Delivery Status Notification).












Sendmail Installation and Operation Guide         SMM:08-117


      QueueDirectory=dir
                [Q]  The  QueueDirectory  option  serves two
                purposes.  First, it specifies the directory
                or  set  of  directories  that  comprise the
                default queue group.  Second,  it  specifies
                the directory D which is the ancestor of all
                queue directories, and which  sendmail  uses
                as  its  current  working  directory.   When
                sendmail dumps  core,  it  leaves  its  core
                files  in  D.   There are two cases.  If dir
                ends     with     an      asterisk      (eg,
                /var/spool/mqueue/qd*),   then  all  of  the
                directories or symbolic links to directories
                beginning  with  `qd'  in  /var/spool/mqueue
                will be used as  queue  directories  of  the
                default  queue  group, and /var/spool/mqueue
                will be used as  the  working  directory  D.
                Otherwise,  dir  must name a directory (usu-
                ally /var/spool/mqueue): the  default  queue
                group consists of the single queue directory
                dir, and the working directory D is  set  to
                dir.   To  define additional groups of queue
                directories, use the configuration file  `Q'
                command.   Do not change the queue directory
                structure while sendmail is running.

      QueueFactor=factor
                [q] Use factor as the multiplier in the  map
                function  to  decide  when  to just queue up
                jobs rather than run them.   This  value  is
                divided  by  the difference between the cur-
                rent load average and the load average limit
                (QueueLA  option)  to  determine the maximum
                message  priority   that   will   be   sent.
                Defaults to 600000.

      QueueLA=LA
                [x]  When the system load average exceeds LA
                and the QueueFactor (q)  option  divided  by
                the  difference  in the current load average
                and the QueueLA option plus one is less than
                the priority of the message, just queue mes-
                sages  (i.e.,  don't  try  to  send   them).
                Defaults  to  8  multiplied by the number of
                processors online on the system (if that can
                be determined).

      QueueFileMode=mode
                [no  short  name]  Default  permissions  for
                queue files (octal).  If not  set,  sendmail
                uses  0600 unless its real and effective uid
                are different in which case it uses 0644.











SMM:08-118         Sendmail Installation and Operation Guide


      QueueSortOrder=algorithm
                [no short name] Sets the algorithm used  for
                sorting the queue.  Only the first character
                of the value  is  used.   Legal  values  are
                "host"  (to  order  by the name of the first
                host name of the  first  recipient),  "file-
                name"  (to  order  by  the name of the queue
                file name), "time" (to order by the  submis-
                sion/creation time), "random" (to order ran-
                domly), "modification" (to order by the mod-
                ification time of the qf file (older entries
                first)), "none" (to not order), and  "prior-
                ity"  (to  order by message priority).  Host
                ordering makes better use of the  connection
                cache,  but may tend to process low priority
                messages that go to a single host over  high
                priority  messages that go to several hosts;
                it probably shouldn't be used on  slow  net-
                work  links.  Filename and modification time
                ordering saves the overhead of  reading  all
                of  the  queued  items  before  starting the
                queue  run.   Creation   (submission)   time
                ordering  is almost always a bad idea, since
                it allows large, bulk mail to go out  before
                smaller,  personal mail, but may have appli-
                cability on some hosts with very  fast  con-
                nections.  Random is useful if several queue
                runners are started by  hand  which  try  to
                drain  the  same  queue  since odds are they
                will be working on different  parts  of  the
                queue  at  the same time.  Priority ordering
                is the default.

      QueueTimeout=timeout
                [T]  A  synonym  for  "Timeout.queuereturn".
                Use  that form instead of the "QueueTimeout"
                form.

      RandFile  [no short name] Name of file containing ran-
                dom  data  or the name of the UNIX socket if
                EGD is used.  A (required) prefix "egd:"  or
                "file:"   specifies   the   type.   STARTTLS
                requires this filename if the  compile  flag
                HASURANDOMDEV   is   not   set   (see  send-
                mail/README).

      ResolverOptions=options
                [I] Set resolver options.  Values can be set
                using  +flag  and  cleared  using -flag; the
                flags can  be  "debug",  "aaonly",  "usevc",
                "primary",  "igntc",  "recurse", "defnames",
                "stayopen", "use_inet6", or  "dnsrch".   The
                string  "HasWildcardMX"  (without  a + or -)










Sendmail Installation and Operation Guide         SMM:08-119


                can  be  specified  to  turn  off   matching
                against MX records when doing name canonifi-
                cations.  The string  "WorkAroundBrokenAAAA"
                (without  a + or -) can be specified to work
                around some broken nameservers which  return
                SERVFAIL  (a  temporary  failure)  on T_AAAA
                (IPv6) lookups.  Notice: it might be  neces-
                sary  to apply the same (or similar) options
                to submit.cf too.

      RequiresDirfsync
                [no short name] This option can be  used  to
                override     the     compile    time    flag
                REQUIRES_DIR_FSYNC at runtime by setting  it
                to  false.   If the compile time flag is not
                set, the option is ignored.  The flag  turns
                on  support for file systems that require to
                call fsync() for a directory  if  the  meta-
                data in it has been changed.  This should be
                turned on at least  for  older  versions  of
                ReiserFS;  it  is  enabled  by  default  for
                Linux.  According to some  information  this
                flag is not needed anymore for kernel 2.4.16
                and newer.

      RrtImpliesDsn
                [R]  If  this  option  is  set,  a  "Return-
                Receipt-To:"  header causes the request of a
                DSN, which is sent to the envelope sender as
                required  by  RFC  1891,  not to the address
                given in the header.

      RunAsUser=user
                [no short name] The user parameter may be  a
                user  name  (looked  up in /etc/passwd) or a
                numeric  user  id;  either  form  can   have
                ":group"   attached   (where  group  can  be
                numeric or symbolic).  If set to a  non-zero
                (non-root)  value,  sendmail  will change to
                this  user  id  shortly  after  startup[21].
                This  avoids  a  certain  class  of security
                problems.   However,  this  means  that  all
                ".forward"  and  ":include:"  files  must be
                readable by the indicated user and all files
                to be written must be writable by user Also,
                all file  and  program  deliveries  will  be
                marked     unsafe    unless    the    option
____________________
   [21]When running as a daemon, it changes to this user af-
ter  accepting a connection but before reading any SMTP com-
mands.












SMM:08-120         Sendmail Installation and Operation Guide


                DontBlameSendmail=NonRootSafeAddr is set, in
                which  case  the  delivery  will  be done as
                user.  It  is  also  incompatible  with  the
                SafeFileEnvironment option.  In other words,
                it may not actually add much to security  on
                an  average  system, and may in fact detract
                from security (because  other  file  permis-
                sions must be loosened).  However, it should
                be useful  on  firewalls  and  other  places
                where  users  don't  have  accounts  and the
                aliases file is well constrained.

      RecipientFactor=fact
                [y] The indicated factor  is  added  to  the
                priority  (thus lowering the priority of the
                job) for each recipient,  i.e.,  this  value
                penalizes jobs with large numbers of recipi-
                ents.  Defaults to 30000.

      RefuseLA=LA
                [X] When the system load average exceeds LA,
                refuse  incoming SMTP connections.  Defaults
                to 12 multiplied by the number of processors
                online  on the system (if that can be deter-
                mined).

      RejectLogInterval=timeout
                [no short name] Log interval  when  refusing
                connections for this long (default: 3h).

      RetryFactor=fact
                [Z]  The  factor  is  added  to the priority
                every time a job is processed.   Thus,  each
                time  a  job is processed, its priority will
                be decreased by  the  indicated  value.   In
                most  environments  this should be positive,
                since hosts that are down are all too  often
                down for a long time.  Defaults to 90000.

      SafeFileEnvironment=dir
                [no short name] If this option is set, send-
                mail will do a chroot(2) call into the indi-
                cated   directory   before  doing  any  file
                writes.  If the file name specified  by  the
                user begins with dir, that partial path name
                will be stripped off before writing, so (for
                example) if the SafeFileEnvironment variable
                is  set   to   "/safe"   then   aliases   of
                "/safe/logs/file"  and "/logs/file" actually
                indicate the same  file.   Additionally,  if
                this  option  is  set,  sendmail  refuses to
                deliver to symbolic links.











Sendmail Installation and Operation Guide         SMM:08-121


      SaveFromLine
                [f] Save  UNIX-style  "From"  lines  at  the
                front of headers.  Normally they are assumed
                redundant and discarded.

      SendMimeErrors
                [j] If set, send error messages in MIME for-
                mat (see RFC 2045 and RFC 1344 for details).
                If disabled, sendmail will  not  return  the
                DSN  keyword in response to an EHLO and will
                not do Delivery Status Notification process-
                ing as described in RFC 1891.

      ServerCertFile
                [no short name] File containing the certifi-
                cate of the server, i.e.,  this  certificate
                is  used  when sendmail acts as server (used
                for STARTTLS).

      ServerKeyFile
                [no short name] File containing the  private
                key  belonging  to  the  server  certificate
                (used for STARTTLS).

      ServiceSwitchFile=filename
                [no short name] If your host operating  sys-
                tem  has a service switch abstraction (e.g.,
                /etc/nsswitch.conf     on     Solaris     or
                /etc/svc.conf  on Ultrix and DEC OSF/1) that
                service will be consulted and this option is
                ignored.   Otherwise,  this is the name of a
                file that provides the list of methods  used
                to  implement particular services.  The syn-
                tax is a series of lines, each of which is a
                sequence  of  words.   The first word is the
                service name, and following words  are  ser-
                vice types.  The services that sendmail con-
                sults directly are  "aliases"  and  "hosts."
                Service  types  can  be  "dns", "nis", "nis-
                plus", or "files" (with the caveat that  the
                appropriate  support  must  be  compiled  in
                before the service can be  referenced).   If
                ServiceSwitchFile   is   not  specified,  it
                defaults  to  /etc/mail/service.switch.   If
                that file does not exist, the default switch
                is:

                    aliases             files
                    hosts               dns nis files

                The   default   file   is    "/etc/mail/ser-
                vice.switch".











SMM:08-122         Sendmail Installation and Operation Guide


      SevenBitInput
                [7]  Strip  input to seven bits for compati-
                bility with old systems.  This shouldn't  be
                necessary.

      SharedMemoryKey
                [no short name] Key to use for shared memory
                segment; if not set (or  0),  shared  memory
                will not be used.  If set to -1 sendmail can
                select  a  key  itself  provided  that  also
                SharedMemoryKeyFile  is  set.  Requires sup-
                port for shared memory to be  compiled  into
                sendmail.   If  this option is set, sendmail
                can  share  some  data   between   different
                instances.    For  example,  the  number  of
                entries in a queue directory or  the  avail-
                able  space  in  a file system.  This allows
                for more efficient program execution,  since
                only  one  process  needs to update the data
                instead of each individual process gathering
                the data each time it is required.

      SharedMemoryKeyFile
                [no short name] If SharedMemoryKey is set to
                -1 then the  automatically  selected  shared
                memory  key  will be stored in the specified
                file.

      SingleLineFromHeader
                [no short name] If  set,  From:  lines  that
                have  embedded  newlines  are unwrapped onto
                one line.  This is to get around a botch  in
                Lotus  Notes  that  apparently cannot under-
                stand legally wrapped RFC 822 headers.

      SingleThreadDelivery
                [no short name] If  set,  a  client  machine
                will  never try to open two SMTP connections
                to a single server machine at the same time,
                even  in  different  processes.  That is, if
                another sendmail is already talking to  some
                host  a  new  sendmail will not open another
                connection.   This  property  is  of   mixed
                value; although this reduces the load on the
                other machine,  it  can  cause  mail  to  be
                delayed  (for  example,  if  one sendmail is
                delivering a huge message,  other  sendmails
                won't  be able to send even small messages).
                Also, it requires  another  file  descriptor
                (for  the  lock file) per connection, so you
                may have to reduce  the  ConnectionCacheSize
                option  to  avoid running out of per-process
                file     descriptors.      Requires      the










Sendmail Installation and Operation Guide         SMM:08-123


                HostStatusDirectory option.

      SmtpGreetingMessage=message
                [$e macro] The message printed when the SMTP
                server starts up.  Defaults to "$j  Sendmail
                $v ready at $b".

      SoftBounce
                If set, issue temporary errors (4xy) instead
                of permanent errors (5xy).  This can be use-
                ful during testing of a new configuration to
                avoid erroneous bouncing of mails.

      StatusFile=file
                [S] Log  summary  statistics  in  the  named
                file.   If  no file name is specified, "sta-
                tistics" is used.  If not  set,  no  summary
                statistics  are  saved.   This file does not
                grow in size.  It can be printed  using  the
                mailstats(8) program.

      SuperSafe [s]  This  option can be set to True, False,
                Interactive, or PostMilter.  If set to True,
                sendmail  will  be  super-safe  when running
                things, i.e., always instantiate  the  queue
                file, even if you are going to attempt imme-
                diate delivery.  Sendmail  always  instanti-
                ates the queue file before returning control
                to the client under any circumstances.  This
                should  really  always  be set to True.  The
                Interactive value  has  been  introduced  in
                8.12 and can be used together with Delivery-
                Mode=i.  It skips some synchronization calls
                which  are  effectively  doubled in the code
                execution path for this  mode.   If  set  to
                PostMilter,  sendmail  defers  synchronizing
                the queue file until any milters  have  sig-
                naled acceptance of the message.  PostMilter
                is useful only when sendmail is  running  as
                an  SMTP  server; in all other situations it
                acts the same as True.

      TLSSrvOptions
                [no short name] List  of  options  for  SMTP
                STARTTLS for the server consisting of single
                characters with intervening white  space  or
                commas.  The flag ``V'' disables client ver-
                ification, and hence it is not  possible  to
                use a client certificate for relaying.  Cur-
                rently there are no other flags available.

      TempFileMode=mode
                [F] The  file  mode  for  transcript  files,










SMM:08-124         Sendmail Installation and Operation Guide


                files  to  which sendmail delivers directly,
                files in the HostStatusDirectory,  and  Sta-
                tusFile.   It  is  interpreted  in  octal by
                default.  Defaults to 0600.

      Timeout.type=timeout
                [r; subsumes old T option as well] Set time-
                out  values.  For more information, see sec-
                tion 4.1.

      TimeZoneSpec=tzinfo
                [t] Set the local time zone info  to  tzinfo
                --  for  example,  "PST8PDT".   Actually, if
                this is not set, the TZ environment variable
                is  cleared (so the system default is used);
                if set but null, the user's TZ  variable  is
                used,  and  if set and non-null the TZ vari-
                able is set to this value.

      TrustedUser=user
                [no short name] The user parameter may be  a
                user  name  (looked  up in /etc/passwd) or a
                numeric user id.  Trusted user for file own-
                ership  and  starting  the  daemon.  If set,
                generated alias databases  and  the  control
                socket (if configured) will automatically be
                owned by this user.

      TryNullMXList
                [w] If this system is the "best"  (that  is,
                lowest  preference) MX for a given host, its
                configuration rules should  normally  detect
                this situation and treat that condition spe-
                cially by forwarding  the  mail  to  a  UUCP
                feed,  treating  it  as  local, or whatever.
                However, in some  cases  (such  as  Internet
                firewalls)  you  may  want to try to connect
                directly to that host as though it had no MX
                records  at all.  Setting this option causes
                sendmail to try this.  The downside is  that
                errors  in  your configuration are likely to
                be diagnosed as "host unknown"  or  "message
                timed  out"  instead of something more mean-
                ingful.  This option is disrecommended.

      UnixFromLine=fromline
                [$l macro]  Defines  the  format  used  when
                sendmail  must  add  a UNIX-style From_ line
                (that     is,     a      line      beginning
                "From<space>user").   Defaults  to  "From $g
                $d".  Don't change this unless  your  system
                uses  a  different UNIX mailbox format (very
                unlikely).










Sendmail Installation and Operation Guide         SMM:08-125


      UnsafeGroupWrites
                [no short name] If set (default),  :include:
                and  .forward  files that are group writable
                are considered "unsafe", that is, they  can-
                not  reference programs or write directly to
                files.  World writable :include:  and  .for-
                ward  files  are  always  unsafe.  Note: use
                DontBlameSendmail instead;  this  option  is
                deprecated.

      UseErrorsTo
                [l] If there is an "Errors-To:" header, send
                error  messages  to  the  addresses   listed
                there.   They  normally  go  to the envelope
                sender.  Use of this option causes  sendmail
                to violate RFC 1123.  This option is disrec-
                ommended and deprecated.

      UserDatabaseSpec=udbspec
                [U] The user database specification.

      Verbose   [v] Run in verbose mode.  If  this  is  set,
                sendmail  adjusts options HoldExpensive (old
                c) and DeliveryMode (old d) so that all mail
                is  delivered  completely in a single job so
                that  you  can  see  the   entire   delivery
                process.  Option Verbose should never be set
                in the configuration file;  it  is  intended
                for  command  line  use only.  Note that the
                use of option Verbose can cause  authentica-
                tion information to leak, if you use a send-
                mail client to authenticate to a server.  If
                the authentication mechanism uses plain text
                passwords (as with LOGIN or PLAIN), then the
                password  could  be  compromised.   To avoid
                this, do not  install  sendmail  set-user-ID
                root, and disable the VERB SMTP command with
                a suitable PrivacyOptions setting.

      XscriptFileBufferSize=threshold
                [no short name] Set the threshold, in bytes,
                before  a memory-based queue transcript file
                becomes disk-based.   The  default  is  4096
                bytes.

      All options can be specified on the command line using
      the -O or -o flag, but most  will  cause  sendmail  to
      relinquish  its  set-user-ID permissions.  The options
      that will not cause this are SevenBitInput [7], Eight-
      BitMode  [8],  MinFreeBlocks  [b],  CheckpointInterval
      [C], DeliveryMode [d], ErrorMode [e], IgnoreDots  [i],
      SendMimeErrors [j], LogLevel [L], MeToo [m], OldStyle-
      Headers  [o],  PrivacyOptions  [p],   SuperSafe   [s],










SMM:08-126         Sendmail Installation and Operation Guide


      Verbose  [v],  QueueSortOrder,  MinQueueAge,  Default-
      CharSet, Dial Delay, NoRecipientAction, ColonOkInAddr,
      MaxQueueRunSize,  SingleLineFromHeader,  and  AllowBo-
      gusHELO.  Actually, PrivacyOptions [p]  given  on  the
      command  line  are added to those already specified in
      the sendmail.cf  file,  i.e.,  they  can't  be  reset.
      Also, M (define macro) when defining the r or s macros
      is also considered "safe".

   5.7.  P -- Precedence Definitions

           Values for the "Precedence:" field may be defined
      using  the  P  control line.  The syntax of this field
      is:

          Pname=num

      When the name is found in a "Precedence:"  field,  the
      message  class  is  set  to  num.  Higher numbers mean
      higher precedence.  Numbers less than  zero  have  the
      special  property  that if an error occurs during pro-
      cessing the body of the message will not be  returned;
      this  is  expected  to be used for "bulk" mail such as
      through mailing  lists.   The  default  precedence  is
      zero.  For example, our list of precedences is:

          Pfirst-class=0
          Pspecial-delivery=100
          Plist=-30
          Pbulk=-60
          Pjunk=-100

      People  writing  mailing list exploders are encouraged
      to use "Precedence: list".  Older versions of sendmail
      (which discarded all error returns for negative prece-
      dences)  didn't  recognize  this  name,  giving  it  a
      default  precedence  of  zero.  This allows list main-
      tainers to see error returns on both old and new  ver-
      sions of sendmail.

   5.8.  V -- Configuration Version Level

           To  provide  compatibility with old configuration
      files, the V line has been added to define  some  very
      basic  semantics of the configuration file.  These are
      not intended to be long term  supports;  rather,  they
      describe compatibility features which will probably be
      removed in future releases.

           N.B.: these version levels  have  nothing  to  do
      with the version number on the files.  For example, as
      of this writing version 10 config files (specifically,
      8.10) used version level 9 configurations.










Sendmail Installation and Operation Guide         SMM:08-127


           "Old"  configuration files are defined as version
      level one.  Version level two files make the following
      changes:

       (1)   Host  name canonification ($[ ... $]) appends a
             dot if the name is recognized; this  gives  the
             config  file  a  way of finding out if anything
             matched.  (Actually, this just initializes  the
             "host"  map  with  the  "-a."   flag -- you can
             reset it to anything you  prefer  by  declaring
             the map explicitly.)

       (2)   Default   host  name  extension  is  consistent
             throughout processing; version level  one  con-
             figurations  turned  off domain extension (that
             is, adding the local domain name)  during  cer-
             tain  points  in processing.  Version level two
             configurations are expected to include a trail-
             ing  dot  to  indicate that the name is already
             canonical.

       (3)   Local names that are  not  aliases  are  passed
             through  a new distinguished ruleset five; this
             can be used to  append  a  local  relay.   This
             behavior  can  be  prevented  by  resolving the
             local name with an initial `@'.  That is, some-
             thing  that  resolves  to  a local mailer and a
             user name of "vikki"  will  be  passed  through
             ruleset  five, but a user name of "@vikki" will
             have the  `@'  stripped,  will  not  be  passed
             through  ruleset  five,  but  will otherwise be
             treated the same as  the  prior  example.   The
             expectation  is  that  this  might  be  used to
             implement a policy where mail sent  to  "vikki"
             was  handled by a central hub, but mail sent to
             "vikki@localhost" was delivered directly.

           Version level three files allow # initiated  com-
      ments  on all lines.  Exceptions are backslash escaped
      # marks and the $# syntax.

           Version level four configurations are  completely
      equivalent to level three for historical reasons.

           Version level five configuration files change the
      default definition of $w to be just the  first  compo-
      nent of the hostname.

           Version level six configuration files change many
      of the local processing options (such as aliasing  and
      matching  the beginning of the address for `|' charac-
      ters) to be mailer  flags;  this  allows  fine-grained
      control  over the special local processing.  Level six










SMM:08-128         Sendmail Installation and Operation Guide


      configuration files may also use  long  option  names.
      The  ColonOkInAddr  option  (to  allow  colons  in the
      local-part of addresses) defaults on  for  lower  num-
      bered  configuration  files;  the  configuration  file
      requires some additional intelligence to properly han-
      dle the RFC 822 group construct.

           Version  level seven configuration files used new
      option names to replace old macros  ($e  became  Smtp-
      GreetingMessage, $l became UnixFromLine, and $o became
      OperatorChars.  Also, prior to version seven, the  F=q
      flag  (use  250  instead  of 252 return value for SMTP
      VRFY commands) was assumed.

           Version level eight configuration files allow  $#
      on the left hand side of ruleset lines.

           Version  level  nine  configuration  files  allow
      parentheses in rulesets, i.e. they are not treated  as
      comments and hence removed.

           Version level ten configuration files allow queue
      group definitions.

           The V line may have an optional /vendor to  indi-
      cate  that  this configuration file uses modifications
      specific  to  a  particular  vendor[22].   You may use
      "/Berkeley" to emphasize that this configuration  file
      uses the Berkeley dialect of sendmail.

   5.9.  K -- Key File Declaration

           Special maps can be defined using the line:

          Kmapname mapclass arguments

      The  mapname is the handle by which this map is refer-
      enced in the rewriting rules.   The  mapclass  is  the
      name  of a type of map; these are compiled in to send-
      mail.  The arguments are interpreted depending on  the
      class;  typically,  there  would  be a single argument
      naming the file containing the map.

           Maps are referenced using the syntax:

          $( map key $@ arguments $: default $)
____________________
   [22]And of course, vendors are encouraged  to  add  them-
selves to the list of recognized vendors by editing the rou-
tine setvendor in  conf.c.   Please  send  e-mail  to  send-
mail@Sendmail.ORG to register your vendor dialect.












Sendmail Installation and Operation Guide         SMM:08-129


      where either or both of the arguments or default  por-
      tion may be omitted.  The $@ arguments may appear more
      than once.  The indicated key and arguments are passed
      to  the appropriate mapping function.  If it returns a
      value, it replaces the input.  If it does not return a
      value  and  the  default  is  specified,  the  default
      replaces  the  input.    Otherwise,   the   input   is
      unchanged.

           The arguments are passed to the map for arbitrary
      use.  Most map classes can interpolate these arguments
      into  their values using the syntax "%n" (where n is a
      digit) to indicate the corresponding argument.   Argu-
      ment  "%0"  indicates  the database key.  For example,
      the rule

          R$- ! $+       $: $(uucp $1 $@ $2 $: $2 @ $1 . UUCP $)

      Looks up the UUCP name in a (user defined)  UUCP  map;
      if not found it turns it into ".UUCP" form.  The data-
      base might contain records like:

          decvax         %1@%0.DEC.COM
          research       %1@%0.ATT.COM

      Note that default clauses never do this mapping.

           The built-in map with both name and class  "host"
      is  the  host name canonicalization lookup.  Thus, the
      syntax:

          $(host hostname$)

      is equivalent to:

          $[hostname$]


           There are many defined classes.

      dbm       Database lookups using the ndbm(3)  library.
                Sendmail must be compiled with NDBM defined.

      btree     Database lookups using the  btree  interface
                to  the  Berkeley DB library.  Sendmail must
                be compiled with NEWDB defined.

      hash      Database lookups using the hash interface to
                the  Berkeley  DB library.  Sendmail must be
                compiled with NEWDB defined.

      nis       NIS lookups.  Sendmail must be compiled with
                NIS defined.










SMM:08-130         Sendmail Installation and Operation Guide


      nisplus   NIS+  lookups.   Sendmail  must  be compiled
                with NISPLUS defined.  The argument  is  the
                name  of  the  table to use for lookups, and
                the -k and -v flags may be used to  set  the
                key and value columns respectively.

      hesiod    Hesiod  lookups.   Sendmail must be compiled
                with HESIOD defined.

      ldap      LDAP X500 directory lookups.  Sendmail  must
                be  compiled  with LDAPMAP defined.  The map
                supports most of the standard arguments  and
                most  of  the  command line arguments of the
                ldapsearch program.  Note that, by  default,
                if  a  single query matches multiple values,
                only the first value will be returned unless
                the  -z  (value  separator) map flag is set.
                Also, the -1 map flag will treat a  multiple
                value return as if there were no matches.

      netinfo   NeXT NetInfo lookups.  Sendmail must be com-
                piled with NETINFO defined.

      text      Text file lookups.  The format of  the  text
                file  is  defined  by the -k (key field num-
                ber), -v (value field number), and -z (field
                delimiter) flags.

      ph        PH  query map.  Contributed and supported by
                Mark Roth, roth@uiuc.edu.  For more informa-
                tion,  consult  the  web  site  "http://www-
                dev.cites.uiuc.edu/sendmail/".

      nsd       nsd map for IRIX 6.5 and later.  Contributed
                and   supported   by   Bob   Mende  of  SGI,
                mende@sgi.com.

      stab      Internal symbol table lookups.  Used  inter-
                nally for aliasing.

      implicit  Really  should  be called "alias" -- this is
                used to get the default  lookups  for  alias
                files,  and  is  the  default if no class is
                specified for alias files.

      user      Looks up users using  getpwnam(3).   The  -v
                flag  can be used to specify the name of the
                field to return (although this  is  normally
                used only to check the existence of a user).

      host      Canonifies host domain names.  Given a  host
                name  it  calls  the name server to find the
                canonical name for that host.










Sendmail Installation and Operation Guide         SMM:08-131


      bestmx    Returns the best MX record for a  host  name
                given  as  the  key.  The current machine is
                always preferred -- that is, if the  current
                machine is one of the hosts listed as a low-
                est-preference MX record, then  it  will  be
                guaranteed to be returned.  This can be used
                to find out if this machine  is  the  target
                for  an  MX record, and mail can be accepted
                on that basis.  If the  -z  flag  is  given,
                then all MX names are returned, separated by
                the given delimiter.

      dns       This map requires the option -R  to  specify
                the  DNS resource record type to lookup. The
                following  types  are  supported:  A,  AAAA,
                AFSDB,  CNAME, MX, NS, PTR, SRV, and TXT.  A
                map lookup  will  return  only  one  record.
                Hence  for some types, e.g., MX records, the
                return value might be a  random  element  of
                the  list  due  to  randomizing  in  the DNS
                resolver.

      sequence  The arguments on the `K' line are a list  of
                maps;  the  resulting map searches the argu-
                ment maps in order until it  finds  a  match
                for  the indicated key.  For example, if the
                key definition is:

                    Kmap1 ...
                    Kmap2 ...
                    Kseqmap sequence map1 map2

                then a lookup against "seqmap" first does  a
                lookup  in  map1.   If  that  is  found,  it
                returns immediately.   Otherwise,  the  same
                key is used for map2.

      syslog    the  key  is  logged  via  syslogd(8).   The
                lookup returns the empty string.

      switch    Much like the "sequence" map except that the
                order  of  maps is determined by the service
                switch.  The argument is  the  name  of  the
                service to be looked up; the values from the
                service switch are appended to the map  name
                to  create new map names.  For example, con-
                sider the key definition:

                    Kali switch aliases

                together with the service switch entry:

                    aliases        nis files










SMM:08-132         Sendmail Installation and Operation Guide


                This causes a query against the map "ali" to
                search  maps named "ali.nis" and "ali.files"
                in that order.

      dequote   Strip double quotes (")  from  a  name.   It
                does  not  strip  backslashes,  and will not
                strip quotes if the resulting  string  would
                contain  unscannable  syntax (that is, basic
                errors like unbalanced angle brackets;  more
                sophisticated  errors  such as unknown hosts
                are not checked).  The  intent  is  for  use
                when trying to accept mail from systems such
                as DECnet that routinely  quote  odd  syntax
                such as

                    "49ers::ubell"

                A typical usage is probably something like:

                    Kdequote dequote

                    ...

                    R$-            $: $(dequote $1 $)
                    R$- $+         $: $>3 $1 $2

                Care  must  be  taken  to prevent unexpected
                results; for example,

                    "|someprogram < input > output"

                will have quotes stripped, but the result is
                probably  not  what you had in mind.  Fortu-
                nately these cases are rare.

      regex     The map definition on the K line contains  a
                regular  expression.   Any key input is com-
                pared to that  expression  using  the  POSIX
                regular   expressions   routines  regcomp(),
                regerr(), and regexec().  Refer to the docu-
                mentation for those routines for more infor-
                mation about the regular  expression  match-
                ing.  No rewriting of the key is done if the
                -m flag is used.  Without  it,  the  key  is
                discarded  or  if  -s if used, it is substi-
                tuted by the substring matches, delimited by
                $|  or  the string specified with the the -d
                flag.  The flags available for the map are















Sendmail Installation and Operation Guide         SMM:08-133


                    -n  not
                    -f  case sensitive
                    -b  basic regular expressions (default is extended)
                    -s  substring match
                    -d  set the delimiter used for -s
                    -a  append string to key
                    -m  match only, do not replace/discard value
                    -D  perform no lookup in deferred delivery mode.

                The -s flag can include an optional  parame-
                ter  which  can  be  used to select the sub-
                strings in the result of  the  lookup.   For
                example,

                    -s1,3,4

                Notes: to match a $ in a string, \$$ must be
                used.  If the pattern contains spaces,  they
                must be replaced with the blank substitution
                character, unless it is space itself.

      program   The arguments on the K line are the pathname
                to  a  program and any initial parameters to
                be passed.  When the map is called, the  key
                is  added  to the initial parameters and the
                program is invoked as the default user/group
                id.   The  first  line of standard output is
                returned as the value of the  lookup.   This
                has  many  potential  security problems, and
                has terrible performance; it should be  used
                only when absolutely necessary.

      macro     Set or clear a macro value.  To set a macro,
                pass the value as the first argument in  the
                map  lookup.   To clear a macro, do not pass
                an argument in  the  map  lookup.   The  map
                always returns the empty string.  Example of
                typical usage include:

                    Kstorage macro

                    ...

                    # set macro ${MyMacro} to the ruleset match
                    R$+ $: $(storage {MyMacro} $@ $1 $) $1
                    # set macro ${MyMacro} to an empty string
                    R$* $: $(storage {MyMacro} $@ $) $1
                    # clear macro ${MyMacro}
                    R$- $: $(storage {MyMacro} $) $1


      arith     Perform simple arithmetic  operations.   The
                operation  is  given as key, currently +, -,










SMM:08-134         Sendmail Installation and Operation Guide


                *, /, %, |, & (bitwise OR, AND), l (for less
                than),  =, and r (for random) are supported.
                The two operands  are  given  as  arguments.
                The  lookup returns the result of the compu-
                tation, i.e., TRUE or FALSE for comparisons,
                integer  values  otherwise.   The r operator
                returns a pseudo-random number  whose  value
                lies  between  the  first and second operand
                (which requires that the  first  operand  is
                smaller than the second).  All options which
                are possible for maps are ignored.  A simple
                example is:

                    Kcomp arith

                    ...

                    Scheck_etrn
                    R$* $: $(comp l $@ $&{load_avg} $@ 7 $) $1
                    RFALSE$# error ...


      socket    The  socket  map uses a simple request/reply
                protocol over TCP or UNIX domain sockets  to
                query an external server.  Both requests and
                replies are text based and encoded  as  net-
                strings,   i.e.,   a  string  "hello  there"
                becomes:

                    11:hello there,

                Note: neither requests nor replies end  with
                CRLF.

                The  request  consists  of  the database map
                name and the lookup key separated by a space
                character:


                    <mapname> ' ' <key>


                The  server responds with a status indicator
                and the result (if any):


                    <status> ' ' <result>


                The status indicator is one of the following
                upper case words:












Sendmail Installation and Operation Guide         SMM:08-135


                    OK       the key was found, result contains the looked up value
                    NOTFOUND the key was not found, the result is empty
                    TEMP     a temporary failure occured
                    TIMEOUT  a timeout occured on the server side
                    PERM     a permanent failure occured


                In  case  of errors (status TEMP, TIMEOUT or
                PERM)  the  result  field  may  contain   an
                explanatory message.

                Example replies:

                    31:OK resolved.address@example.com,


                in case of a successful lookup, or:

                    8:NOTFOUND,


                in case the key was not found, or:

                    55:TEMP this text explains that we had a temporary failure,


                in case of a failure.

                The  socket map uses the same syntax as mil-
                ters (see Section "X -- Mail Filter (Milter)
                Definitions")  to  specify  the  remote end-
                point, e.g.,

                    Ksocket mySocketMap inet:12345@127.0.0.1


                If multiple  socket  maps  define  the  same
                remote  endpoint,  they  will share a single
                connection to this endpoint.

           Most  of  these  accept  as  arguments  the  same
      optional  flags  and a filename (or a mapname for NIS;
      the filename is the root of the database path, so that
      ".db"  or  some  other  extension  appropriate for the
      database type will be added to get the actual database
      name).  Known flags are:

      -o        Indicates  that this map is optional -- that
                is, if it cannot be opened, no error is pro-
                duced,  and  sendmail  will behave as if the
                map existed but was empty.












SMM:08-136         Sendmail Installation and Operation Guide


      -N, -O    If neither -N or -O are specified,  sendmail
                uses an adaptive algorithm to decide whether
                or not to look for null bytes on the end  of
                keys.  It starts by trying both; if it finds
                any key with a  null  byte  it  never  tries
                again  without  a  null byte and vice versa.
                If -N is specified it never tries without  a
                null  byte  and  if -O is specified it never
                tries with a  null  byte.   Setting  one  of
                these can speed matches but are never neces-
                sary.  If both  -N  and  -O  are  specified,
                sendmail  will  never try any matches at all
                -- that is, everything will appear to  fail.

      -ax       Append  the  string x on successful matches.
                For example, the default host map appends  a
                dot on successful matches.

      -Tx       Append  the  string x on temporary failures.
                For example, x would be appended  if  a  DNS
                lookup  returned  "server  failed" or an NIS
                lookup could not locate a server.  See  also
                the -t flag.

      -f        Do not fold upper to lower case before look-
                ing up the key.

      -m        Match only (without  replacing  the  value).
                If  you  only  care about the existence of a
                key and not the value  (as  you  might  when
                searching  the  NIS  map  "hosts.byname" for
                example), this flag prevents  the  map  from
                substituting  the  value.   However,  The -a
                argument is still appended on a  match,  and
                the  default  is  still  taken  if the match
                fails.

      -kkeycol  The key column name  (for  NIS+)  or  number
                (for  text  lookups).  For LDAP maps this is
                an  LDAP  filter  string  in  which  %s   is
                replaced  with  the  literal contents of the
                lookup key and %0 is replaced with the  LDAP
                escaped contents of the lookup key according
                to RFC 2254.  If the flag -K is  used,  then
                %1  through  %9  are  replaced with the LDAP
                escaped contents of the arguments  specified
                in the map lookup.

      -vvalcol  The  value  column name (for NIS+) or number
                (for text lookups).  For LDAP maps  this  is
                the  name  of  one  or more attributes to be
                returned; multiple attributes can  be  sepa-
                rated  by  commas.   If  not  specified, all










Sendmail Installation and Operation Guide         SMM:08-137


                attributes  found  in  the  match  will   be
                returned.   The  attributes  listed can also
                include a type and one or  more  objectClass
                values for matching as described in the LDAP
                section.

      -zdelim   The column delimiter (for text lookups).  It
                can be a single character or one of the spe-
                cial strings "\n" or "\t" to  indicate  new-
                line   or   tab  respectively.   If  omitted
                entirely,  the  column  separator   is   any
                sequence of white space.  For LDAP maps this
                is the separator character to combine multi-
                ple  values into a single return string.  If
                not set, the LDAP lookup  will  only  return
                the first match found.  For DNS maps this is
                the separator character at which the  result
                of a query is cut off if is too long.

      -t        Normally, when a map attempts to do a lookup
                and  the  server   fails   (e.g.,   sendmail
                couldn't  contact  any  name server; this is
                not the same as an entry not being found  in
                the  map),  the  message  being processed is
                queued for future processing.  The  -t  flag
                turns  off this behavior, letting the tempo-
                rary failure (server down) act as though  it
                were  a permanent failure (entry not found).
                It is particularly useful for  DNS  lookups,
                where   someone  else's  misconfigured  name
                server can cause problems on  your  machine.
                However,  care  must be taken to ensure that
                you don't bounce mail that would be resolved
                correctly  if  you  tried  again.   A common
                strategy is to forward such mail to another,
                possibly better connected, mail server.

      -D        Perform no lookup in deferred delivery mode.
                This flag is set by  default  for  the  host
                map.

      -Sspacesub
                The  character to use to replace space char-
                acters after a successful map  lookup  (esp.
                useful for regex and syslog maps).

      -sspacesub
                For  the  dequote map only, the character to
                use to replace space characters after a suc-
                cessful dequote.

      -q        Don't dequote the key before lookup.











SMM:08-138         Sendmail Installation and Operation Guide


      -Llevel   For  the  syslog  map only, it specifies the
                level to use for the syslog call.

      -A        When rebuilding an alias file, the  -A  flag
                causes duplicate entries in the text version
                to be merged.  For example, two entries:

                    list:    user1, user2
                    list:    user3

                would be treated as though it were the  sin-
                gle entry

                    list:    user1, user2, user3

                in the presence of the -A flag.

           Some  additional flags are available for the host
      and dns maps:

      -d        delay: specify the resolver's retransmission
                time interval (in seconds).

      -r        retry:   specify  the  number  of  times  to
                retransmit a resolver query.

           The dns map has another flag:

      -B        basedomain: specify a domain that is  always
                appended to queries.

           The following additional flags are present in the
      ldap map only:

      -R        Do not auto chase referrals.  sendmail  must
                be  compiled  with  -DLDAP_REFERRALS  to use
                this flag.

      -n        Retrieve attribute names only.

      -Vsep     Retrieve both attributes name and  value(s),
                separated by sep.

      -rderef   Set  the  alias dereference option to one of
                never, always, search, or find.

      -sscope   Set search scope to one of  base,  one  (one
                level), or sub (subtree).

      -hhost    LDAP  server  hostname.  Some LDAP libraries
                allow you to specify  multiple,  space-sepa-
                rated  hosts  for  redundancy.  In addition,
                each of the hosts listed can be followed  by










Sendmail Installation and Operation Guide         SMM:08-139


                a  colon  and  a port number to override the
                default LDAP port.

      -pport    LDAP service port.

      -H LDAPURI
                Use the specified LDAP URI instead of speci-
                fying  the hostname and port separately with
                the the -h and -p options shown above.   For
                example,

                    -h server.example.com -p 389 -b dc=example,dc=com

                is equivalent to

                    -H ldap://server.example.com:389 -b dc=example,dc=com

                If  the  LDAP  library supports it, the LDAP
                URI format however  can  also  request  LDAP
                over   SSL  by  using  ldaps://  instead  of
                ldap://.  For example:

                    O LDAPDefaultSpec=-H ldaps://ldap.example.com -b dc=example,dc=com

                Similarly, if the LDAP library supports  it,
                It can also be used to specify a UNIX domain
                socket using ldapi://:

                    O LDAPDefaultSpec=-H ldapi://socketfile -b dc=example,dc=com


      -bbase    LDAP search base.

      -ltimelimit
                Time limit for LDAP queries.

      -Zsizelimit
                Size (number of matches) limit for  LDAP  or
                DNS queries.

      -ddistinguished_name
                The  distinguished  name  to use to login to
                the LDAP server.

      -Mmethod  The  method  to  authenticate  to  the  LDAP
                server.   Should  be  one of LDAP_AUTH_NONE,
                LDAP_AUTH_SIMPLE, or LDAP_AUTH_KRBV4.

      -Ppasswordfile
                The file containing the secret key  for  the
                LDAP_AUTH_SIMPLE  authentication  method  or
                the name of the  Kerberos  ticket  file  for
                LDAP_AUTH_KRBV4.










SMM:08-140         Sendmail Installation and Operation Guide


      -1        Force  LDAP  searches  to  only succeed if a
                single match is found.  If  multiple  values
                are  found,  the  search is treated as if no
                match was found.

      -wversion Set the LDAP API/protocol  version  to  use.
                The  default  depends  on  the  LDAP  client
                libraries in use.  For example,  -w  3  will
                cause  sendmail  to use LDAPv3 when communi-
                cating with the LDAP server.

      -K        Treat the LDAP search key as  multi-argument
                and  replace  %1  through %9 in the key with
                the LDAP  escaped  contents  of  the  lookup
                arguments specified in the map lookup.

           The dbm map appends the strings ".pag" and ".dir"
      to the given filename; the hash and btree maps  append
      ".db".  For example, the map specification

          Kuucp dbm -o -N /etc/mail/uucpmap

      specifies an optional map named "uucp" of class "dbm";
      it always has null bytes at the end of  every  string,
      and       the       data       is      located      in
      /etc/mail/uucpmap.{dir,pag}.

           The program makemap(8) can be used to  build  any
      of  the  three  database-oriented  maps.  It takes the
      following flags:

      -f        Do not fold upper to lower case in the  map.

      -N        Include null bytes in keys.

      -o        Append to an existing (old) file.

      -r        Allow  replacement  of  existing  keys; nor-
                mally, re-inserting an existing  key  is  an
                error.

      -v        Print what is happening.

      The  sendmail  daemon does not have to be restarted to
      read the new maps as long as you change them in place;
      file  locking  is  used so that the maps won't be read
      while they are being updated.

           New classes can be added in the routine setupmaps
      in file conf.c.













Sendmail Installation and Operation Guide         SMM:08-141


   5.10.  Q -- Queue Group Declaration

           In  addition  to the option QueueDirectory, queue
      groups can be declared that define a (group of)  queue
      directories  under  a  common  name.  The syntax is as
      follows:

          Qname {, field=value}+

      where name is the symbolic name  of  the  queue  group
      under which it can be referenced in various places and
      the "field=value" pairs define attributes of the queue
      group.   The  name  must  only consist of alphanumeric
      characters.  Fields are:

      Flags     Flags for this queue group.

      Nice      The nice(2) increment for the  queue  group.
                This value must be greater or equal zero.

      Interval  The time between two queue runs.

      Path      The queue directory of the group (required).

      Runners   The number of  parallel  runners  processing
                the  queue.   Note  that  F=f must be set if
                this value is greater than one.

      Jobs      The maximum number of jobs (messages  deliv-
                ered) per queue run.

      recipients
                The  maximum  number of recipients per enve-
                lope.  Envelopes with more than this  number
                of  recipients  will  be split into multiple
                envelopes in the same queue directory.   The
                default value 0 means no limit.

      Only the first character of the field name is checked.

           By default, a queue group named mqueue is defined
      that  uses  the  value of the QueueDirectory option as
      path.  Notice: all  paths  that  are  used  for  queue
      groups   must  be  subdirectories  of  QueueDirectory.
      Since they can be symbolic links, this  isn't  a  real
      restriction,  If  QueueDirectory uses a wildcard, then
      the directory one level up is considered the  ``base''
      directory  which  all  other  queue  directories  must
      share.  Please make sure that the queue directories do
      not overlap, e.g., do not specify













SMM:08-142         Sendmail Installation and Operation Guide


          O QueueDirectory=/var/spool/mqueue/*
          Qone, P=/var/spool/mqueue/dir1
          Qtwo, P=/var/spool/mqueue/dir2

      because  this  also  includes "dir1" and "dir2" in the
      default queue group.  However,

          O QueueDirectory=/var/spool/mqueue/main*
          Qone, P=/var/spool/mqueue/dir
          Qtwo, P=/var/spool/mqueue/other*

      is a valid queue group specification.

           Options listed in the ``Flags'' field can be used
      to  modify  the  behavior of a queue group.  The ``f''
      flag must be set if multiple queue  runners  are  sup-
      posed to work on the entries in a queue group.  Other-
      wise  sendmail  will  work  on  the  entries  strictly
      sequentially.

           The  ``Interval''  field  sets  the  time between
      queue runs.  If no queue group  specific  interval  is
      set, then the parameter of the -q option from the com-
      mand line is used.

           To control the  overall  number  of  concurrently
      active  queue  runners the option MaxQueueChildren can
      be set.  This limits the number of processes used  for
      running  the queues to MaxQueueChildren, though at any
      one time fewer processes may be active as a result  of
      queue options, completed queue runs, system load, etc.

           The maximum number of queue runners for an  indi-
      vidual  queue  group can be controlled via the Runners
      option.  If set to 0, entries in the queue will not be
      processed,  which  is  useful  to ``quarantine'' queue
      files.  The number of runners per queue group may also
      be  set  with  the  option  MaxRunnersPerQueue,  which
      applies to queue groups that have no individual limit.
      That  is,  the  default  value  for Runners is MaxRun-
      nersPerQueue if set, otherwise 1.

           The field Jobs describes the  maximum  number  of
      jobs  (messages delivered) per queue run, which is the
      queue group specific value of MaxQueueRunSize.

           Notice: queue groups should be declared after all
      queue  related  options  have  been  set because queue
      groups take their defaults from those options.  If  an
      option  is  set  after  a queue group declaration, the
      values of options in the queue group are  set  to  the
      defaults of sendmail unless explicitly set in the dec-
      laration.










Sendmail Installation and Operation Guide         SMM:08-143


           Each envelope is assigned to a queue group  based
      on  the  algorithm described in section ``Queue Groups
      and Queue Directories''.

   5.11.  X -- Mail Filter (Milter) Definitions

           The sendmail Mail Filter API (Milter) is designed
      to  allow third-party programs access to mail messages
      as they are being processed in order to  filter  meta-
      information  and  content.   They  are declared in the
      configuration file as:

          Xname {, field=value}*

      where name is the name of the filter (used  internally
      only)  and the "field=name" pairs define attributes of
      the filter.  Also see the documentation for the Input-
      MailFilters option for more information.

           Fields are:

          Socket    The socket specification
          Flags     Special flags for this filter
          Timeouts  Timeouts for this filter

      Only  the first character of the field name is checked
      (it's case-sensitive).

           The socket specification is one of the  following
      forms:

          S=inet: port @ host


          S=inet6: port @ host


          S=local: path

      The  first two describe an IPv4 or IPv6 socket listen-
      ing on a certain port at a given host or  IP  address.
      The  final  form  describes  a  named  socket  on  the
      filesystem at the given path.

           The following flags may  be  set  in  the  filter
      description.

      R   Reject connection if filter unavailable.

      T   Temporary fail connection if filter unavailable.

           If  neither F=R nor F=T is specified, the message
      is passed through sendmail in case of filter errors as










SMM:08-144         Sendmail Installation and Operation Guide


      if the failing filters were not present.

           The  timeouts  can  be  set using the four fields
      inside of the T= equate:

      C   Timeout for connecting to a filter.  If set to  0,
          the system's connect() timeout will be used.

      S   Timeout  for sending information from the MTA to a
          filter.

      R   Timeout for reading reply from the filter.

      E   Overall timeout between sending end-of-message  to
          filter and waiting for the final acknowledgment.

           Note  the separator between each timeout field is
      a  ';'.   The  default  values  (if  not   set)   are:
      T=C:5m;S:10s;R:10s;E:5m  where  s  is seconds and m is
      minutes.

           Examples:

          Xfilter1, S=local:/var/run/f1.sock, F=R
          Xfilter2, S=inet6:999@localhost, F=T, T=S:1s;R:1s;E:5m
          Xfilter3, S=inet:3333@localhost, T=C:2m


   5.12.  The User Database

           The user  database  is  deprecated  in  favor  of
      ``virtusertable''  and  ``genericstable'' as explained
      in the file cf/README.  If you have a version of send-
      mail  with  the user database package compiled in, the
      handling of sender and recipient  addresses  is  modi-
      fied.

           The  location of this database is controlled with
      the UserDatabaseSpec option.

      5.12.1.  Structure of the user database

              The database is a sorted (BTree-based)  struc-
         ture.  User records are stored with the key:

             user-name:field-name

         The   sorted  database  format  ensures  that  user
         records are clustered  together.   Meta-information
         is always stored with a leading colon.

              Field  names define both the syntax and seman-
         tics of the value.  Defined fields include:










Sendmail Installation and Operation Guide         SMM:08-145


         maildrop  The  delivery  address  for  this   user.
                   There  may  be  multiple  values  of this
                   record.   In  particular,  mailing  lists
                   will  have  one  maildrop record for each
                   user on the list.

         mailname  The outgoing mailname for this user.  For
                   each  outgoing  name,  there should be an
                   appropriate maildrop record for that name
                   to   allow   return   mail.    See   also
                   :default:mailname.

         mailsender
                   Changes any mail sent to this address  to
                   have the indicated envelope sender.  This
                   is intended for mailing lists,  and  will
                   normally  be  the  name of an appropriate
                   -request address.  It is very similar  to
                   the  owner-list syntax in the alias file.

         fullname  The full name of the user.

         office-address
                   The office address for this user.

         office-phone
                   The office phone number for this user.

         office-fax
                   The office FAX number for this user.

         home-address
                   The home address for this user.

         home-phone
                   The home phone number for this user.

         home-fax  The home FAX number for this user.

         project   A (short) description of the project this
                   person  is  affiliated with.  In the Uni-
                   versity this is often just  the  name  of
                   their graduate advisor.

         plan      A  pointer  to  a  file  from  which plan
                   information can be gathered.

              As of this writing, only a few of these fields
         are  actually  being used by sendmail: maildrop and
         mailname.  A finger program  that  uses  the  other
         fields is planned.












SMM:08-146         Sendmail Installation and Operation Guide


      5.12.2.  User database semantics

              When  the rewriting rules submit an address to
         the local mailer, the user name is  passed  through
         the  alias  file.   If no alias is found (or if the
         alias points back to the same  address),  the  name
         (with  ":maildrop"  appended) is then used as a key
         in the user database.  If no match  occurs  (or  if
         the  maildrop points at the same address), forward-
         ing is tried.

              If the first token of the user  name  returned
         by  ruleset  0  is  an  "@" sign, the user database
         lookup is skipped.  The intent  is  that  the  user
         database  will act as a set of defaults for a clus-
         ter (in our case, the Computer  Science  Division);
         mail sent to a specific machine should ignore these
         defaults.

              When mail is sent, the  name  of  the  sending
         user  is  looked  up in the database.  If that user
         has a "mailname" record, the value of  that  record
         is  used  as  their  outgoing name.  For example, I
         might have a record:

             eric:mailnameEric.Allman@CS.Berkeley.EDU

         This would cause my outgoing mail  to  be  sent  as
         Eric.Allman.

              If  a "maildrop" is found for the user, but no
         corresponding "mailname" record exists, the  record
         ":default:mailname" is consulted.  If present, this
         is the name of a host to override the  local  host.
         For  example,  in  our  case  we  would  set  it to
         "CS.Berkeley.EDU".  The effect is that anyone known
         in the database gets their outgoing mail stamped as
         "user@CS.Berkeley.EDU", but people  not  listed  in
         the database use the local hostname.

      5.12.3.  Creating the database[23]

              The user database is built from  a  text  file
         using  the  makemap utility (in the distribution in
         the makemap subdirectory).   The  text  file  is  a
         series  of  lines  corresponding to userdb records;
____________________
   [23]These instructions are known to be incomplete.  Other
features are available which provide similar  functionality,
e.g.,  virtual  hosting  and  mapping local addresses into a
generic form as explained in cf/README.












Sendmail Installation and Operation Guide         SMM:08-147


         each line has a key and a value separated by  white
         space.   The  key is always in the format described
         above -- for example:

             eric:maildrop

         This file is normally installed in a system  direc-
         tory;    for    example,   it   might   be   called
         /etc/mail/userdb.  To make the database version  of
         the map, run the program:

             makemap btree /etc/mail/userdb < /etc/mail/userdb

         Then  create  a  config  file  that uses this.  For
         example, using the V8 M4 configuration, include the
         following line in your .mc file:

             define(`confUSERDB_SPEC', /etc/mail/userdb)


6.  OTHER CONFIGURATION

        There  are  some  configuration  changes that can be
   made by recompiling  sendmail.   This  section  describes
   what  changes  can be made and what has to be modified to
   make them.  In most  cases  this  should  be  unnecessary
   unless you are porting sendmail to a new environment.

   6.1.  Parameters in devtools/OS/$oscf

           These  parameters  are  intended  to describe the
      compilation environment, not site policy,  and  should
      normally be defined in the operating system configura-
      tion file.  This section needs a complete rewrite.

      NDBM      If set, the new version of the  DBM  library
                that allows multiple databases will be used.
                If neither NDBM nor NEWDB are  set,  a  much
                less  efficient  method  of  alias lookup is
                used.

      NEWDB     If set, use the new  database  package  from
                Berkeley  (from  4.4BSD).   This  package is
                substantially faster than DBM or  NDBM.   If
                NEWDB  and  NDBM are both set, sendmail will
                read DBM files,  but  will  create  and  use
                NEWDB files.

      NIS       Include  support  for  NIS.  If set together
                with both NEWDB and NDBM, sendmail will cre-
                ate  both DBM and NEWDB files if and only if
                an alias file includes the substring  "/yp/"
                in   the   name.    This   is  intended  for










SMM:08-148         Sendmail Installation and Operation Guide


                compatibility with Sun Microsystems' mkalias
                program used on YP masters.

      NISPLUS   Compile in support for NIS+.

      NETINFO   Compile  in  support  for NetInfo (NeXT sta-
                tions).

      LDAPMAP   Compile in support for  LDAP  X500  queries.
                Requires  libldap and liblber from the Umich
                LDAP  3.2  or  3.3  release  or   equivalent
                libraries  for  other LDAP libraries such as
                OpenLDAP.

      HESIOD    Compile in support for Hesiod.

      MAP_NSD   Compile in support for IRIX NSD lookups.

      MAP_REGEX Compile in support  for  regular  expression
                matching.

      DNSMAP    Compile  in  support  for DNS map lookups in
                the sendmail.cf file.

      PH_MAP    Compile in support for ph lookups.

      SASL      Compile in support for SASL, a required com-
                ponent for SMTP Authentication support.

      STARTTLS  Compile in support for STARTTLS.

      EGD       Compile  in support for the "Entropy Gather-
                ing Daemon" to provide  better  random  data
                for TLS.

      TCPWRAPPERS
                Compile in support for TCP Wrappers.

      _PATH_SENDMAILCF
                The pathname of the sendmail.cf file.

      _PATH_SENDMAILPID
                The pathname of the sendmail.pid file.

      SM_CONF_SHM
                Compile  in  support  for shared memory, see
                section about "/var/spool/mqueue".

      MILTER    Compile in support for  contacting  external
                mail filters built with the Milter API.

           There are also several compilation flags to indi-
      cate the environment such as "_AIX3" and "_SCO_unix_".










Sendmail Installation and Operation Guide         SMM:08-149


      See  the  sendmail/README file for the latest scoop on
      these flags.

   6.2.  Parameters in sendmail/conf.h

           Parameters and compilation options are defined in
      conf.h.   Most  of these need not normally be tweaked;
      common parameters are all  in  sendmail.cf.   However,
      the  sizes  of  certain  primitive  vectors, etc., are
      included in this  file.   The  numbers  following  the
      parameters are their default value.

           This  document is not the best source of informa-
      tion for compilation flags  in  conf.h  --  see  send-
      mail/README or sendmail/conf.h itself.

      MAXLINE [2048]
                  The maximum line length of any input line.
                  If message lines exceed this  length  they
                  will  still  be  processed correctly; how-
                  ever,  header  lines,  configuration  file
                  lines,  alias lines, etc., must fit within
                  this limit.

      MAXNAME [256]
                  The maximum length of any name, such as  a
                  host or a user name.

      MAXPV [256] The  maximum  number  of parameters to any
                  mailer.  This limits the number of recipi-
                  ents  that  may  be passed in one transac-
                  tion.  It can be set to any arbitrary num-
                  ber  above  about  10, since sendmail will
                  break up a delivery into  smaller  batches
                  as  needed.   A  higher  number may reduce
                  load on your system, however.

      MAXQUEUEGROUPS [50]
                  The maximum number of queue groups.

      MAXATOM [1000]
                  The maximum number of atoms (tokens) in  a
                  single  address.  For example, the address
                  "eric@CS.Berkeley.EDU" is seven atoms.

      MAXMAILERS [25]
                  The maximum number of mailers that may  be
                  defined  in  the configuration file.  This
                  value is defined in include/sendmail/send-
                  mail.h.

      MAXRWSETS [200]
                  The  maximum number of rewriting sets that










SMM:08-150         Sendmail Installation and Operation Guide


                  may be defined.  The first half  of  these
                  are  reserved  for  numeric  specification
                  (e.g., ``S92''), while the upper half  are
                  reserved    for    auto-numbering   (e.g.,
                  ``Sfoo'').  Thus, with a value of  200  an
                  attempt  to  use ``S99'' will succeed, but
                  ``S100'' will fail.

      MAXPRIORITIES [25]
                  The  maximum  number  of  values  for  the
                  "Precedence:"  field  that  may be defined
                  (using the P line in sendmail.cf).

      MAXUSERENVIRON [100]
                  The maximum number of items  in  the  user
                  environment  that will be passed to subor-
                  dinate mailers.

      MAXMXHOSTS [100]
                  The maximum number of MX records  we  will
                  accept for any single host.

      MAXMAPSTACK [12]
                  The  maximum  number  of  maps that may be
                  "stacked" in a sequence class map.

      MAXMIMEARGS [20]
                  The maximum number of arguments in a  MIME
                  Content-Type: header; additional arguments
                  will be ignored.

      MAXMIMENESTING [20]
                  The maximum depth to which  MIME  messages
                  may  be nested (that is, nested Message or
                  Multipart documents; this does  not  limit
                  the  number of components in a single Mul-
                  tipart document).

      MAXDAEMONS [10]
                  The maximum  number  of  sockets  sendmail
                  will  open  for  accepting  connections on
                  different ports.

      MAXMACNAMELEN [25]
                  The maximum length of a macro name.

      A number of other compilation  options  exist.   These
      specify  whether  or  not specific code should be com-
      piled in.  Ones marked with * are 0/1 valued.

      NETINET*    If set, support for Internet protocol net-
                  working is compiled in.  Previous versions
                  of sendmail referred to  this  as  DAEMON;










Sendmail Installation and Operation Guide         SMM:08-151


                  this old usage is now incorrect.  Defaults
                  on; turn it off in the  Makefile  if  your
                  system doesn't support the Internet proto-
                  cols.

      NETINET6*   If set, support  for  IPv6  networking  is
                  compiled   in.    It  must  be  separately
                  enabled by adding  DaemonPortOptions  set-
                  tings.

      NETISO*     If  set, support for ISO protocol network-
                  ing is compiled in (it may be  appropriate
                  to #define this in the Makefile instead of
                  conf.h).

      NETUNIX*    If set, support for UNIX domain sockets is
                  compiled  in.   This  is  used for control
                  socket support.

      LOG         If set, the syslog routine in use at  some
                  sites  is  used.   This  makes an informa-
                  tional log record for  each  message  pro-
                  cessed,  and  makes  a higher priority log
                  record   for   internal   system   errors.
                  STRONGLY  RECOMMENDED  --  if  you want no
                  logging, turn it off in the  configuration
                  file.

      MATCHGECOS* Compile  in  the code to do ``fuzzy match-
                  ing'' on the GECOS field  in  /etc/passwd.
                  This  also  requires  that  the MatchGECOS
                  option be turned on.

      NAMED_BIND* Compile in code to use the Berkeley Inter-
                  net  Name  Domain (BIND) server to resolve
                  TCP/IP host names.

      NOTUNIX     If you are using a non-UNIX  mail  format,
                  you  can set this flag to turn off special
                  processing of UNIX-style "From " lines.

      USERDB*     Include  the  experimental  Berkeley  user
                  information database package.  This adds a
                  new level of local name expansion  between
                  aliasing and forwarding.  It also uses the
                  NEWDB package.  This may change in  future
                  releases.

      The  following  options are normally turned on in per-
      operating-system clauses in conf.h.

      IDENTPROTO* Compile in the IDENT protocol  as  defined
                  in  RFC  1413.   This  defaults on for all










SMM:08-152         Sendmail Installation and Operation Guide


                  systems except  Ultrix,  which  apparently
                  has the interesting "feature" that when it
                  receives a "host unreachable"  message  it
                  closes  all open connections to that host.
                  Since some  firewall  gateways  send  this
                  error code when you access an unauthorized
                  port (such as 113, used by IDENT),  Ultrix
                  cannot receive email from such hosts.

      SYSTEM5     Set  all  of  the  compilation  parameters
                  appropriate for System V.

      HASFLOCK*   Use Berkeley-style flock instead of System
                  V  lockf  to  do file locking.  Due to the
                  highly unusual semantics of  locks  across
                  forks in lockf, this should always be used
                  if at all possible.

      HASINITGROUPS
                  Set this if  your  system  has  the  init-
                  groups()  call (if you have multiple group
                  support).  This is the default if  SYSTEM5
                  is not defined or if you are on HPUX.

      HASUNAME    Set  this  if you have the uname(2) system
                  call (or corresponding  library  routine).
                  Set by default if SYSTEM5 is set.

      HASGETDTABLESIZE
                  Set  this if you have the getdtablesize(2)
                  system call.

      HASWAITPID  Set this if  you  have  the  haswaitpid(2)
                  system call.

      FAST_PID_RECYCLE
                  Set this if your system can possibly reuse
                  the same pid in the same second of time.

      SFS_TYPE    The mechanism that can be used to get file
                  system  capacity  information.  The values
                  can be one of SFS_USTAT (use the  ustat(2)
                  syscall), SFS_4ARGS (use the four argument
                  statfs(2) syscall), SFS_VFS (use  the  two
                  argument   statfs(2)   syscall   including
                  <sys/vfs.h>), SFS_MOUNT (use the two argu-
                  ment     statfs(2)    syscall    including
                  <sys/mount.h>), SFS_STATFS  (use  the  two
                  argument   statfs(2)   syscall   including
                  <sys/statfs.h>), SFS_STATVFS (use the  two
                  argument   statfs(2)   syscall   including
                  <sys/statvfs.h>), or SFS_NONE (no  way  to
                  get this information).










Sendmail Installation and Operation Guide         SMM:08-153


      LA_TYPE     The   load   average  type.   Details  are
                  described below.

      The are several built-in ways of  computing  the  load
      average.   Sendmail tries to auto-configure them based
      on imperfect guesses; you can select one using the  cc
      option -DLA_TYPE=type, where type is:

      LA_INT      The  kernel stores the load average in the
                  kernel as an array of long integers.   The
                  actual  values  are  scaled  by  a  factor
                  FSCALE (default 256).

      LA_SHORT    The kernel stores the load average in  the
                  kernel as an array of short integers.  The
                  actual  values  are  scaled  by  a  factor
                  FSCALE (default 256).

      LA_FLOAT    The  kernel stores the load average in the
                  kernel as an  array  of  double  precision
                  floats.

      LA_MACH     Use MACH-style load averages.

      LA_SUBR     Call  the  getloadavg  routine  to get the
                  load average as an array of doubles.

      LA_ZERO     Always return zero as  the  load  average.
                  This is the fallback case.

      If  type  LA_INT,  LA_SHORT, or LA_FLOAT is specified,
      you may also need to specify _PATH_UNIX (the  path  to
      your  system  binary)  and LA_AVENRUN (the name of the
      variable containing the load average  in  the  kernel;
      usually "_avenrun" or "avenrun").

   6.3.  Configuration in sendmail/conf.c

           The following changes can be made in conf.c.

      6.3.1.  Built-in Header Semantics

              Not  all  header  semantics are defined in the
         configuration file.  Header lines that should  only
         be  included  by  certain mailers (as well as other
         more obscure semantics) must be  specified  in  the
         HdrInfo  table  in conf.c.  This table contains the
         header name (which should be in all lower case) and
         a  set  of  header control flags (described below),
         The flags are:

         H_ACHECK    Normally when the check is made to  see
                     if  a  header line is compatible with a










SMM:08-154         Sendmail Installation and Operation Guide


                     mailer, sendmail  will  not  delete  an
                     existing  line.   If  this flag is set,
                     sendmail  will  delete  even   existing
                     header  lines.  That is, if this bit is
                     set and the mailer does not  have  flag
                     bits   set   that  intersect  with  the
                     required mailer  flags  in  the  header
                     definition  in  sendmail.cf, the header
                     line is always deleted.

         H_EOH       If this header field is set,  treat  it
                     like a blank line, i.e., it will signal
                     the end of the header and the beginning
                     of the message text.

         H_FORCE     Add  this  header  entry  even  if  one
                     existed in the message  before.   If  a
                     header  entry  does  not  have this bit
                     set,  sendmail  will  not  add  another
                     header  line  if  a header line of this
                     name already existed.  This would  nor-
                     mally  be  used to stamp the message by
                     everyone who handled it.

         H_TRACE     If set, this  is  a  timestamp  (trace)
                     field.   If  the number of trace fields
                     in a message exceeds  a  preset  amount
                     the  message is returned on the assump-
                     tion that it has an aliasing loop.

         H_RCPT      If set, this field  contains  recipient
                     addresses.  This is used by the -t flag
                     to determine who to send to when it  is
                     collecting recipients from the message.

         H_FROM      This flag  indicates  that  this  field
                     specifies a sender.  The order of these
                     fields in the HdrInfo  table  specifies
                     sendmail's  preference  for which field
                     to return error messages to.

         H_ERRORSTO  Addresses in this header should receive
                     error messages.

         H_CTE       This   header  is  a  Content-Transfer-
                     Encoding header.

         H_CTYPE     This header is a Content-Type header.

         H_STRIPVAL  Strip the value from  the  header  (for
                     Bcc:).












Sendmail Installation and Operation Guide         SMM:08-155


         Let's look at a sample HdrInfo specification:

             struct hdrinfo                    HdrInfo[] =
             {
                      /* originator fields, most to least significant  */
                 "resent-sender",              H_FROM,
                 "resent-from",                H_FROM,
                 "sender",                     H_FROM,
                 "from",                       H_FROM,
                 "full-name",                  H_ACHECK,
                 "errors-to",                  H_FROM|H_ERRORSTO,
                      /* destination fields */
                 "to",                         H_RCPT,
                 "resent-to",                  H_RCPT,
                 "cc",                         H_RCPT,
                 "bcc",                        H_RCPT|H_STRIPVAL,
                      /* message identification and control */
                 "message",                    H_EOH,
                 "text",                       H_EOH,
                      /* trace fields */
                 "received",                   H_TRACE|H_FORCE,
                      /* miscellaneous fields */
                 "content-transfer-encoding",  H_CTE,
                 "content-type",               H_CTYPE,

                 NULL,                         0,
             };

         This  structure  indicates that the "To:", "Resent-
         To:",  and  "Cc:"  fields  all  specify   recipient
         addresses.   Any "Full-Name:" field will be deleted
         unless the required mailer flag (indicated  in  the
         configuration  file)  is specified.  The "Message:"
         and "Text:" fields will terminate the header; these
         are  used  by  random dissenters around the network
         world.  The "Received:" field will always be added,
         and can be used to trace messages.

              There  are  a number of important points here.
         First, header fields are  not  added  automatically
         just  because  they  are  in the HdrInfo structure;
         they must be specified in the configuration file in
         order  to  be  added  to  the  message.  Any header
         fields mentioned in the configuration file but  not
         mentioned  in  the  HdrInfo  structure have default
         processing  performed;  that  is,  they  are  added
         unless  they  were in the message already.  Second,
         the HdrInfo structure only specifies  cliched  pro-
         cessing; certain headers are processed specially by
         ad hoc code regardless of the status  specified  in
         HdrInfo.   For  example,  the "Sender:" and "From:"
         fields are always scanned on ARPANET mail to deter-











SMM:08-156         Sendmail Installation and Operation Guide


         mine the sender[24]; this is used  to  perform  the
         "return  to  sender"  function.   The  "From:"  and
         "Full-Name:" fields are used to determine the  full
         name  of  the sender if possible; this is stored in
         the macro $x and used in a number of ways.

      6.3.2.  Restricting Use of Email

              If it is necessary to restrict mail through  a
         relay,  the  checkcompat  routine  can be modified.
         This routine is called for every recipient address.
         It  returns an exit status indicating the status of
         the message.  The status EX_OK accepts the address,
         EX_TEMPFAIL queues the message for a later try, and
         other values (commonly EX_UNAVAILABLE)  reject  the
         message.  It is up to checkcompat to print an error
         message (using usrerr) if the message is  rejected.
         For example, checkcompat could read:

             int
             checkcompat(to, e)
                 register ADDRESS *to;
                 register ENVELOPE *e;
             {
                 register STAB *s;

                 s = stab("private", ST_MAILER, ST_FIND);
                 if (s != NULL && e->e_from.q_mailer != LocalMailer &&
                     to->q_mailer == s->s_mailer)
                 {
                     usrerr("No private net mail allowed through this machine");
                     return (EX_UNAVAILABLE);
                 }
                 if (MsgSize > 50000 && bitnset(M_LOCALMAILER, to->q_mailer))
                 {
                     usrerr("Message too large for non-local delivery");
                     e->e_flags |= EF_NORETURN;
                     return (EX_UNAVAILABLE);
                 }
                 return (EX_OK);
             }

         This would reject messages greater than 50000 bytes
         unless they were local.  The EF_NORETURN  flag  can
         be  set in e->e_flags to suppress the return of the
         actual body of the message  in  the  error  return.
         The  actual use of this routine is highly dependent
         on the implementation, and use should be limited.
____________________
   [24]Actually, this is no longer true in SMTP; this infor-
mation is contained in the envelope.  The older ARPANET pro-
tocols  did not completely distinguish envelope from header.











Sendmail Installation and Operation Guide         SMM:08-157


      6.3.3.  New Database Map Classes

              New key maps can be added by creating a  class
         initialization  function  and  a  lookup  function.
         These are then added to the routine setupmaps.

              The initialization function is called as

             xxx_map_init(MAP *map, char *args)

         The map is an internal data structure.  The args is
         a  pointer to the portion of the configuration file
         line following the map class name; flags and  file-
         names  can  be  extracted from this line.  The ini-
         tialization function must return true  if  it  suc-
         cessfully opened the map, false otherwise.

              The lookup function is called as

             xxx_map_lookup(MAP *map, char buf[], char **av, int *statp)

         The  map  defines  the map internally.  The buf has
         the input key.  This may be  (and  often  is)  used
         destructively.   The  av  is  a  list  of arguments
         passed in from the rewrite line.  The lookup  func-
         tion  should return a pointer to the new value.  If
         the map lookup fails, *statp should be  set  to  an
         exit  status  code; in particular, it should be set
         to EX_TEMPFAIL if recovery is to  be  attempted  by
         the higher level code.

      6.3.4.  Queueing Function

              The routine shouldqueue is called to decide if
         a message should be  queued  or  processed  immedi-
         ately.   Typically this compares the message prior-
         ity to the current load average.  The default defi-
         nition is:

             bool
             shouldqueue(pri, ctime)
                 long pri;
                 time_t ctime;
             {
                 if (CurrentLA < QueueLA)
                     return false;
                 return (pri > (QueueFactor / (CurrentLA - QueueLA + 1)));
             }

         If  the  current load average (global variable Cur-
         rentLA,  which  is  set  before  this  function  is
         called) is less than the low threshold load average
         (option x, variable QueueLA),  shouldqueue  returns










SMM:08-158         Sendmail Installation and Operation Guide


         false  immediately  (that is, it should not queue).
         If  the  current  load  average  exceeds  the  high
         threshold   load   average   (option   X,  variable
         RefuseLA), shouldqueue  returns  true  immediately.
         Otherwise,  it  computes  the function based on the
         message  priority,  the  queue  factor  (option  q,
         global  variable  QueueFactor), and the current and
         threshold load averages.

              An implementation wishing to take  the  actual
         age  of  the  message into account can also use the
         ctime parameter, which is the time that the message
         was first submitted to sendmail.  Note that the pri
         parameter is already  weighted  by  the  number  of
         times  the  message  has  been tried (although this
         tends to lower the priority  of  the  message  with
         time);  the  expectation is that the ctime would be
         used as an "escape clause" to ensure that  messages
         are eventually processed.

      6.3.5.  Refusing Incoming SMTP Connections

              The function refuseconnections returns true if
         incoming SMTP connections should be  refused.   The
         current  implementation is based exclusively on the
         current load average and the  refuse  load  average
         option (option X, global variable RefuseLA):

             bool
             refuseconnections()
             {
                 return (RefuseLA > 0 && CurrentLA >= RefuseLA);
             }

         A  more  clever  implementation  could look at more
         system resources.

      6.3.6.  Load Average Computation

              The routine getla  returns  the  current  load
         average  (as  a rounded integer).  The distribution
         includes several possible implementations.  If  you
         are  porting  to  a new environment you may need to
         add some new tweaks.[25]




____________________
   [25]If you do,  please  send  updates  to  sendmail@Send-
mail.ORG.












Sendmail Installation and Operation Guide         SMM:08-159


   6.4.  Configuration in sendmail/daemon.c

           The  file  sendmail/daemon.c contains a number of
      routines that are dependent on  the  local  networking
      environment.   The  version  supplied assumes you have
      BSD style sockets.

           In previous releases,  we  recommended  that  you
      modify the routine maphostname if you wanted to gener-
      alize $[ ... $] lookups.  We now  recommend  that  you
      create a new keyed map instead.

   6.5.  LDAP

           In  this section we assume that sendmail has been
      compiled with support for LDAP.

      6.5.1.  LDAP Recursion

              LDAP Recursion allows you to add types to  the
         search  attributes  on  an  LDAP map specification.
         The syntax is:

         -v ATTRIBUTE[:TYPE[:OBJECTCLASS[|OBJECTCLASS|...]]]

              The new TYPEs are:

         NORMAL    This   attribute   type   specifies   the
                   attribute to add to the  results  string.
                   This is the default.

         DN        Any   matches   for  this  attribute  are
                   expected to have a value of a fully qual-
                   ified  distinguished name.  sendmail will
                   lookup that DN and apply  the  attributes
                   requested to the returned DN record.

         FILTER    Any   matches   for  this  attribute  are
                   expected to  have  a  value  of  an  LDAP
                   search  filter.   sendmail will perform a
                   lookup with the same  parameters  as  the
                   original  search  but replaces the search
                   filter with the one specified here.

         URL       Any  matches  for  this   attribute   are
                   expected  to have a value of an LDAP URL.
                   sendmail will perform a  lookup  of  that
                   URL   and   use   the  results  from  the
                   attributes named in that URL.  Note  how-
                   ever  that  the  search is done using the
                   current LDAP  connection,  regardless  of
                   what  is  specified  as  the scheme, LDAP
                   host, and LDAP port in the LDAP URL.










SMM:08-160         Sendmail Installation and Operation Guide


         Any  untyped  attributes  are   considered   NORMAL
         attributes as described above.

              The  optional  OBJECTCLASS  (| separated) list
         contains the  objectClass  values  for  which  that
         attribute  applies.   If  the  list  is  given, the
         attribute named will  only  be  used  if  the  LDAP
         record  being  returned  is a member of that object
         class.  Note that  if  these  new  value  attribute
         TYPEs  are  used in an AliasFile option setting, it
         will need to be double quoted to  prevent  sendmail
         from misparsing the colons.

              Note  that  LDAP recursion attributes which do
         not ultimately point to an LDAP record are not con-
         sidered an error.

         6.5.1.1.  Example

                 Since  examples  usually help clarify, here
            is an example which uses all  four  of  the  new
            types:

                O LDAPDefaultSpec=-h ldap.example.com -b dc=example,dc=com

                Kexample ldap
                         -z,
                         -k (&(objectClass=sendmailMTAAliasObject)(sendmailMTAKey=%0))
                         -v sendmailMTAAliasValue,mail:NORMAL:inetOrgPerson,
                            uniqueMember:DN:groupOfUniqueNames,
                            sendmailMTAAliasSearch:FILTER:sendmailMTAAliasObject,
                            sendmailMTAAliasURL:URL:sendmailMTAAliasObject


                 That definition specifies that:

             + Any    value   in   a   sendmailMTAAliasValue
               attribute will be added to the result  string
               regardless of object class.
             + The  mail  attribute  will  be  added  to the
               result string if the LDAP record is a  member
               of the inetOrgPerson object class.
             + The  uniqueMember  attribute  is  a recursive
               attribute, used  only  in  groupOfUniqueNames
               records, and should contain an LDAP DN point-
               ing to another LDAP record.  The desire  here
               is  to  return  the mail attribute from those
               DNs.
             + The  sendmailMTAAliasSearch   attribute   and
               sendmailMTAAliasURL  are  both  used  only if
               referenced in a sendmailMTAAliasObject.  They
               are  both recursive, the first for a new LDAP
               search string and the latter for an LDAP URL.










Sendmail Installation and Operation Guide         SMM:08-161


   6.6.  STARTTLS

           In  this section we assume that sendmail has been
      compiled  with  support  for  STARTTLS.   To  properly
      understand the use of STARTTLS in sendmail, it is nec-
      essary to understand at least some basics about  X.509
      certificates and public key cryptography.  This infor-
      mation can be found in books about SSL/TLS or  on  WWW
      sites, e.g., "http://www.OpenSSL.org/".

      6.6.1.  Certificates for STARTTLS

              When  acting  as  a  server, sendmail requires
         X.509 certificates to support STARTTLS: one as cer-
         tificate  for the server (ServerCertFile and corre-
         sponding private ServerKeyFile) at least  one  root
         CA  (CACertFile),  i.e., a certificate that is used
         to sign other certificates, and a path to a  direc-
         tory  which  contains  other CAs (CACertPath).  The
         file specified via CACertFile can  contain  several
         certificates of CAs.  The DNs of these certificates
         are sent to the client during the TLS handshake (as
         part  of  the  CertificateRequest)  as  the list of
         acceptable CAs.  However, do not list too many root
         CAs  in  that file, otherwise the TLS handshake may
         fail; e.g.,

             error:14094417:SSL routines:SSL3_READ_BYTES:
             sslv3 alert illegal parameter:s3_pkt.c:964:SSL alert number 47

         You should probably put only the CA cert into  that
         file that signed your own cert(s), or at least only
         those you trust.   The  CACertPath  directory  must
         contain  the hashes of each CA certificate as file-
         names (or as links to them).  Symbolic links can be
         generated  with  the  following  two (Bourne) shell
         commands:

             C=FileName_of_CA_Certificate
             ln -s $C `openssl x509 -noout -hash < $C`.0

         An X.509 certificate is also required for authenti-
         cation  in  client  mode (ClientCertFile and corre-
         sponding private ClientKeyFile), however,  sendmail
         will  always use STARTTLS when offered by a server.
         The client and server certificates can  be  identi-
         cal.   Certificates can be obtained from a certifi-
         cate authority or created with the help of OpenSSL.
         The  required  format  for certificates and private
         keys is PEM.  To allow  for  automatic  startup  of
         sendmail,  private  keys (ServerKeyFile, ClientKey-
         File) must be stored  unencrypted.   The  keys  are
         only  protected  by  the  permissions  of  the file










SMM:08-162         Sendmail Installation and Operation Guide


         system.  Never make a private key  available  to  a
         third party.

      6.6.2.  PRNG for STARTTLS

              STARTTLS  requires a strong pseudo random num-
         ber generator (PRNG) to operate properly.   Depend-
         ing  on the TLS library you use, it may be required
         to explicitly initialize the PRNG with random data.
         OpenSSL  makes  use of /dev/urandom(4) if available
         (this corresponds  to  the  compile  flag  HASURAN-
         DOMDEV).   On  systems  which  lack this support, a
         random file must be specified  in  the  sendmail.cf
         file  using  the  option  RandFile.  It is strongly
         advised to use the "Entropy Gathering  Daemon"  EGD
         from  Brian Warner on those systems to provide use-
         ful random data.  In this case,  sendmail  must  be
         compiled with the flag EGD, and the RandFile option
         must  point  to  the  EGD   socket.    If   neither
         /dev/urandom(4)  nor EGD are available, you have to
         make sure that useful random data is available  all
         the time in RandFile.  If the file hasn't been mod-
         ified in the last 10 minutes before it is  supposed
         to  be  used  by sendmail the content is considered
         obsolete.  One method for generating this file is:

             openssl rand -out /etc/mail/randfile -rand /path/to/file:...256

         See the OpenSSL documentation for more information.
         In  this case, the PRNG for TLS is only seeded with
         other random data if the  DontBlameSendmail  option
         InsufficientEntropy  is  set.   This is most likely
         not sufficient for certain actions,  e.g.,  genera-
         tion of (temporary) keys.

              Please  see the OpenSSL documentation or other
         sources for further information about certificates,
         their creation and their usage, the importance of a
         good PRNG, and other aspects of TLS.

   6.7.  Encoding of STARTTLS and AUTH related Macros

           Macros that contain  STARTTLS  and  AUTH  related
      data  which  comes  from  outside  sources,  e.g., all
      macros containing information from  certificates,  are
      encoded  to  avoid problems with non-printable or spe-
      cial characters.  The latter are '\', '<',  '>',  '(',
      ')',  '"',  '+', and ' '.  All of these characters are
      replaced by their value in hexadecimal with a  leading
      '+'.  For example:

          /C=US/ST=California/O=endmail.org/OU=private/CN=Darth Mail (Cert)/
          Email=darth+cert@endmail.org










Sendmail Installation and Operation Guide         SMM:08-163


      is encoded as:

          /C=US/ST=California/O=endmail.org/OU=private/
          CN=Darth+20Mail+20+28Cert+29/Email=darth+2Bcert@endmail.org

      (line breaks have been inserted for readability).  The
      macros  which  are  subject  to  this   encoding   are
      {cert_subject},      {cert_issuer},      {cn_subject},
      {cn_issuer},   as   well    as    {auth_authen}    and
      {auth_author}.

7.  ACKNOWLEDGEMENTS

        I've  worked  on  sendmail  for many years, and many
   employers have been remarkably patient about  letting  me
   work  on a large project that was not part of my official
   job.  This includes time on the  INGRES  Project  at  the
   University of California at Berkeley, at Britton Lee, and
   again on the Mammoth and Titan Projects at Berkeley.

        Much of the second wave of improvements resulting in
   version  8.1  should be credited to Bryan Costales of the
   International Computer Science Institute.  As  he  passed
   me drafts of his book on sendmail I was inspired to start
   working on things again.  Bryan  was  also  available  to
   bounce ideas off of.

        Gregory Neil Shapiro of Worcester Polytechnic Insti-
   tute has become instrumental in all  phases  of  sendmail
   support  and development, and was largely responsible for
   getting versions 8.8 and 8.9 out the door.

        Many, many people contributed  chunks  of  code  and
   ideas  to  sendmail.  It has proven to be a group network
   effort.  Version 8 in particular  was  a  group  project.
   The  following people and organizations made notable con-
   tributions:

       Claus Assmann
       John Beck, Hewlett-Packard & Sun Microsystems
       Keith Bostic, CSRG, University of California, Berkeley
       Andrew Cheng, Sun Microsystems
       Michael J. Corrigan, University of California, San Diego
       Bryan Costales, International Computer Science Institute & InfoBeat
       Par (Pell) Emanuelsson
       Craig Everhart, Transarc Corporation
       Per Hedeland, Ericsson
       Tom Ivar Helbekkmo, Norwegian School of Economics
       Kari Hurtta, Finnish Meteorological Institute
       Allan E. Johannesen, WPI
       Jonathan Kamens, OpenVision Technologies, Inc.
       Takahiro Kanbe, Fuji Xerox Information Systems Co., Ltd.
       Brian Kantor, University of California, San Diego










SMM:08-164         Sendmail Installation and Operation Guide


       John Kennedy, Cal State University, Chico
       Murray S. Kucherawy, HookUp Communication Corp.
       Bruce Lilly, Sony U.S.
       Karl London
       Motonori Nakamura, Ritsumeikan University & Kyoto University
       John Gardiner Myers, Carnegie Mellon University
       Neil Rickert, Northern Illinois University
       Gregory Neil Shapiro, WPI
       Eric Schnoebelen, Convex Computer Corp.
       Eric Wassenaar, National Institute for Nuclear and High Energy Physics, Amsterdam
       Randall Winchester, University of Maryland
       Christophe Wolfhugel, Pasteur Institute & Herve Schauer Consultants (Paris)
       Exactis.com, Inc.

   I apologize for anyone I have omitted, misspelled, misat-
   tributed,  or otherwise missed.  At this point, I suspect
   that at least a hundred people have contributed code, and
   many  more  have contributed ideas, comments, and encour-
   agement.  I've tried to list them in the RELEASE_NOTES in
   the distribution directory.  I appreciate their contribu-
   tion as well.

        Special thanks are reserved for Michael Corrigan and
   Christophe  Wolfhugel, who besides being wonderful guinea
   pigs and contributors have also consented to be added  to
   the  ``sendmail@Sendmail.ORG'' list and, by answering the
   bulk of the questions sent to that list, have freed me up
   to do other work.






































                          APPENDIX  A


                      COMMAND LINE FLAGS




     Arguments   must   be   presented   with  flags  before
addresses.  The flags are:

-Ax       Select an alternative .cf  file  which  is  either
          sendmail.cf  for  -Am  or  submit.cf  for -Ac.  By
          default the .cf file is chosen based on the opera-
          tion  mode.   For -bm (default), -bs, and -t it is
          submit.cf if it exists, for all others it is send-
          mail.cf.

-bx       Set operation mode to x.  Operation modes are:

              m   Deliver mail (default)
              s   Speak SMTP on input side
              a*  ``Arpanet'' mode (get envelope sender information from header)
              d   Run as a daemon in background
              D   Run as a daemon in foreground
              t   Run in test mode
              v   Just verify addresses, don't collect or deliver
              i   Initialize the alias database
              p   Print the mail queue
              P   Print overview over the mail queue (requires shared memory)
              h   Print the persistent host status database
              H   Purge expired entries from the persistent host status database


-Btype    Indicate body type.

-Cfile    Use a different configuration file.  Sendmail runs
          as the invoking user (rather than root) when  this
          flag is specified.

-D logfile
          Send  debugging  output  to  the indicated logfile
          instead of stdout.

-dlevel   Set debugging level.

-f addr   The envelope sender address is set to addr.   This
          address  may  also  be used in the From: header if
          that header is missing during initial  submission.
____________________
   *Deprecated.




Sendmail Installation and Operation Guide         SMM:08-165







SMM:08-166         Sendmail Installation and Operation Guide


          The envelope sender address is used as the recipi-
          ent for delivery status notifications and may also
          appear in a Return-Path: header.

-F name   Sets the full name of this user to name.

-G        When  accepting  messages  via  the  command line,
          indicate that they are for relay (gateway) submis-
          sion.   sendmail  may complain about syntactically
          invalid messages, e.g.,  unqualified  host  names,
          rather  than  fixing  them  when this flag is set.
          sendmail will not do any canonicalization in  this
          mode.

-h cnt    Sets  the "hop count" to cnt.  This represents the
          number of times this message has been processed by
          sendmail  (to  the  extent that it is supported by
          the underlying networks).  Cnt is incremented dur-
          ing  processing,  and  if  it reaches MAXHOP (cur-
          rently 25) sendmail throws away the  message  with
          an error.

-L tag    Sets  the  identifier  used for syslog.  Note that
          this identifier is set as early as possible.  How-
          ever,  sendmail  may  be  used  if  problems arise
          before the command line arguments are processed.

-n        Don't do aliasing or forwarding.

-N notifications
          Tag all addresses being sent as wanting the  indi-
          cated  notifications,  which  consists of the word
          "NEVER" or a comma-separated  list  of  "SUCCESS",
          "FAILURE",  and  "DELAY"  for successful delivery,
          failure, and a message that is stuck  in  a  queue
          somewhere.  The default is "FAILURE,DELAY".

-r addr   An obsolete form of -f.

-oxvalue  Set  option  x  to  the  specified  value.   These
          options are described in Section 5.6.

-Ooption=value
          Set option to the specified value (for  long  form
          option  names).   These  options  are described in
          Section 5.6.

-Mxvalue  Set macro x to the specified value.

-pprotocol
          Set the sending protocol.  Programs are encouraged
          to  set  this.   The  protocol field can be in the
          form  protocol:host  to  set  both   the   sending










Sendmail Installation and Operation Guide         SMM:08-167


          protocol   and   sending   host.    For   example,
          "-pUUCP:uunet" sets the sending protocol  to  UUCP
          and  the  sending  host  to uunet.  (Some existing
          programs use -oM to set the r and s  macros;  this
          is equivalent to using -p.)

-qtime    Try to process the queued up mail.  If the time is
          given, a sendmail will start one or more processes
          to  run through the queue(s) at the specified time
          interval to deliver  queued  mail;  otherwise,  it
          only runs once.  Each of these processes acts on a
          workgroup.  These  processes  are  also  known  as
          workgroup  processes  or  WGP's  for  short.  Each
          workgroup is responsible for controlling the  pro-
          cessing  of  one  or  more queues; workgroups help
          manage the use of system  resources  by  sendmail.
          Each  workgroup may have one or more children con-
          currently processing queues depending on the  set-
          ting of MaxQueueChildren.

-qptime   Similar  to  -q  with a time argument, except that
          instead of periodically  starting  WGP's  sendmail
          starts  persistent  WGP's  that  alternate between
          processing queues and sleeping.  The sleep time is
          specified  by  the time argument; it defaults to 1
          second, except that a WGP always sleeps at least 5
          seconds if their queues were empty in the previous
          run.  Persistent processes are managed by a  queue
          control  process  (QCP).   The  QCP  is the parent
          process of the WGP's.  Typically the QCP  will  be
          the sendmail daemon (when started with -bd or -bD)
          or a special process (named Queue  control)  (when
          started  without -bd or -bD).  If a persistent WGP
          ceases to be active for some  reason  another  WGP
          will  be started by the QCP for the same workgroup
          in most cases. When  a  persistent  WGP  has  core
          dumped,  the  debug  flag no_persistent_restart is
          set  or  the  specific  persistent  WGP  has  been
          restarted too many times already then the WGP will
          not be started again and a message will be  logged
          to  this  effect.   To  stop  (SIGTERM) or restart
          (SIGHUP) persistent WGP's the  appropriate  signal
          should  be sent to the QCP. The QCP will propagate
          the signal to all of the WGP's and if  appropriate
          restart the persistent WGP's.

-qGname   Run the jobs in the queue group name once.

-q[!]Xstring
          Run  the  queue  once,  limiting the jobs to those
          matching Xstring.  The key letter X can  be  I  to
          limit  based on queue identifier, R to limit based
          on recipient, S to limit based on sender, or Q  to










SMM:08-168         Sendmail Installation and Operation Guide


          limit  based  on quarantine reason for quarantined
          jobs.  A particular queued job is accepted if  one
          of the corresponding attributes contains the indi-
          cated string.  The optional  !  character  negates
          the condition tested.  Multiple -qX flags are per-
          mitted,  with  items  with  the  same  key  letter
          "or'ed"  together,  and  items  with different key
          letters "and'ed" together.

-Q[reason]
          Quarantine a normal queue  items  with  the  given
          reason  or unquarantine quarantined queue items if
          no reason is given.  This should only be used with
          some  sort  of item matching using -q[!]Xstring as
          described above.

-R ret    What information you want returned if the  message
          bounces;  ret  can  be  "HDRS" for headers only or
          "FULL" for headers plus body.  This is  a  request
          only;  the  other end is not required to honor the
          parameter.  If "HDRS" is specified  local  bounces
          also return only the headers.

-t        Read  the  header  for  "To:",  "Cc:",  and "Bcc:"
          lines, and send to everyone listed in those lists.
          The  "Bcc:"  line  will be deleted before sending.
          Any addresses  in  the  argument  vector  will  be
          deleted from the send list.

-V envid  The indicated envid is passed with the envelope of
          the message and returned if the message bounces.

-X logfile
          Log all traffic in and  out  of  sendmail  in  the
          indicated  logfile  for debugging mailer problems.
          This produces a  lot  of  data  very  quickly  and
          should be used sparingly.

     There  are a number of options that may be specified as
primitive flags.  These are the e,  i,  m,  and  v  options.
Also, the f option may be specified as the -s flag.  The DSN
related options "-N", "-R", and  "-V"  have  no  effects  on
sendmail running as daemon.























                        APPENDIX  B


                     QUEUE FILE FORMATS




     This  appendix describes the format of the queue files.
These files live in a queue directory.  The  individual  qf,
hf, Qf, df, and xf files may be stored in separate qf/, df/,
and xf/ subdirectories if they  are  present  in  the  queue
directory.

     All  queue  files  have  the name ttYMDhmsNNppppp where
YMDhmsNNppppp is the id for this message and  the  tt  is  a
type.  The individual letters in the id are:

Y    Encoded year

M    Encoded month

D    Encoded day

h    Encoded hour

m    Encoded minute

s    Encoded second

NN   Encoded envelope number

ppppp
     At least five decimal digits of the process ID

     All files with the same id collectively define one mes-
sage.  Due to the use  of  memory-buffered  files,  some  of
these files may never appear on disk.

     The types are:

qf   The  queue control file.  This file contains the infor-
     mation necessary to process the job.

hf   The same as a queue control file, but for a quarantined
     queue job.

df   The data file.  The message body (excluding the header)
     is kept in this file.  Sometimes the  df  file  is  not
     stored  in  the  same directory as the qf file; in this
     case, the qf file contains a `d' record which names the
     queue directory that contains the df file.



Sendmail Installation and Operation Guide         SMM:08-169







SMM:08-170         Sendmail Installation and Operation Guide


tf   A temporary file.  This is an image of the qf file when
     it is being rebuilt.  It should be renamed to a qf file
     very quickly.

xf   A  transcript  file, existing during the life of a ses-
     sion showing everything that happens during  that  ses-
     sion.  Sometimes the xf file must be generated before a
     queue group has been selected; in  this  case,  the  xf
     file will be stored in a directory of the default queue
     group.

Qf   A ``lost'' queue control file.  sendmail renames  a  qf
     file to Qf if there is a severe (configuration) problem
     that  cannot  be  solved  without  human  intervention.
     Search  the logfile for the queue file id to figure out
     what happened.  After you resolved the problem, you can
     rename the Qf file to qf and send it again.

     The  queue  control  file  is structured as a series of
lines each beginning with a code letter.  The lines  are  as
follows:

V    The  version  number  of the queue file format, used to
     allow new sendmail binaries to read queue files created
     by  older versions.  Defaults to version zero.  Must be
     the first line of the file if present.   For  8.12  the
     version number is 6.

A    The  information  given  by  the AUTH= parameter of the
     "MAIL FROM:" command or  $f@$j  if  sendmail  has  been
     called directly.

H    A  header definition.  There may be any number of these
     lines.  The order  is  important:  they  represent  the
     order  in the final message.  These use the same syntax
     as header definitions in the configuration file.

C    The    controlling    address.     The    syntax     is
     "localuser:aliasname".   Recipient  addresses following
     this line will be flagged so that  deliveries  will  be
     run  as the localuser (a user name from the /etc/passwd
     file); aliasname is the name of the alias that expanded
     to this address (used for printing messages).

q    The quarantine reason for quarantined queue items.

Q    The  ``original  recipient'',  specified  by the ORCPT=
     field in an ESMTP transaction.   Used  exclusively  for
     Delivery  Status Notifications.  It applies only to the
     following `R' line.

r    The ``final recipient'' used for Delivery Status  Noti-
     fications.   It applies only to the following `R' line.










Sendmail Installation and Operation Guide         SMM:08-171


R    A recipient address.  This will normally be  completely
     aliased, but is actually realiased when the job is pro-
     cessed.  There will be one  line  for  each  recipient.
     Version  1 qf files also include a leading colon-termi-
     nated list of flags, which can be `S' to return a  mes-
     sage on successful final delivery, `F' to return a mes-
     sage on failure, `D' to return a message if the message
     is  delayed,  `B'  to  indicate that the body should be
     returned, `N' to suppress returning the body,  and  `P'
     to declare this as a ``primary'' (command line or SMTP-
     session) address.

S    The sender address.  There may only  be  one  of  these
     lines.

T    The job creation time.  This is used to compute when to
     time out the job.

P    The current message priority.  This is  used  to  order
     the  queue.  Higher numbers mean lower priorities.  The
     priority changes as the message sits in the queue.  The
     initial  priority  depends on the message class and the
     size of the message.

M    A message.  This line is printed by the mailq  command,
     and  is generally used to store status information.  It
     can contain any text.

F    Flag bits, represented as one letter per flag.  Defined
     flag bits are r indicating that this is a response mes-
     sage and w indicating that a warning message  has  been
     sent  announcing that the mail has been delayed.  Other
     flag bits are: 8: the body contains  8bit  data,  b:  a
     Bcc:  header  should  be  removed,  d: the mail has RET
     parameters (see RFC 1894), n: the body of  the  message
     should  not  be  returned  in  case of an error, s: the
     envelope has been split.

N    The total number of delivery attempts.

K    The time (as seconds since January 1, 1970) of the last
     delivery attempt.

d    If  the df file is in a different directory than the qf
     file, then a `d'  record  is  present,  specifying  the
     directory in which the df file resides.

I    The  i-number  of  the  data  file; this can be used to
     recover your mail queue after a disastrous disk  crash.

$    A  macro  definition.  The values of certain macros are
     passed through to the queue run phase.











SMM:08-172         Sendmail Installation and Operation Guide


B    The body type.  The remainder of the  line  is  a  text
     string  defining the body type.  If this field is miss-
     ing, the body type is assumed to be "undefined" and  no
     special  processing  is  attempted.   Legal  values are
     "7BIT" and "8BITMIME".

Z    The original envelope id (from the ESMTP  transaction).
     For Deliver Status Notifications only.

     As  an  example,  the following is a queue file sent to
"eric@mammoth.Berkeley.EDU"  and   "bostic@okeeffe.CS.Berke-
ley.EDU"[1]:

    V4
    T711358135
    K904446490
    N0
    P2100941
    $_eric@localhost
    ${daemon_flags}
    Seric
    Ceric:100:1000:sendmail@vangogh.CS.Berkeley.EDU
    RPFD:eric@mammoth.Berkeley.EDU
    RPFD:bostic@okeeffe.CS.Berkeley.EDU
    H?P?Return-path: <^g>
    H??Received: by vangogh.CS.Berkeley.EDU (5.108/2.7) id AAA06703;
        Fri, 17 Jul 1992 00:28:55 -0700
    H??Received: from mail.CS.Berkeley.EDU by vangogh.CS.Berkeley.EDU (5.108/2.7)
        id AAA06698; Fri, 17 Jul 1992 00:28:54 -0700
    H??Received: from [128.32.31.21] by mail.CS.Berkeley.EDU (5.96/2.5)
        id AA22777; Fri, 17 Jul 1992 03:29:14 -0400
    H??Received: by foo.bar.baz.de (5.57/Ultrix3.0-C)
        id AA22757; Fri, 17 Jul 1992 09:31:25 GMT
    H?F?From: eric@foo.bar.baz.de (Eric Allman)
    H?x?Full-name: Eric Allman
    H??Message-id: <9207170931.AA22757@foo.bar.baz.de>
    H??To: sendmail@vangogh.CS.Berkeley.EDU
    H??Subject: this is an example message

This  shows  the person who sent the message, the submission
time (in seconds since January 1, 1970), the message  prior-
ity,  the message class, the recipients, and the headers for
the message.




____________________
   [1]This  example is contrived and probably inaccurate for
your environment.  Glance over it to get  an  idea;  nothing
can replace looking at what your own system generates.















                        APPENDIX  C


                  SUMMARY OF SUPPORT FILES




     This is a summary of the support  files  that  sendmail
creates or generates.  Many of these can be changed by edit-
ing the sendmail.cf file; check there  to  find  the  actual
pathnames.

/usr/sbin/sendmail
          The binary of sendmail.

/usr/bin/newaliases
          A  link  to  /usr/sbin/sendmail;  causes the alias
          database to be rebuilt.  Running this  program  is
          completely  equivalent  to giving sendmail the -bi
          flag.

/usr/bin/mailq
          Prints a listing of the mail queue.  This  program
          is equivalent to using the -bp flag to sendmail.

/etc/mail/sendmail.cf
          The configuration file, in textual form.

/etc/mail/helpfile
          The SMTP help file.

/etc/mail/statistics
          A statistics file; need not be present.

/etc/mail/sendmail.pid
          Created in daemon mode; it contains the process id
          of the current SMTP daemon.  If you  use  this  in
          scripts;  use  ``head  -1''  to get just the first
          line; the second line contains  the  command  line
          used  to  invoke the daemon, and later versions of
          sendmail may add more  information  to  subsequent
          lines.

/etc/mail/aliases
          The textual version of the alias file.

/etc/mail/aliases.db
          The alias file in hash(3) format.

/etc/mail/aliases.{pag,dir}
          The alias file in ndbm(3) format.



Sendmail Installation and Operation Guide         SMM:08-173







SMM:08-174         Sendmail Installation and Operation Guide


/var/spool/mqueue
          The  directory in which the mail queue(s) and tem-
          porary files reside.

/var/spool/mqueue/qf*
          Control (queue) files for messages.

/var/spool/mqueue/df*
          Data files.

/var/spool/mqueue/tf*
          Temporary versions of the qf  files,  used  during
          queue file rebuild.

/var/spool/mqueue/xf*
          A transcript of the current session.















































Sendmail Installation and Operation Guide           SMM:08-3


                          TABLE OF CONTENTS

1.  BASIC INSTALLATION ................................    7
   1.1.  Compiling Sendmail ...........................    7
      1.1.1.  Tweaking the Build Invocation ...........    7
      1.1.2.  Creating a Site Configuration File ......    8
      1.1.3.  Tweaking the Makefile ...................    8
      1.1.4.  Compilation and installation ............    9
   1.2.  Configuration Files ..........................   10
   1.3.  Details of Installation Files ................   12
      1.3.1.  /usr/sbin/sendmail ......................   12
      1.3.2.  /etc/mail/sendmail.cf ...................   12
      1.3.3.  /etc/mail/submit.cf .....................   13
      1.3.4.  /usr/bin/newaliases .....................   13
      1.3.5.  /usr/bin/hoststat .......................   13
      1.3.6.  /usr/bin/purgestat ......................   13
      1.3.7.  /var/spool/mqueue .......................   14
      1.3.8.  /var/spool/clientmqueue .................   14
      1.3.9.  /var/spool/mqueue/.hoststat .............   15
      1.3.10.  /etc/mail/aliases* .....................   15
      1.3.11.  /etc/rc or /etc/init.d/sendmail ........   15
      1.3.12.  /etc/mail/helpfile .....................   16
      1.3.13.  /etc/mail/statistics ...................   16
      1.3.14.  /usr/bin/mailq .........................   16
      1.3.15.  sendmail.pid ...........................   18
      1.3.16.  Map Files ..............................   18
2.  NORMAL OPERATIONS .................................   19
   2.1.  The System Log ...............................   19
      2.1.1.  Format ..................................   19
      2.1.2.  Levels ..................................   20
   2.2.  Dumping State ................................   21
   2.3.  The Mail Queues ..............................   21
      2.3.1.  Queue Groups and Queue Directories ......   21
      2.3.2.  Queue Runs ..............................   22
      2.3.3.  Manual Intervention .....................   23
      2.3.4.  Printing the queue ......................   23
      2.3.5.  Forcing the queue .......................   24
      2.3.6.  Quarantined Queue Items .................   25
   2.4.  Disk Based Connection Information ............   26
   2.5.  The Service Switch ...........................   27
   2.6.  The Alias Database ...........................   28
      2.6.1.  Rebuilding the alias database ...........   30
      2.6.2.  Potential problems ......................   30
      2.6.3.  List owners .............................   31
   2.7.  User Information Database ....................   31
   2.8.  Per-User Forwarding (.forward Files) .........   31
   2.9.  Special Header Lines .........................   32
      2.9.1.  Errors-To: ..............................   32
      2.9.2.  Apparently-To: ..........................   32
      2.9.3.  Precedence ..............................   33
   2.10.  IDENT Protocol Support ......................   33
3.  ARGUMENTS .........................................   34
   3.1.  Queue Interval ...............................   34










SMM:08-4           Sendmail Installation and Operation Guide


   3.2.  Daemon Mode ..................................   35
   3.3.  Forcing the Queue ............................   35
   3.4.  Debugging ....................................   36
   3.5.  Changing the Values of Options ...............   37
   3.6.  Trying a Different Configuration File ........   37
   3.7.  Logging Traffic ..............................   38
   3.8.  Testing Configuration Files ..................   38
   3.9.  Persistent Host Status Information ...........   40
4.  TUNING ............................................   40
   4.1.  Timeouts .....................................   41
      4.1.1.  Queue interval ..........................   41
      4.1.2.  Read timeouts ...........................   41
      4.1.3.  Message timeouts ........................   44
   4.2.  Forking During Queue Runs ....................   45
   4.3.  Queue Priorities .............................   46
   4.4.  Load Limiting ................................   46
   4.5.  Resource Limits ..............................   47
   4.6.   Measures against Denial of Service Attacks
      .................................................   47
   4.7.  Delivery Mode ................................   48
   4.8.  Log Level ....................................   49
   4.9.  File Modes ...................................   50
      4.9.1.  To suid or not to suid?  ................   50
      4.9.2.  Turning off security checks .............   51
   4.10.  Connection Caching ..........................   54
   4.11.  Name Server Access ..........................   55
   4.12.  Moving the Per-User Forward Files ...........   57
   4.13.  Free Space ..................................   57
   4.14.  Maximum Message Size ........................   58
   4.15.  Privacy Flags ...............................   58
   4.16.  Send to Me Too ..............................   58
5.  THE WHOLE SCOOP ON THE CONFIGURATION FILE .........   58
   5.1.  R and S -- Rewriting Rules ...................   59
      5.1.1.  The left hand side ......................   60
      5.1.2.  The right hand side .....................   60
      5.1.3.  Semantics of rewriting rule sets ........   63
      5.1.4.  Ruleset hooks ...........................   64
         5.1.4.1.  check_relay ........................   65
         5.1.4.2.  check_mail .........................   65
         5.1.4.3.  check_rcpt .........................   65
         5.1.4.4.  check_data .........................   65
         5.1.4.5.  check_compat .......................   65
         5.1.4.6.  check_eoh ..........................   66
         5.1.4.7.  check_eom ..........................   66
         5.1.4.8.  check_etrn .........................   66
         5.1.4.9.  check_expn .........................   67
         5.1.4.10.  check_vrfy ........................   67
         5.1.4.11.  trust_auth ........................   67
         5.1.4.12.  tls_client ........................   67
         5.1.4.13.  tls_server ........................   67
         5.1.4.14.  tls_rcpt ..........................   67
         5.1.4.15.  srv_features ......................   68
         5.1.4.16.  try_tls ...........................   69










Sendmail Installation and Operation Guide           SMM:08-5


         5.1.4.17.  authinfo ..........................   69
         5.1.4.18.  queuegroup ........................   70
         5.1.4.19.  greet_pause .......................   70
      5.1.5.  IPC mailers .............................   71
   5.2.  D -- Define Macro ............................   71
   5.3.  C and F -- Define Classes ....................   82
   5.4.  M -- Define Mailer ...........................   85
   5.5.  H -- Define Header ...........................   93
   5.6.  O -- Set Option ..............................   95
   5.7.  P -- Precedence Definitions ..................  126
   5.8.  V -- Configuration Version Level .............  126
   5.9.  K -- Key File Declaration ....................  128
   5.10.  Q -- Queue Group Declaration ................  141
   5.11.  X -- Mail Filter (Milter) Definitions .......  143
   5.12.  The User Database ...........................  144
      5.12.1.  Structure of the user database .........  144
      5.12.2.  User database semantics ................  146
      5.12.3.  Creating the database[23] ..............  146
6.  OTHER CONFIGURATION ...............................  147
   6.1.  Parameters in devtools/OS/$oscf ..............  147
   6.2.  Parameters in sendmail/conf.h ................  149
   6.3.  Configuration in sendmail/conf.c .............  153
      6.3.1.  Built-in Header Semantics ...............  153
      6.3.2.  Restricting Use of Email ................  156
      6.3.3.  New Database Map Classes ................  157
      6.3.4.  Queueing Function .......................  157
      6.3.5.  Refusing Incoming SMTP Connections ......  158
      6.3.6.  Load Average Computation ................  158
   6.4.  Configuration in sendmail/daemon.c ...........  159
   6.5.  LDAP .........................................  159
      6.5.1.  LDAP Recursion ..........................  159
         6.5.1.1.  Example ............................  160
   6.6.  STARTTLS .....................................  161
      6.6.1.  Certificates for STARTTLS ...............  161
      6.6.2.  PRNG for STARTTLS .......................  162
   6.7.   Encoding  of  STARTTLS  and  AUTH  related
      Macros ..........................................  162
7.  ACKNOWLEDGEMENTS ..................................  163
Appendix A.  COMMAND LINE FLAGS .......................  165
Appendix B.  QUEUE FILE FORMATS .......................  169
Appendix C.  SUMMARY OF SUPPORT FILES .................  173






















SMM:08-6           Sendmail Installation and Operation Guide



















                 This page intentionally left blank;
          replace it with a blank sheet for double-sided output.








































